INTRODUCTION Maintenance and Repair Instructions . . . . . . . . . . .12 TABLE OF CONTENTS Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7 Oil and Fuel Information . . . . . . . . . . . . . . . . . . . .
RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING Indicates danger, warning or caution. Attention is required in order to avoid serious personal injury.
RULES FOR SAFE OPERATION WHILE OPERATING • Never start or run the unit inside a closed room or building. Breathing exhaust fumes can kill. Operate this unit only in a well ventilated outdoor area. • Wear safety glasses or goggles that meet ANSI Z87.1 standards and are marked as such. Wear ear/hearing protection when operating this unit. Wear a face or dust mask if the operation is dusty. • Wear heavy, long pants, boots, gloves and a longsleeved shirt.
RULES FOR SAFE OPERATION SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING SYMBOL MEANING • THROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
KNOW YOUR UNIT Throttle Control Primer Bulb Handlebar Knob Muffler Starter Rope Grip Tine Guard Cultivator Tines 6 Handlebar
ASSEMBLY INSTRUCTIONS NOTE: Before setting up your cultivator / edger, disconnect the spark plug wire from the spark plug. ADJUSTING TINE DEPTH POSITIONING THE HANDLEBARS To adjust the wheel support bracket proceed as follows: 1. Stop engine and disconnect spark plug to avoid accidental starting. 1. Loosen the two knobs on the inside of the handlebars (Fig. 1). 2. Remove cotter pin from the clevis pin and slide clevis pin out of tailpiece bracket (Fig. 3). 2.
OIL AND FUEL INFORMATION Funnel Spout RECOMMENDED OIL TYPE Using the proper type and weight of oil in the crankcase is extremely important. Check the oil before each use and change the oil regularly. Using incorrect or dirty oil can cause premature engine wear and failure. Use a high-quality SAE 30 weight oil of API (American Petroleum Institute) service class SF, SG, SH. Fig. 5 ADDING OIL TO CRANKCASE: INITIAL USE NOTE: This unit is shipped without oil in the crankcase.
OIL AND FUEL INFORMATION RECOMMENDED FUEL TYPE Old fuel is the primary reason for improper unit performance. Be sure to use fresh, clean, unleaded gasoline. NOTE: This is a four cycle engine. In order to avoid damage to the unit, do not mix oil with gasoline. Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1% water in the fuel can make fuel form acids when stored.
STARTING/STOPPING INSTRUCTIONS ON (I) Operate this unit only in a well- ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. WARNING: OFF (O) WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 12). To avoid serious injury, the operator and unit must be in a stable position while starting. Throttle Control STARTING INSTRUCTIONS 1. Check the oil level in the crankcase. Refer to Checking the Oil Level. 2.
OPERATING INSTRUCTIONS OPERATING TIPS Dress properly to reduce the risk of injury when operating this unit. Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy long pants, boots and gloves. Do not wear short pants, sandals or operate barefoot. WARNING: 1. Move the cultivator to the work area prior to starting the engine. Transport the cultivator by pushing or pulling it along on its wheels.
MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by a Sears or other qualified service dealer. Call 1-800-4-MY-HOME® for more information. NOTE: Some maintenance procedures may require special tools or skills.
MAINTENANCE AND REPAIR INSTRUCTIONS 13
MAINTENANCE AND REPAIR INSTRUCTIONS AIR FILTER MAINTENANCE Cleaning the Air Filter Clean and re-oil the air filter every 10 hours of operation. It is an important item to maintain. Failure to maintain your air filter properly can result in poor performance or can cause permanent damage to your engine. 4. Apply enough clean SAE 30 motor oil to lightly coat the filter (Fig. 21). To avoid serious personal injury, always turn the unit off and allow it to cool before you clean or service it. WARNING: 1.
MAINTENANCE AND REPAIR INSTRUCTIONS NOTE: Ensure the tines are not in contact with the ground when adjusting the idle. 2. Release the throttle trigger and let the engine idle. If the engine stops, insert a small phillips or flat blade screwdriver into the hole in the air filter/muffler cover (Fig. 22). Turn the idle speed screw in, clockwise, 1/8 of a turn at a time (as needed) until the engine idles smoothly. 0.025 in. (0.635 mm.) NOTE: The tines should not rotate when the engine idles. 3.
MAINTENANCE AND REPAIR INSTRUCTIONS 7. Pull the starter rope slowly to bring the piston to the top of its travel, (known as top dead center). Check that: • The piston is at the top of its travel while looking in the spark plug hole (Fig. 27) • Both rocker arms move freely, and both valves are closed If these statements are not true, repeat this step. 8. Slide the feeler gauge between the rocker arm and the valve return spring. Measure the clearance between the valve stem and rocker arm (Fig. 29).
