Owner's Manual ICRRFTSMI:IN [ 318 in. DRILL-DRIVER Variable Speed / Reversible Double Insulated Model No. 315.101300 Save this manual future reference ,_ for CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer • Operation • Maintenance • Parts List Help Line: 1-800-932-3188 Sears Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
TABLE OF CONTENTS • Table of Contents ............................................................................................................................................... • General Safety Rules ..................................................................................................................................... 2-3 • Specific Safety Rules and/or Symbols ............................................................................................................
Tool Use and Care • Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. Additional Rules For Safe Operation Always wear safety glasses. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. Following this rule will reduce the risk of serious personal injury. Make sure your extension cord is in good condition.
SYMBOLS SYMBOL NAME DESIG NATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time ,-_ Alternating Current Type or a characteristic of current == Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load .../min Revolutions or Reciprocation Per Minute Revolutions, strokes, surface speed, orbits etc. per minute Indicates danger, warning or caution.
KNOW YOUR DRILL-DRIVER KEYLESS See Figure 1. Your drill-driverhas a keyless chuck that allows you to hand tighten or release drill bit in the chuck jaws. Before attempting to operate your drill-driver, familiarize yourself with all operating features and safety requirements. _L CHUCK SWITCH To turn your drill-driver ON, depress the switch trigger. Release switch trigger to turn your drill-driver OFF. WARNING: Carefully read through this entire owner's manual before using your new drill-driver.
PRODUCT APPLICATIONS SPECIFICATIONS: DRILL-DRIVER 315.101300 (Use only for the purpose listed below) 1/16 in. to 3/8 in. • Drilling in wood. Rating 120 V, 60 Hz, AC only • Input Switch 4.5 Amperes Drilling in ceramics, plastics, fiberglass, and laminates. Variable Speed • Drilling in both hard and soft metals. 0-1000 RPM • Using driving accessories, such as driving screws with screwdriver bits. • Mixing paints.
SWITCHLOCK LOCK (tighten) or UNLOCK (release) the chuck jaws. Grasp and hold the collar of the chuck with one hand. Rotate the chuck body with your other hand. Insert drill bit straight into the chuck the full length of the jaws, and tighten securely by rotating the chuck body in a clockwise direction. See Figure 3. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use.
,_, ADJUSTABLE WARNING: Make sure to insert drill bit straight into chuck jaws. Do not insert drill bit into chuck jaws at an angle and then tighten, as shown in Figure 5. This could cause drill bit to be thrown from drill, resulting in possible serious personal injury or damage to the chuck. TORQUE CLUTCH Your drill is equipped with an adjustable torque clutch for driving different types of screws into different materials.
BIT STORAGE ,_i See Figure 7. When not in use, bits provided with your drill can be placed in the storage area located on the top of your drill as shown in figure 7. BIT STORAGEAREA WARNING: Be prepared for binding or bit breakthrough. When these situations occur, drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when breaking through material. If not prepared, this toss of control can result in possible serious injury.
CHUCK REMOVAL TO RETIGHTEN A LOOSE CHUCK See Figure 9, The chuck must be removed in order to use some accessories. To remove: The chuck may become loose on the spindle and develop a wobble, • • ,_k To tighten, follow these steps: Unplug your drill, WARNING: Failure to unplug your drill could result in accidental starting causing serious injury. • Rotate torque adjusting ring to the maximum torque setting.
GENERAL DOUBLE All parts represent an important part of the double insulation system and should be serviced only at a Sears Service Center. Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. Avoid using solvents when cleaning plastic parts.
Thefollowingrecommended accessories arecurrentlyavailableatSearsretailstores. • HighSpeedBits(Forwoodor metal) 3/8 in. Max. • Doweling Jig (Item No._9-4186) • Masonry Bits • • ,_ 1/2 in. Max. • Drill Stand (Item No. _9-25989) Wood Boring Bits 1 in. Max. • Wire Brushes, All Hole Saws 1 in. Max. WARNING: The use of attachments or accessories not listed might be hazardous. WARRANTY FULL ONE YEAR WARRANTY ON rP.RFTSMRN 3/8 in. DRILL-DRIVER If this rRRFTSHRN 3/8 in.