Operator's Manual CRAFTSMAN TWO BIN BEGGAR Model No. 247.240810 * Lifespan, P. 17 A CAUTION Before using this equipment, read this manual and follow ali safety rules and operating instructions. Sears Brands Management Corporation, Hoffman Estates, IL 80179, U.S.A. Visit our website: craftsmanship Form Ho.
TABLE OF CONTENTS Safe Operation Practices LL... 3 Slope GAUGE. ties 5 Contents of Carton & Hardware 6 Assembly and Installation 8 Operation iia 16 Lifespan. ooo 17 Service Numbers, ooh Back Cover CRAFTSMAN LIMITED WARRANTY FOR TWO YEARS from the date of sale this product is warranted against defects in material or workmanship. WITH PROOF OF SALE 4 defective product will be replaced free of charge.
SAFETY INSTRUCTIONS This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others, Read and folio all instructions in this manual before attempting to operate this machine.
SAFETY INSTRUCTIONS Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. Rapid engagement or braking could cause the front of the machine to lift and rapidly flip over backwards which could cause serious injury. Avoid starting or stopping on a slope. If rives lose traction, disengage the blade(s) and proceed slowly straight down the slope.
TT 100 Slope “710° Slope (OK) (TOO STEEP) Figure 1 Figure pee dashes line USE THIS SLOPE GAUGE TO DETERMINE SLOPE IS TOO STEEP FOR SAFE OPERATION! BE To check the slope, proceed as follows: po. Removes this page and fold along the dashed line. ha. Locate a vertical object on or behind the slope (e.g. a pale, building, thence. tees, afc) Align either side of the slope gauge with the object (Ses Figure 1 and Figure 2}. Adjust gauge up or down until the left corer touches the slope (See Figure 1 and Figure 2).
CONTENTS OF CARTON Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown below. Two hardware packs are included in this kit and are detailed on the following page. . Two Adhesive Foam Strips . Upright Support . Grass Catcher Cover . Chute Discharge Bracket . Chute Tube Extension Hitch Bracket Kit pes. 2 sided 7 cross mount. 2 wt mounts; . Flexible Tube Extension . Upper Chute Support . Upper Chute Tube .
CONTENTS OF CARTON CONTENTS OF HARDWARE PACK This grass collector Kit's shipped with three loose hardware packs enclosed and ohe set of hardware packed with the upright mounting bracket. Please check your hardware packs against the illustrations below. The quantities for each item Is listed in parenthesis.
ASSEMBLY AND INSTALLATION NOTE: References to left, right, front and rear of the tractor are from the operators Mowing Assembly on Tractor position, unless otherwise stated. Install mounting assembly on tractor as follows: Before assembly, place the tractor on a firm, level surface, disengage the Y ¥ PTO, stop the tractor engine and set the parking brake.
ASSEMBLY AND INSTALLATION 4. Install the upright support bracket onto the mounting assembly on the tractor 7. Snap the plastic upper chute support in place by first clipping the side by hooking it aver the mounting assembly as shown in Figure 4. portion onto the beggar support rail {1) with the edge of the snap feature aligned with the line on the label, as shown in the inset of Figure 5. \ Figure 4 5.
ASSEMBLY AND INSTALLATION 10. Clothespin other side of the screen by flexing the seen and pushing it down 12. Side the hinge pin info the hole located on the mounting tab, sin Figure 9. biretta the other corresponding cutout hole. See Figure 8. Use the cut-out window (See inset in Figure 10) to line up the hinge pinon the other side and push pin all the way in unt it beaches the end-stop. At this point the pin dips into place and is secured by a tab in the beggar cover. See Figure 11.
ASSEMBLY AND INSTALLATION 13. Open hood by pushing in on the rear, right-side tab with your right hand, as Assembling and Configuring the Discharge Chute seen tin of Figure 12, and sifting the cover with your left hand in the canter rear of the haggler cover, 2. Before installing the discharge chute onto your factor, some comports must first be assembled onto the upper chute, chi rte extension and discharge chute elbow. The following instructions for assembling and configuring the discharge chute: 1.
ASSEMBLY AND INSTALLATION 4. Install the upper chute tube info the wide end of the extension tube and 7 Apply the other wide adhesive rubber strip, included in Hardware Pack secured the tubes together using two {710-3013} hex screws and 712-0442 00342, onto the upper end of the discharge chute elbow. Place the adhesive cap dock nuts, included in hardware pack 689-00342. See Figure 16.
ASSEMBLY AND INSTALLATION Insert the end of the discharge chute elbow (2) into the hole provided in the 4. Insert the end of the discharge witted elbow (1) into the hole provided in the deck wheel mount as shown in the inset of Huger 19. deck wheel mount as shown in the inset of Figure 22. Pivot the discharge chute rearward until the hole in the discharge witted elbow aligns with the pinon the deck.
ASSEMBLY AND INSTALLATION 7. Install the upper chute tube onto the discharge chute elbow as shown in Install The Counter Weight Figure 24. The front weight kit is designed for use with all ORZO-L (Lap Bar) Residential Zero turn models. The front weight kit is NOT designed nor required for use with all RT-S (Steering Wheel) Residential Zero-turn models. WARNING! This front-weight kit is required when operating any compatible fap bar BET-L models equipped with a grass A collector.