MAINTENANCE AND REPAIR INSTRUCTIONS Cleaning the Unit To avoid serious personal injury, always turn the unit off and allow it to cool before you clean or perform any maintenance on it. WARNING: • • Use a small brush to clean off the outside of the unit and to keep the air vents free of obstructions. Do not use strong detergents or petroleum based cleaners, such as kerosene. Some household cleaners contain aromatic oils such as pine and lemon that can damage the plastic housings or handles.
SPECIFICATIONS ENGINE* Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 4-Cycle Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 cu. in. (26.2 cc) Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES 21
NOTES 22
INTRODUCCION Instrucciones de operación . . . . . . . . . . . . . . . . .E11 INDICE DE CONTENIDOS Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E2 Instrucciones de mantenimiento y reparación . . .E12 Llamadas a apoyo al cliente . . . . . . . . . . . . . . . . . .E2 Limpieza y almacenamiento . . . . . . . . . . . . . . . . .E18 Normas para una operación segura . . . . . . . . . . . .E3 Cuadro de solución de problemas . . . . . . . . . . . .E19 Conozca su unidad . . . . . .
NORMAS PARA UNA OPERACION SEGURA Los símbolos de seguridad se utilizan para llamar su atención sobre posibles peligros. Los símbolos de seguridad y sus explicaciones merecen toda su atención y comprensión. Los símbolos de seguridad no eliminan ningún peligro por sí mismos. Las instrucciones o advertencias que ofrecen no substituyen las medidas adecuadas de prevención de accidentes. SIMBOLO SIGNIFICADO ALERTA DE SEGURIDAD: Indica peligro, advertencia o precaución.
NORMAS PARA UNA OPERACION SEGURA CUANDO ESTÉ OPERANDO • Nunca arranque ni opere la unidad dentro de un cuarto o edificio cerrado. Respirar los vapores del escape puede ser fatal. Opere esta unidad solamente en un área exterior bien ventilada. • Use gafas protectoras que cumplan con la norma Z87.1 de ANSI y tengan la marca que lo indica. Use protección para la oreja/audición cuando opere esta unidad. Use máscara facial o para polvo si la operación produce mucho polvo.
NORMAS PARA UNA OPERACION SEGURA SIMBOLOS DE SEGURIDAD DE INTERCACIONALES Este manual del operador describe los símbolos y figuras de seguridad e internacionales que pueden aparecer en este producto. Lea el manual del operador para obtener información completa acerca de la seguridad, ensamble, operación y mantenimiento y reparación. SIMBOLO SIGNIFICADO SIMBOLO • SIMBOLO DE ALERTA DE SEGURIDAD IIndica peligro, advertencia o precaución. Puede ser utilizado junto con otros símbolos o figuras.
CONOZCA SU UNIDAD Bombilla del cebador Mango de la cuerda de arranque 28
INSTRUCCIONES DE ENSAMBLE NOTE: Desde la posición de funcionamiento, se observa la referencia a la derecha o a la izquierda de la cultivadora / bordeadora. COLOCACIÓN DEL MANUBRIO 1. Afloje las dos perillas del lado interior del manubrio (Fig. 1). 2. Con la unidad en posición vertical, gire el manubrio hacia arriba hasta la posición de operación (Fig. 1). NOTA: Tenga cuidado de no pellizcar el cable del regulador o los cables del interruptor cuando coloque el manubrio. 3.
INFORMACION DEL ACEITE Y DEL COMBUSTIBLE Fig.
INSTRUCCIONES DE ARRANQUE Y APAGADO ENCENDIDO / ON Use esta unidad sólo en un área exterior bien ventilada. Los gases de escape de monóxido de carbono pueden ser letales en un área cerrada. ADVERTENCIA: APAGADO/ OFF Evite los arranques accidentales. Colóquese en posición de inicio cuando tire de la cuerda de arranque (Fig. 12). El operador y la unidad deben estar en una posición estable al arrancar la unidad para evitar graves lesiones personales. ADVERTENCIA: INSTRUCCIONES DE ARRANQUE 1.
