Operator's Manual CRAFTSMAN’ Universal Bench-Top-Tool Adjustable Work Stand Model No. 320. 22335 + WARRANTY * SAFETY A CAUTION! Read, understand and = UNPACKING follow all Safety Rules and Operating + ASSEMBLY Instructions in this Manual before + DESCRIPTION using this product. + MAINTENANCE Sears Brands Management Corporation, Hoffman Estates, IL 60179 www.craftsmarn.
TABLE OF CONTENTS Warranty Page 2 Safety Symbols Page 3 Safety Instructions Pages 4-10 Unpacking Page 10 Description Page 11 Assembly Pages 1218 Maintenance Page 19 Parts list Pages 20-22 Sears Repair Parts Phone Numbers Back Cover ONE YEAR FULL WARRANTY ON CRAFTSMAN ® PROFESSIONAL PRODUCT If this Craftsman product fails due to a defect in material or workmanship within ane year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR PARTS AND REPAIR CENTER OR OTHER CRAFTSMAN OUTLET IN THE UNITED
SAFETY SYMBOLS The purpose of safety symbols is to attract you attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding, The symbol warnings do not by themselves eliminate any danger.
SAFETY INSTRUCTIONS A WARNING:Be sure to read, understand and follow all Safety rules and operating instructions in this Manual and the operator's manual of any bench top power tool you use with this Adjustable Work Stand. Failure to do so may result in electric shack, fire and for serous personal injury. WORK AREA SAFETY Keep work area clean and well lit. Cluttered and dark areas invite accidents.
Remove adjusting keys or blade wrenches before turning the tool "ON." A wrench that is left attached to a rotating part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Always secure your work, Use clamps or a vise to hold work when practical. lt is safer than using your hand and frees both hands to operate tool. Use safety equipment.
Use only accessories that are recommended for the tool being used. Accessories that may be suitable for one tool may become hazardous when used on another tool. ELECTRICAL SAFETY Grounded tools In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk electric shock. This stand is equipped with an electrical cord that has an equipment-grounding conductor and a grounding plug.
Use the proper extension cord. Make sure that your extension cord js good condition, When using an extension cord, be sure 10 use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in fine voltage resulting in loss of power and overheating. Minimum Gauge for Extension Cords Volts Total Length of Cord in Feet 120V 2511. 50ft. 100M. 150ft.
SAFETY FOR THE ADJUSTABLE WORK STAND Always set up the adjustable work stand on a hard, dry, flat, stable surface. Be sure that the adjustable work stand is fully opened and locked into the proper “set-up” position before mounting your bench-top power tool to the tabletop assembly. Follow all set-up instructions on pages 12 through 15 in this operator's manual.
Protect your lungs. Wear a face mask or dust mask if the operation is dusty. Protect your hearing. Wear appropriate personal hearing protection during use. Under some conditions, noise from power tools may contribute fo hearing loss, All visors and bystanders must wear the same safety equipment that the operator of the tool should wear, inspect the tool cords periodically and, if damaged, have them repaired at your nearest Sears Service Center. Be aware of the cord location.
Some examples of these chemicals are: * Lead from lead based paints. « Crystalline silica from bricks and cement and other masonry products, * Arsenic and chromium, from chemically treated lumber. Your risk from these exposures varies, depending upon how often you do this type of work.
DESCRIPTION This Adjustable Work Stand has the following features: 1. Setup adjustment handle with soft grip for easy setup and take down 2. Soft-grip dual handle for comfort during transport and sure grip during use 3. Locking pin support automatically engages to secure the stand when iris folded for storage. Compact design makes the adjustable work stand fordable for easy storage. Safety switch with duplex outlet, overload protection, and 10-ft. 8JT cable. Two, 4-in.
PRODUCT SPECIFICATIONS Stand Weight 50 Ibs. Maximum Weight Capacity 400 Ibs continuous load capacity Power Cord Length 10 ft, Tool Stand Height 28" 36” positive stops at 30", 32%, 34”, 38") Overall Dimensions, Fully extended (Wx36 in, (H) ASSEMBLY UNFOLDING AND SETTING UP THE WORK STAND 1. Remove the work stand from the carton and place it flat on floor, as shown (Fig. 2). 2.
