Operator's Manual 3/8 in. 9.6 VOLT CORDLESS DRILL-DRIVER Variable Speed / Reversible Model No. 315.114050 Save this manual for future reference WARNING: Toreduce the risk of Injury, the user must read and understandthe operator's manual before usingthis product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www,sears.
• Warranty ......................................................................................................................................................................... 2 • Introducton..................................................................................................................................................................... 2 • General Safety Rules ......................................................................................................................
• 1, WARNING: Reed and understand all Instructions. Failureto follow all Instructionslistedbelow, may msuk in electric shock,fire and/or seriouspersonal Injury. Personal Safety • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while Urad or under the Influence of dregs, alcohol, or medication. A momentof inattentionwhile operatingpowertools may resultin serious personal injury. • Dress properly. Do not wear loose clothing or jewelry.
servlcad before using. Many acoidents are caused by poorly naintair_d teals. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be su_able for one tool, may create a riskof injury when used on another tool, Tool Use and Care • • • • • • • • Use clamps or other practical way to secure end support the workpisee to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Do not force tool.
• ThZ wire size Is large enough for AC ampere ral:lngof charger as specified below: _,WARNING: Never usa a battery that has been dropped or received a sharp blow. A damaged bakery Is subjectto explosion. Properlydispose of a dropped battery Immedla[ely.Failureto heed this warning can result in sedous personalInjury. • Before using battery charger, read all instructions and caofionew markings In this manual, on battery charger, and product using battew charger.
Important: Some of the followingsymbolsmay be used on your tool.Please studythem and leam their meaning. Proper interpretationof these symbolswill allow you to operate the tool better and safer. NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cyclesper second) mln Minutes Time AlternatingCurrent Type or a characteristicnf current = DireotCurrent Type or a characteristicof current no No Load Speed Rotational speed, at no load ...
Chuck 3/8In. Key'less Motor DC 9.6 Volt Gear Train Switch No Load Speed One Speed Vadable Speed O-600/min BATTERY PACK Item No. J11074 (976965-001) instructions Yourdrillhas been shippedcompletelyassembled. • Carefullyremove the tool and accessehes from the box. • Make sure that all Items listed In the pecking listare Included.
BIT STORAGE SCREWDRIVER BITS TORQUE ADJUSTMENTRING KEYLESS CHUCK ROTATION SELECTOR CHARGING STAND UGHT BATrERY CHARGER BATI'ERYPACK SHOWNINTOOL CHARGER See Figure I. S Fig.
IMPORTANT INFORMATION HOT BATTERY PACK WARNING: Do not aJtowfamiliaritywith your drilldriver to make you careless. Remember that a careless fraction of a second Is sufficientto Inflict severe Injury. When usingyour ddl[_dver continuously, the batteries in your battery packwill become hot. You shouldlet a hot bakery pack cooldown for approximately30 minutes before attempting to recharge. CHARGING BATTERY PACK See Figure 1.
TO INSTALL SWITCH See Figure 2. • To turnyour drillON, depress the switchtrigger. To turn it OFF, release the switchtrigger. • FORWARD/REVERSE SELECTOR BATTERY PACK Lockswitch triggeron your drillby placingthe direction of rotationselectorIn center position.See Figure 3, Place battery pack In your ddlLAlign raised db on battery packwith groove insideddlL See Figure3. BATI'ERY PACK VARIABLESPEED SWITCHTPJGGER Fig.
SWITCH LOCK See Figure 4, KEYLESS CHUCK See Figure 5. The switchtdgger can be locked In the OFF position.This feature can be used to prevent the possibilityof accldental startingwhen not in use. To lock switchtrigger, place the directionof rotationselector (Forward/ReverSeSelector) in center position. Yourdrillhasa k_=yless chuck. As the name Impites,you can handtightenor releasedrillbitsin the chuck J;tws.Graspand holdthe collarofthe chuck withone hand. Rotatethe chuck bodywithyourotherhand.
INSTALLING BITS See Figure 6. REMOVING BITS • Lock the switchtdgger by placing the directionof rotation selector In center position.See Figure 5, • Loekthe swltchtrigger by ptaolngthe directionof rotation selectorIn center position.See Figure 4, • Open or close chuck Jawsto a pointwhere the openIng Is slightlylarger than the bit size you Intend to use.
DRILLING BIT STORAGE See Figure 9, See Figure10. When not In use, bits provided with your drill can be placed In the storage arealocated on the bottomof your ddll as shown in Figure9. SCREWDRIVER BITS BITSTORAGE AREA Fig. lO When drillinghard smoothsurfaces use a center punch to mark desired hole location. This wlif preventthe ddll bit from slippingoff center as the hole Is started.However, the low speed feature allows staltlng holeswithoutcenter punchingIf desired.
CHUCK REMOVAL • See Figures 11,12, end 13. The chuck must be removed In order to use some accessodes. To remove: Insert hex key In chuck and tighten chuckjaws securely.Tap sharplywith a mallet in a counterclockwise direction,This will loosen chuck on the spindle. It can now be unscrewed by hand, See Figure 13, • Lockthe switchtdgger by placingthe directionof rotationselectorIn center position.See Figure 4, • Insert a 5/16 In.
_i Do not abuse power tools. Abusive practicescan damage tod as well as workplece. WARNING: When selvlclng, us=,only Identical Craftsman replacement parts. Use of any other pert may create a hazard or cause productdamage. Only the parts shownon parts list, page 16, are Intended to be repaired or replaced by the customer.
CRAFTSMAN 3/8in.,9.6VOLTCORDLESS DRILL-DRIVER - MODELNO.315.114050 In all correspondenceregarding your318In., 9.6 VOLT CORDLESS DRILL-DRIVER orwhen orderingrepair The modelnumberwillbe found on a plate attached tothe motorhousing.Alwaysrnentlon the modelnumber parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 \ 1 \ 4 \ PARTS UST Key No. 1 2 Part Number 660120002 Descd_lon Qty. Screw (Special) ...................................................................... 1 690033001 Chuck...........
II II IIII 17
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installationof home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800.469-4663) Call anytime, day or night(U.S.A, and Canada) www.sears.com www.sears.