OPERATOR'SMANUAL t_ Workbench 6' & 8' PART# F1725 Please indicate the following information from the service part drawing provided. Model Number: Model Description: *Product you purchased may vary from picture shown. Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product. Retain this document for future reference. Distributed by Sears Brands Management Corporation.
SAFETY WARNINGS AND CAUTIONS: • Use appropriate safety equipment damage. when using power and hand tools. Failure to do so may cause personal injury or product • Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product damage. • DO NOT stand on this product. You may fall which may cause personal injury. • DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
f STEP (3): STEP (1): AA(8) _ Assemble necessary EE(4) (2) (EE) in each (A). Some adjustments after workbench is in desired position. may be BB(8) _ cc(8) • Place workbench top (Purchased Separately), (D) with top side down. (Use packaging material to prevent scratches. Note: The rail (B) with the label should be placed toward the front of the unit with the label upside down. • Assemble (2) (A) and (2) (B), as shown, using (8) (AA), (8) (BB), and (8) (CO). Flanges of (B) should point in.
f J AA • • • • • • • BB CC Back Flanges point out Place the workbench in its upright position. Position (C) centered against back of workbench top (D), with flange underneath. Mark center of mounting hole locations using the holes in flange of (C) as a template. Make sure (C) does not move. Remove (C) for access. Drill 118"pi!otholes 1/2" deep in mounting hole locations. Repost'don(C) on workbench top (D). Attach using (DD). Flange underneath BB Square the unit and wrench tighten all fasteners.
M_NUAL DE USUARIO BANCO DE TRABAJO 6' & 8' S{rvase indicar la siguiente informacibn que encontrar_ en el dibujo suministradode la pieza de servicio. Nemero de modelo: Descripcibndel modelo: *La unidadque adquirib puede variar con respectoa la ilustracibn. Precaucibn: Lea y siga todas las reglas de seguridade instruccionespara el manejo antes de usar la unidad por primera vez. Conserve este manual para referenciafutura.
r ADVERTENCIAS Y PRECAUCIONES DE SEGURIDAD: • Utilice el equipo de seguridad adecuado cuando emplee herramientas el_ctricas. De Io contrario, podria causarle lesiones personales u ocasionar daSos al producto. • Utilice el personal adecuado para el montaje y el traslado de esta unidad. De Io centrario podrfa ocasionarse lesiones personales o daSar el producto. • NO se ponga de pie sobre la unidad. Podria caerse y lesionarse.
i l!!l I I f PASO (1): cc(8) AA(8) _ BB(8) • Coloque la parte superior del banco de trabajo (Comprada por sepal) (D) con el lado que tiene revestimiento hacia abajo (Utilice el marl del embalaje para evitar que se dafie) Nota: El lialguero (B) con la etiqueta debe colocarse hacia el frente de la unidad _ la etiqueta invertida EE(4) Ensamble (2) (EE) en cada (A). Puede que sean necesarios algunos ajustes despu_s de que el banco de trabajo est_ en la posicibn deseada.
i r #,-T I , AA • • BB Parte frontal • • CC • Parte trasera Las bndas est_n odentadas hacia afuera Coloque el banco de trabajo en su posicibn vertical. Coloque (C) centrado contra la parte superior posterior del banco de trabajo (:D)Con la bdda debajo. Marque el centre de la ubicacibnde agujeros de montaje utilizando los aguj_s en la brida de (C) como plantilla. Compruebe que (C) no se mue_.. Retire (C) para tener acceso.