INSTRUCCIONES DE OPERACION CONSEJOS PARA LA OPERACIÓN en ADVERTENCIA: Vista forma adecuada para reducir el riesgo de lesiones cuando opere esta unidad. No use ropa holgada ni alhajas. Use protección ocular y auditiva. Use pantalones largos y gruesos, botas y guantes. No use pantalones cortos, sandalias ni trabaje descalzo. 1. Mueva el cultivador al área de trabajo antes de arrancar el motor. Puede transportar el cultivador empujándolo sobre las ruedas o llevándolo del tubo central de la manija.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION NOTA: Algunos procedimientos de mantenimiento pueden requerir el uso de herramientas o habilidades especiales. Si no está seguro acerca de estos procedimientos, lleve su unidad a un establecimiento de reparación, persona o distribuidor de servicio autorizado que arregle motores para uso fuera de la carretera.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION INSPECCIÓN DEL NIVEL DE ACEITE Para evitar un desgaste excesivo del motor y el daño de la unidad, mantenga siempre el nivel de aceite correcto en el cárter del cigüeñal. No opere nunca la unidad con el aceite debajo del extremo inferior de la varilla de medición. No podemos exagerar la importancia de verificar y mantener el nivel correcto de aceite en el cárter del cigüeñal. Inspeccione el nivel de aceite antes de cada uso: 1.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION MANTENIMIENTO DEL FILTRO DE AIRE Limpieza del filtro de aire 4. Aplique suficiente aceite limpio de motor SAE 30 para recubrir ligeramente el filtro (Fig. 21). Limpie y vuelva a aceitar el filtro de aire cada 10 horas de operación. Es un elemento cuyo mantenimiento es importante. Si no realiza el mantenimiento del filtro de aire, su garantía será ANULADA.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION unidad ADVERTENCIA: La funcionará limpie PRECAUCION: No con chorro durante los ajustes del carburador. Use ropa que lo proteja y cumpla con todas las instrucciones de seguridad para prevenir graves lesiones personales. de arena, ni raspe ni limpie los electrodos. El motor podría dañarse si penetran pequeñas partículas en el cilindro. 2. Suelte el gatillo del regulador y deje que el motor funcione en marcha lenta.
HUELGO DEL BRAZO OSCILANTE El espacio libre del brazo oscilador pudiera necesitar ajuste si su unidad experimenta una pérdida de potencia de rendimiento o tiene problemas al arrancar. Para ajustar el espacio libre del brazo oscilador se requiere desarmar el motor. Si usted siente que no está seguro o que no está calificado como para realizar esto, lleve la unidad a un centro de servicio autorizado.
RESOLUCION DE PROBLEMAS 7. Tire lentamente de la cuerda de arranque para traer el pistón hacia la parte superior de su recorrido (conocido como punto muerto superior). Verifique que: • El pistón se encuentre en la parte superior de su recorrido mientras mira dentro del orificio de la bujía de encendido (Fig. 27). • Ambos brazos oscilantes se mueven con libertad, y ambas válvulas están cerradas De no ser así, repita este paso. 8.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION Limpieza de la Unidad evitar ADVERTENCIA: Para graves lesiones personales, apague siempre su unidad y espere que se enfríe antes de limpiarla o realizar cualquier tipo de mantenimiento. 2. Arranque el motor y déjelo funcionar hasta que se ahogue. Esto asegura que toda la gasolina se haya drenado del carburador. 3. Deje enfriar el motor. Saque la bujía de encendido y coloque 5 gotas de aceite de motor de buena calidad en el cilindro.
RESOLUCION DE PROBLEMAS EL MOTOR NO ARRANCA CAUSA El interruptor de encendido está APAGADO El tanque de combustible está vacío La bombilla del cebador no fue oprimida lo suficiente El motor se ha inundado La gasolina es vieja La bujía de encendido está sucia ACCION Mueva el interruptor a Encendido Llene el tanque de combustible Oprima la bombilla del cebador completa y lentamente 10 veces Hale el cordón de arranque repetidas veces con el control del obturador enteramente activado y con la palanca del estr
ESPECIFICACIONES MOTOR* Tipo de motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enfriado por aire, 4 ciclos Desplazamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26,2 cc (1.6 pulgadas cúbicas) Tipo de embrague . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS LIST Part Numbers On Following Page 43
PARTS LIST REPLACEMENT PARTS - MODEL 316.292711 4-CYCLE GAS CULTIVATOR Item Part No.
PARTS LIST 45
Repair Protection Agreements Convenios de Cobertura de Gastos para Reparaciones Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection Agreement can save you money and aggravation. Felicidades por haber hecho una compra inteligente.
Get it fixed, at your home or ours! Your Home For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME® (1-800-469-4663) Call anytime, day or night (U.S.A. and Canada) www.sears.