3. With your foot still on the support bay, lift up the setup adjustment handle {Fig. 4). 4. With your foot still on the support bar, continue lifting the setup adjustment handle to the height desired. Make sure that the red lock knob on each side Is engaged. 5. With your foot still on the support bar and your hand on the setup adjustment handle to support the tabletop assembly, tighten the two red locking knobs to the maximum Inside position (Fig. 5). Fig.
NOTE: This work stand may be adjusted from: 287 36” in height with positive stops at 307,32", 34”, and 36”. To adjust the stands height, tum the two red locking knobs counter clockwise to unlock them, then pull out the left knob and follow steps 3-4, A prancer ale sure that your hand is always on the setup adjustment handle until the two locking knobs are locked In the holes.
8. 10. Be sure that, after adjusting the width of the tabletop assembly, you lock the four clamping knobs by turning them clockwise until securely tightened Fig. 9). Unlock the 4-inch locking Caster Wheels by lifting the locking lever on each wheel to the “UP” position (Fig. 10). Lock the Caster wheels in place by pushing the locking lever to the “DOWN “position Fig. 11). NOTE: When the work stand is on uneven surface, stabilize the stand by adjusting the adjustable foot (Fig.
ATTACHING YOUR BENCH-TOP TOOL TO THE STAND (Fig.12) A WARNING: Failure to es unplug the tool before attach. ing it to the stand could result in Mounting Holes accidental starting and possibly serious personal injury. A warning: To avoid serious personal injury, always make sure that bench tools are fully supported and securely attached to a level work surface. If necessary, move the stand to a location where it will be more stable.
SWITCH OPERATION The switch has a safety key to help prevent accidentally switching the tool ON and the unauthorized, possibly hazardous use by others, The safety key must be completely inserted into the switch before the switch panel can be turned ON. Two receptacles are located at the back of the switch assembly (Fig. 18. One is intended to supply power to your tool; the other can supply power to the a work light, vacuum cleaner, or other item. The ON/OFF switch panel controls power to both outlets.
3. To turn the power OFF, Fig 16 push the ON/OFF switch ; panel down (Fig. 16). 4. To lock switch in the OFF position, push the ON/ OFF switch panel down to OFF position, and remove the safety key from the switch panel. AA WARNING: Never leave a tool unattended while it is running or before it comes to a complete stop. Circuit Breaker When the switch-assembly current exceeds a safe level, it will overload the circuit, Circuit Breaker and the circuit breaker will Button trip.
MAINTENANCE This adjustable work stand has been designed to be low-maintenance. However, in order to maintain its performance, follow these steps. 1. Handle the adjustable work stand with care. Do not drop, throw, or otherwise mistreat the work stand. Use it only for its intended purpose. 2. Do not allow the adjustable work stand to become and remain wet, Keep it stored in a dry place. 3. In order to keep the adjustable work stand working properly, keep it clean.
GUE EE Universal Bench-Top-Tool Adjustable Work Stand MODEL NUMBER 320.22335 Always mention the Model Number when ordering parts for this tool.
[ERs Universal Bench-Top-Tool Adjustable Work Stand MODEL NUMBER 320.22335 Always mention the Model Number when ordering parts for this tool.
LIO200025 Alt MBX14mm 3 30 Lower Support Cover 4 31 LCOB00033 Left Block 1 32 LEO100026 Inner Bracket Assembly 1 33 110500022 Handle Spring 1 34 110200026 Flat Washer M8 16 35 Spring-loaded Locking 1 Pin Assembly 36 LB0200024 Pin 1 37 Rubber Support bar 2 38 LEC100027 | Support bar 1 39 110200027 Nut M& 34 40 LI0200028 Bolt MBX35mm 8 41 Rubber Foot 4 42 LI0200029 Washer 67 43 LIO200030 Axle Mexico 4 44 Right Block 1 45 LAQ200022 Angle Block 1 46 LI0200031 Bolt M8X25mm 2 47 Bush 8 48 LAO100023 Inner Bracket
Your Home For expert troubleshooting and home solutions advice: manage [fife home www.managemyhome.com For repair — in your home — of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.