Crestron AMP-2210S/3210S Commercial Power Amplifiers, 4/8 Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc.
Regulatory Compliance As of the date of manufacture, the AMP-2210S/3210S has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron AMP-2210S/3210S Commercial Power Amplifiers Contents Commercial Power Amplifiers, 4/8: AMP-2210S/3210S 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.................................................................................................................
Crestron AMP-2210S/3210S Commercial Power Amplifiers Commercial Power Amplifiers, 4/8: AMP-2210S/3210S Introduction Crestron® AMP-series Commercial Power Amplifiers provide a perfect combination of high output and efficiency for all types of professional audio applications. 100% Crestron engineered and built, these amplifiers are ENERGY STAR® qualified to enable organizations to fulfill their green initiatives without compromising audio performance.
Commercial Power Amplifiers Crestron AMP-2210S/3210S ENERGY STAR® Qualified Their ultra-efficient design allows the AMP-2210S/3210S to meet demanding ENERGY STAR qualification requirements, affording a cost reducing solution for boardrooms, auditoriums, and other commercial systems. Auto power down places the amplifier into a low power standby state if no input signal is detected for 30 minutes. The amplifier quickly powers back on the instant an input signal is detected.
Crestron AMP-2210S/3210S Commercial Power Amplifiers Applications The following diagram shows an AMP-2210S/3210S in a basic application. AMP-2210S/3210S in a Basic Application (AMP-3210S Shown) Specifications Specifications for the AMP-2210S/3210S are listed in the following table.
Commercial Power Amplifiers Crestron AMP-2210S/3210S AMP-2210S/3210S Specifications (Continued) SPECIFICATION DETAILS Audio Typical of mono amplifier channels (Continued) Damping Factor >100 Protection Over current, over/under voltage, over temperature, DC offset Frequency Response 20 Hz to 20 kHz ±0.5 dB THD 0.05% at 1kHz at full rated power at 4/8 Ohms, 8 Ohms bridged, or 70/100 Volts; 0.1% at 20 Hz to 20 kHz, 120 W at 8 Ohms; 0.2% at 20 Hz to 20 kHz, 210 W at 4 Ohms; 0.
Crestron AMP-2210S/3210S Commercial Power Amplifiers AMP-2210S/3210S Specifications (Continued) SPECIFICATION DETAILS Environmental (Continued) Heat Dissipation, AMP-3210S 137 BTU/Hr @ 8 Ohms, all channels driven at 1/8 power; 162 BTU/Hr @ 4 Ohms, all channels driven at 1/8 power; 110 BTU/Hr, all channels idle; <3.
Commercial Power Amplifiers Crestron AMP-2210S/3210S AMP-3210S Physical View (Rear) AMP-2210S/3210S Overall Dimensions (AMP-3210S Shown) 6 Commercial Power Amplifiers: AMP-2210S/3210S Operations & Installation Guide – DOC.
Crestron AMP-2210S/3210S Commercial Power Amplifiers AMP-2210S/3210S Connectors, Controls & Indicators # CONNECTORS*, CONTROLS & INDICATORS 1 PWR LED 2 INPUT 1 - 3 LED (3) Green LEDs (2 on 2210S) indicates signal presence on each corresponding channel NOTE: The LEDs are inactive in standby mode 3 OUTPUT 1 – 3, CLIP/FAULT (3) Amber LEDs (2 on 2210S) indicate a clipping condition on each corresponding channel; (3) Red LEDs (2 on 2210S) indicate over temperature, over current, over or under power s
Commercial Power Amplifiers Crestron AMP-2210S/3210S AMP-2210S/3210S Connectors, Controls & Indicators (Continued) * # CONNECTORS*, CONTROLS & INDICATORS 10 ON/REMOTE/OFF (1) 3-position slide switch; Selects between all channels powered on, off, or remote controlled 11 110-240V~50/60Hz 120W MAX (1) IEC C14 male chassis plug, main power input; Mates with removable power cord (included) DESCRIPTION Interface connectors for INPUT, SPEAKER OUTPUT, and REMOTE ports are provided with the unit.
Crestron AMP-2210S/3210S Commercial Power Amplifiers Setup Installation Ventilation The AMP-2210S/3210S should be used in a well-ventilated area. The venting holes should not be obstructed under any circumstances. To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications. Consider using forced air ventilation and/or incrementing the spacing between units to reduce overheating.
Commercial Power Amplifiers Crestron AMP-2210S/3210S Ear Attachment for Rack Mounting 4. Stacking Repeat procedure (steps 1 through 3) to attach the remaining ear to the opposite side. Four “feet” are provided with the AMP-2210S/3210S so that if the unit is not rack mounted, the rubber feet can provide stability when the unit is placed on a flat surface or stacked. These feet should be attached prior to the hookup procedure. Refer to the following illustration for placement of the feet.
Crestron AMP-2210S/3210S Commercial Power Amplifiers Hardware Hookup Connect the Device Make the necessary connections as called out in the illustration that follows this paragraph. Apply power after all connections have been made. Hardware Connections for the AMP-3210S NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an earth ground (building steel).
Commercial Power Amplifiers Bridging Inputs/Outputs Crestron AMP-2210S/3210S 4. Remove the fuse from the fuse holder and insert a new fuse. 5. Insert the fuse holder in the AMP-2210T/3210T/2210HT. 6. Push in the fuse holder with a flat head screwdriver. While pushing in the fuse holder, turn the screwdriver clockwise until the fuse holder sets into place. 7. Push in the fuse holder a little further and turn the screwdriver clockwise until the fuse holder locks in place. 8.
Crestron AMP-2210S/3210S Commercial Power Amplifiers Operation Ensure that the procedures and instructions given in “Setup” on page 9 have been completed, and then do the following: Set all INPUT CH LEVEL knobs to their center detent position. These can be adjusted as necessary to balance the sound between channels or to accommodate different audio sources.
Commercial Power Amplifiers Crestron AMP-2210S/3210S Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. AMP-2210S/3210S Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION PWR LED does not illuminate AMP-2210S/3210S is not receiving power Verify that the AMP-2210S/3210S is connected to an AC outlet. Check the fuse.
Crestron AMP-2210S/3210S Commercial Power Amplifiers Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Commercial Power Amplifiers Crestron AMP-2210S/3210S This page is intentionally left blank. 16 Commercial Power Amplifiers: AMP-2210S/3210S Operations & Installation Guide – DOC.
Crestron AMP-2210S/3210S Commercial Power Amplifiers This page is intentionally left blank. Operations & Installation Guide – DOC.
Crestron Electronics, Inc 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 7251A (2031866) 09.11 Specifications subject to change without notice.
