OPERATOR'S MANUAL 1/2 in., 19.2 VOLT CORDLESS DRILL-DRIVER VARIABLE SPEED/REVERSIBLE Model No. 315.115410 _, WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• Warranty ........................................................................................................................................................................... 2 • Introduction ...................................................................................................................................................................... 2 • General Safety Rules ......................................................................................................................
_ WARNING] • Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. • Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or pluggingin power tools that have the switch on invites accidents. • Remove any adjusting key or wrench before turning the power tool on.
• Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
_ WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS, Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. • Before using battery charger, read all instructions and cautionarymarkings in this manual, on battery charger, battery, and product usingbattery to prevent misuse of the productsand possible injuryor damage.
Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearntheirmeaning. Proper interpretation ofthesesymbols willallowyoutooperatethetoolbetterandsafer.
Thefollowing signalwordsandmeanings areintended toexplain thelevelsofriskassociated withthis product. SYMBOL SIGNAL MEANING _i, DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. ,_ WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicatesa potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
PRODUCT SPECIFICATIONS Chuck ........................................................... 1/2 in. Keyless Clutch ................................................................ 24 Position Motor ............................................................... 19.2 Volt DC Torque.................................................. Maximum 420 inJb. Switch .......................................................... Variable Speed Charger Input ...................................
KNOW YOUR DRILL-DRIVER See Figure 1. LED WORKLIGHT Beforeattempting to use this product, familiarize yourself with all operating features and safety rules. The LED worklight,located on the front of the tool base, illuminates when the switch trigger is depressed. This provides extra light for increased visibility. AUXILIARY HANDLE LEVELS Yourdrillis equipped with an auxiliaryhandle for ease of operation and to preventloss of control.
_, CHARGING WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious If battery pack is below normal temperature range, the green LED on charger wiMcome on. Allow battery pack to reach normal temperature, then the red LED will come on. injury. _i, WARNING: Always wear safety goggles or safety glasses with side shields when operating tools.
CHARGING A HOT BATTERY PACK TO INSTALL BATTERY PACK See Figure3. When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED. After 30 minutes, reinsert the battery pack in the charger.
_k WARNING: Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side. DIRECTION OFROTATION SELECTOR (FORWARD/REVERSE/ CENTER LOCK REVERSE To stop the drill, release the switch trigger and allow the chuck to come to a complete stop. NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right. Avoid running the drill at low speeds for extended periods of time.
KEYLESS CHUCK TODECREASE TORQUE See Figure 6. The drillhas a keylesschuck to tighten or release drill bits in the chuck jaws. The arrows on the chuck indicate which directionto rotate the chuck body in order to LOCK (tighten)or UNLOCK (release)the drill bit. _I, WARNING: 4_ ADJUSTINGRING Do not hold chuck bodywith one hand and use power of the drillto tighten chuck jaws on drillbit. Chuck body could slip in your hand or your hand could slipand come in contact with rotating drillbit.
BIT STORAGE See Figure 9. UNLOCK (RELEASE) DRILLBIT CHUCK COLLAR When not in use, bits provided with the drill can be placed in the storage area located on the base of the drill. SCREWDRIVER BIT CHUCK JAWS LOCK (TIGHTEN) CHUCK BODY STORAGE AREA RIGHT Fig. 10 Fig. 9 INSTALLING BITS See Figures I0.11. • Lock the switch triggerby placing the direction of rotationselectorin the center position.
ADJUSTING THE AUXILIARY HANDLE ASSEMBLY LEVEL See Figure 12. • Loosenthe auxiliaryhandle assembly by turningthe knobcounterclockwise. • Rotate the auxiliaryhandle assemblyto the desired location. • Tighten the auxiliaryhandle assemblysecurelyby turningthe knobclockwise. AUXILIARY TORQUE HANDLEASSEMBLYADJUSTMENT RING Fig. 13 • When drilling hard, smoothsurfaces, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off-center as the hole is started.
_lb MALLET WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. CHUCKJAWS WARNING: Always wear safety goggles or safety glasses with side shields when usingcompressed air to clean tools. If the operationis dusty, also wear a dust mask. _k WARNING: To avoid serious personal injury,always remove the battery pack from the toolwhen cleaning or performingany maintenance. HEXKEY CHUCK GENERAL MAINTENANCE Fig.
• Insert the hex key into the chuck and tighten the chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the spindle. It can now be unscrewed by hand. TO RETIGHTEN A LOOSE CHUCK The chuck may become loose on the spindle and develop a wobble. Also, the chuck screw may become loose, causing the chuck jaws to bind and prevent them from closing. To tighten: • Lock the switch trigger by placing the direction of rotation selector in the center position.
CRAFTSMAN 19.2 VOLT CORDLESS DRILL-DRIVER MODEL NO. 315.115410 (Item No. 11541) • J The model number will be found on a plate to the motor housing. Alwaysordering mentionrepair the model number in all correspondence regarding your attached CORDLESS DRILL-DRIVER or when parts. ] SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 4 6 PARTS LIST Key No. PaN Number Description 1 6613402 Screw (Special)....................................................................................
Get it fixed, at your home or ours! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® (1-800.469-4663) day or night (U.S.A. and Canada) www.sears.com www.
