Operator's Manual CRAFTSMAN 15 CU. FT. POLY CART DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 Model No. 486.24247 CAUTION: «= Safety Before using this product, read this manual and follow all Safety * Assembly Rules and Operating Instructions. «= Operation * Maintenance » Paris Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA. PRINTED IN U.S.A. FORM NO.
TABLE OF CONTENTS WARRANTY & SAFETY. 2 MAINTENANCE FULL SIZE HARDWARE CHART. SLOPE GUIDE... rei CARTON CONTENTS REPAIR PARTS ILLUSTRATION. ASSEMBLY. REPAIR PARTS LIST... OPERATION PARTS ORDERING/SERVICE. BACK PAGE 8 ae CRAFTSMAN LIMITED WARRANTY FOR TWO YEARS from the date of sale this product is warranted against defects in material or workmanship. WITH PROOF OF SALE a defective product will be replaced free of charge. For warranty coverage details to obtain free replacement, visit the web page: www.
FULL SIZE HARDWARE CHART REF | QTY. DESCRIPTION REF | QTY.
CARTON CONTENTS 1 Poly Tray 4. Latch Stand Bracket 7 Latch Lock Lever 2. Whee! Support 5. Draw Bar Tongue a. Hitch Bracket 3 Latch Stand Plate 6 Wheels (2) 9. Axle ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY (1) Phillips Screwdriver {1} Pliers (2) 7/16" Wrenches (2) 1/2" Wrench (2) 9/16" Wrenches STEP 1: {SEE FIGURE 1) Verify that all parts and all fasteners on pages 2 and 3 are included in the carton and parts bag.
STEP 2: (SEE FIGURE 2) Hank the short end of the spring (M) into the hole in the latch lock lever. Use the spring puller toot (P) to hook the long end of the spring into the square hole in the tongue. The spring puller tool can be stored when finished, FIGURE 2 STEP 3: (SEE FIGURE 3) Assemble the end of the hitch bracket (8) down through the slot at the front of the tongue.
STEP 6: (SEE FIGURE 8) Assemble the latch stand plate (3) and the latch * stand bracket (4) at the front of the tray using four hex bolts (C), washers {J) and hex nuts The aligning tab on the bottom of the latch stand bracket must be towards the rear of the Carl. Tighten. STEP 7: (SEE FIGURE 7) Place the tray onto the wheel support and position it so that the latch stand bracket locks into the latch lock lever. Fasten the tray to the whee! support using sight truss head bolts (D} and hex nuts (F). Tighten.
OPERATION Age CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. Realer to the vehicle owners manual for instructions on safe operation on slopes, Use the slope guide provided on page 11 of this manual to determine whether slope angle is foo steep 1.
SLOPE GUIDE {Keep this sheet in a safe place for future reference.) Use this guide to determine if a slope is safe for the operation of your tractor and cart. Refer also to the instructions in your vehicle owners manual.
eR RL REF. | PART NGUYEN OTY. DESCRIPTION 1 48608 1 Poly Tray 2 25106 1 | Whee! Support 3 24388 1 Latch Stand Plate 4 24487 1 | Latch Stand Bracket 5 24750 1 Tongue, Draw Bar 6 46272 2 | Wheel Assembly 7 24498 1 Latch Lock Lever 8 23014 1 | Hitch Bracket 9 248597 1 Axle, 1" 10 43088 4 Flat Washer, 1/4" ul 47407 1 Hex Bolt, 5/16" x 4° 12 47622 1 | spring Puller Tool 13 44488 4 | Wheel Bearing, 1" 14 43083 2 | Cotter Pin, 1/8" Dia.