Installation Guide

ManualsBrandsCrane ManualsBathEconomiser Big Foot Elongated Toilet Bowl Only in White

Thank you for selecting Crane Plumbing Products. To ensure this product installs properly, please read these

instructions carefully before you begin. Be sure your installation conforms to local codes.

REMOVE OLD TOILET: Close toilet supply valve and ush the toilet. Sponge any remaining water from the bowl. Discon-

nect and remove supply line. If replacing valve, rst shut off the main water supply. Remove mounting bolts and lift bowl off

toilet ange. Plug waste opening to prevent sewer gas from escaping. Clean away old wax, etc. from installation area.

Before Beginning: The toilet is in two cartons. One contains the bowl, and the other has the tank, cover and assorted parts.

Assuming that your bathroom has a four inch drain with a slotted toilet ange and cold water supply line in place, to com-

plete your installation you will need the following items, not supplied: two closet bolts, wax ring or bowl gasket, supply pipe

and shut off valve, toilet stop. A Word of Caution: The new toilet is made of ne china like the best quality tableware. It is

ruggedly constructed: however extra care should be exercised during installation when rough handling and the danger of

dropped tools threaten to chip or crack it. Water Supply: If your cold water line is through the wall, install an Angle Stop.

If it is through the oor, install a Straight Stop.

Installing the Toilet Bowl and Tank

If the toilet you are installing is a

“Back” or wall outlet unit, a closet

ange must be installed in the wall

4” above the oor. The ange must

be perpendicular to the oor, and

aligned so the bowl mounting bolts

will be parallel to the oor. To in-

stall, unplug the waste outlet and

slide the bowl toward the closet

ange so the bolts project through

the bowl mounting holes. Install the

washers with,“This Side Up” toward

you and thread on nuts. Tighten the

nuts alternating from side to side.

DO NOT OVERTIGHTEN. VITRE-

OUS CHINA EASILY CHIPS AND

CRACKS. Pour water into the bowl

to prevent the escape of sewer gas.

Unplug oor waste opening. Gently

place the bowl, right side up, in posi-

tion with the toilet mounting bolts pro-

truding through the holes in the china

base. Press down, with a slight twist-

ing motion, on the top center, with your

full weight. Make sure the bowl is as

level as possible. If needed, you can

use wedges under the bowl to help

leveling. Put the washers (Marked:

This Side Up) and nuts on the bolts.

Tighten them evenly and snugly.

DO NOT OVERTIGHTEN NUTS, AS

VITREOUS CHINA EASILY CHIPS

AND CRACKS. Pour water into the

bowl to prevent the escape of sewer

gas.

Clean the immediate oor area

thoroughly. Insert new toilet bolts in the

slotted ange, bolt heads down. The toilet

bowl should be placed upside down,

on soft material to prevent scratching.

Place the slightly warmed wax ring in

the circular recess in the base of the

bowl. NOTE: It is recommended that a

wax setting ring with ange be used.

Floor mounted, back outlet bowls

must be fastened to the oor with

Lag Screws (Supplied by others).

Slip the plastic washer, marked side

up, onto the lag screw and screw

into pre drilled pilot holes.

The tank should be inverted on the

oor after removing the lid and parts

bag. Open the plastic envelope and

place the large doughnut shaped

washer snugly on the threaded tank

outlet. Invert the tank and place it on

the bowl so that the large washer

ts evenly into the bowl water inlet

opening. Make sure tank is centered

and properly sealed. Place the rub-

ber washer on the bolts and insert

the bolts downward through the bolt

holes. Position the metal washer on

each bolt. With tank parallel to wall,

alternately nger tighten nuts. Using

a Wrench, alternately turn the nuts

until the tank is in contact with the

bowl piers.

CAUTION: Do Not Overtighten to

avoid cracking china.

INSTALLATION INSTRUCTIONS

PRESSURE ASSIST TOILETS

ATTENTION INSTALLER: PLEASE LEAVE THESE INSTRUCTIONS WITH THE CONSUMER

Neoprene

Seal

Summary of content (3 pages)

PAGE 1
ATTENTION INSTALLER: PLEASE LEAVE THESE INSTRUCTIONS WITH THE CONSUMER INSTALLATION INSTRUCTIONS PRESSURE ASSIST TOILETS Thank you for selecting Crane Plumbing Products. To ensure this product installs properly, please read these instructions carefully before you begin. Be sure your installation conforms to local codes. REMOVE OLD TOILET: Close toilet supply valve and flush the toilet. Sponge any remaining water from the bowl. Disconnect and remove supply line.
PAGE 2
4 NOTE: Check all connections for several days to detect any leaks which may develop. If they do, tighten all connections per instructions. Crane Plumbing, LLC is not responsible for leaking water connections. Also, after several days, remove the bolt caps from the bowl and tighten the nuts snugly. 10 Connect the cold water line to the tank with your straight or angle stop.
PAGE 3
Limited Lifetime Warranty on China / Limited One Year Warranty on Parts 10 Year Warranty on Pressure Vessel (See Manufacturers Owners Manual) Subject to the “Exclusions” set forth below, Crane Plumbing L.L.C. promises to the consumer to repair, or at the option of Crane Plumbing L.L.C.