Owner's Manual II:RRFTSMRN I 3/8 in. DRILL Reversible Double Insulated 315.101211 Model Nos. 315.101211 315.101221 315.101231 315.101221 Save this manual 315.101231 for • Safety • Features future reference _, CAUTION: • Operation • Maintenance • Parts List Readand follow all Safety Rules and Operating Instructions before first use of this product. Customer Sears, Help Line: Roebuck Visit the Craftsman 972000-795 9-00 1-800-932-3188 and Co., Hoffman Estates, IL 60179 web page: www.
• Table Of Contents .......................................................................................................................................... 2 • Warranty ......................................................................................................................................................... 2 • Introduction .....................................................................................................................................................
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL A MEANING SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
RULES FOR SAFE OPERATION WEAR PROPER APPAREL. (Continued) Do not wear loose MAKE SUREYOUR clothing or jewelry that can get caught in tool's moving parts and cause personal injury. Rubber gloves and nonskid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair and keep it from being drawn into nearby air vents. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. PROTECTYOUR LUNGS.
RULES FOR SAFE OPERATION (Continued) CHECK DAMAGED PARTS. Before further use • of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center.
Chuck: 101211 101221 101231 Capacity Horsepower Rating 3/8in.ChuckwithChuckKey 3/8in.ChuckwithChuckKey 3/8in.KeylessChuck 1/16in.to 3/8in. 1/3 120volts,60Hz,AConly,3.0AMPS NoLoadSpeed 1300RPM 101211 0 1300RPM 101221and101231 Switch: SingleSpeed/Reversible 101211 VariableSpeed/Reversible 101221 Adjustable VariableSpeed/Reversible 101231 Thefollowingrecommended accessories arecurrentlyavailableat SearsRetailStores. • HighSpeedBits(Forwoodor metal) 3/8in.Max. • Masonry Bits 1/2 in. Max.
KNOWYOURELECTRICDRILL APPLICATIONS See Figure 1. (Use only for the purpose listed below) Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. • Drilling in wood. • Drilling in ceramics, plastics, fiberglass, and laminates. • Drilling in both hard and soft metals. • Using driving accessories, such as driving screws with screwdriver bits. • Mixing paints. ELECTRICAL CONNECTION Your drill has a precision built electric motor.
MODEL 315.101221 VARIABLE SPEEDWITH3/8 in, CHUCK CHUCK LOCK-ON FORWARDREVERSELEVER CHUCK TOSTORE TO _HUCKKEY STORAGEAREA Fig, I (b) ii MODEL 315.101231 ADJUSTABLE VARIABLE SPEEDWITH3/8 in.
_IL WARNING: Your drill should never be connected to power supply when you are assembling parts, making adjustments, installing or removing drill bits, cleaning, or when not in use. Disconnecting your drill will prevent accidental starting that could cause serious personal injury. SWITCH See Figure 2. REVERSIBLE See Figure 3. Your drill has the feature of being reversible. The direction of chuck rotation is controlled by a lever located above the switch trigger.
counterclockwise to decreasethespeedandtorqueof yourdrill. If youdesireto lockthe switchonata givenspeed, depresstheswitchtrigger,pushinandholdthe lockonbutton,andreleasetheswitchtrigger.Next,adjust thevariablespeedcontrolselectoruntilthedesired speedis reached. Medium speed is suitable for drilling hard metals, plastics, and laminates. High speed produces best results when maximum power is required.
,_ WARNING: Do not hold chuck body with one hand and use the power of your drill to tighten the chuck jaws on your drill bits. The chuck body could slip in your hand or your hand could slip and come in contact with a rotating drill bit. This could cause an accident resulting in serious personal injury. TO INSTALL • On models 315.101211 and 315.101221 tighten chuck jaws securely, using only the chuck key provided. • On model 315.
REMOVING • ,_, • BITS When drilling metals, use a light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action. Unplug your drill. If the bit jams in workpiece or if the drill stalls, stop the tool immediately. Remove the bit from the workpiece and determine the reason for jamming. WARNING: Failure to unplug your drill could result in accidental starting causing serious injury. On models 315.101211 and 315.
CHUCK REMOVAL MODELS315.101211 AND315.101221 See Figure 10. The chuck must be removed in order to use some accessories. To remove: • Unplug your drill. _, WARNING: Failure to unplug your drill could result in accidental starting causing serious injury. • Insert a 5/16 in. or larger hex key into the chuck of your drill and tighten the chuck jaws securely. • Tap the hex key sharply with a mallet in a counterclockwise direction. See Figure 10. • This will loosen the chuck on the spindle.
,_ LUBRICATION WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. GENERAL EXTENSION CORDS Only the parts shown on parts list, page 15, are intended to be repaired or replaced by the customer.
CRAFTSMAN MODEL [ NOS. 315.101211 3/8 in. DRILL / 315.101221 / 315.101231 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 in. DRILL or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS SEENOTE"A" MODELS315.101211 AND 315.101221 1 3 MODEL315.101231 PARTS LIST Key No. Part Number Description Item 9-2975 Item 9-20988 Chuck (Model Nos. 315.101211 / 315.101221) ...............
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sMAnytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, day or night www.sears.