ASSEMBLY AND INSTALLATION 2. Attach the weight bar assembly to the front axle with a 3% (710-3056) screw and (712-04063) flange nut from hardware pack 683-00325 on the left side. Repeat on the right side. Bo not fully tighten at this time. See Figure 27, Figure 27 3. Visually center the weight bar assembly on the tractor and tighten the hardware installed in step 2 10 secure the brackets to the front axle.
OPERATION Nagger Usage 4 NOTE: When both grass bags are full, place the tractor on a firm, level surface, disengage the PTO, turn the tractor engine off and set the parking brake. 1. Open the grass catcher hood by pushing in on the rear, right-side tab with your right hand, as seen in 1 of Figure 28, and lifting the cover with your left hand in the center rear of the beggar cover, 2. Figaro 28 2 Do not remove the site tube assembly from the tractor, 3.
INSTRUCCIONES DE SEGURIDAD A ADVERTENCIA La presencia de este símbolo indica que se trata de instrucciones importantes de seguridad que se deben respetar para evitar poner en peligro su seguridad personal yo material y la de otras personas. Lea y siga todas las instrucciones de este manual antes de poner en funcionamiento esta maquina. §i no respeta estas instrucciones podría provocar lesiones personales. Cuando vea este simbolismo.
INSTRUCCIONES DE SEGURIDAD 4. Siga las recomendaciones del fabricante sobre pesos contrapesos de las ruedas, para mejorar a estabilidad, 5, Haga que todas los movimientos en las pendientes sean fetos y graduales. No cambie repentinamente la velocidad ni la dirección. Un frenado o cambio de velocidad repentinos pueden causar que el frente de Ja maquina se levante y dé una voltereta hacia atrás, lo que podría causar lesiones graves.
10° Pendiente “TT 10° Pendiste (ACEPTAR) (DEMASIADO ESCARPADO) Figura 1 Figura linea gjg —_ Tt n tinge USO DE ESTE PENDIENTE DE CALIBRE PARA DETERMINAR UNA PENDIENTE ES DEMASIADO ESCARPADO PARA UNA OPERACIÓN SEGURA! Eo. — Para comprobar la pendiente, haga lo siguiente: pay 1. Borrar asía pagina y doble a lo largo de fa linea discontinua EE —" — Localizar un objeto vertical sobre 0 detrás de la pendiente {un poste, vn edificio, una valla, un &rol, ete} NE 2 3.
CONTENIDO DE LA CAJA Antes de comenzar la instalación, retire todas las plazas de 1a caja para asegurarse de que esté todo. Abajo se enumera y se muestra el contenido de la caja. Este Kit incluye dos paquetes de elementos de ferretera que se detallan en Ia pagina siguiente. . Dos franjas de espuma adhesiva . i Cubierta del colector de césped i . Extensión de tubo de canal . . Extensión de tubo flexible . Nube de canal superior : . Dos conjuntos de bolsas de césped . Conjunto de sapote de las bolsas : .
CONTENIDO DE LA CAJA CONTENIDO DEL PAQUETE DE ELEMENTOS DE FERRETERÍA Este equipo colector de césped se entrega con tres paquetes de elementos de ferretera sueltos y un paquete de elementos de ferretera con la ménsula de montaje vertical. Por favor controle el contenido de los paquetes de elementos de ferretera con las lustraciones siguientes. Las cantidades de cada elemento aparecen entre paréntesis.
MONTAJE E INSTALACIÓN NOTA: Las referencias a ezquerdeada, derecha, parte delantera trasera del tractor son Monte ef conjunto en el tractor desde la pusinesco del operador, silva indicativo en contraria. .
MONTAJE E INSTALACIÓN 4 Instale la ménsula de soporte vertical ende conjunto de montaje sobre ef 7 (Procesional el soporte del canal superior plastias coleando primero la tractor enganchándolo encima del conjunto de montare tal como se muestra porción lateral sobre ef car de soporte de la embolsad ara (1) con el horade figuradamente. que calza a presión alineado con la linea de la etiqueta, come se muestra en #f recuadro de fa Figura S. Plataforma de 50 guipadas Plataforma de 54 pulgadas Figura d 5.
0 MONTAJE E INSTALACIÓN Alee el otro lado de Ja pantalla flexionando la pantalla y empujándola dentro del otro orificio de abertura correspondiente . Yea la Figura 8. n Asegúrese de gue la pantalla ruede debajo del reborde de la cubierta Figura d instale fa cubierta de la embolsa dora en # conjunto de soporte de la balsa, come se muestra en la Fig. 9. La cubierta plástica va dentro de las dos lengüetas de montaje.
MONTAJE INSTALACIÓN 13. Abra el capta empujando hacia adentro la lengüeta posterior derecha con {amona derecha, como sebe en 1 dela Figura 12, levantando fa cubierta ona mano izquierda en ef centro de la parte posterior de la cubierta dela embalsamadora, 2.
MONTAJE E INSTALACIÓN 4 Instale el tubo del canal superior en el extreme ancho del tubo de extensión 7 Aplicártela franja de gamo adhesiva ancha, incluida en ef paquete de y fije fos tos hurtos usando dus tornillos hexagonales (710-3013) y cercas elementos de ferreteada 689-00342, en #l extrema superior del doce del de seguridad 712-0442, incluidos en of paquete de elementos de ferretera canal de descarga. Coligue la franja adhesiva antia contra el reborde ena 689-00342. Vea la Figura 16.
En las plataformas estampadas MONTANTEE INSTALACIÓN Inserte el extreme del codo def canal de descarga (2) en ef orificio 4 Inserte el extreme del codo del canal de descarga (1) en el definidor suministrado an el montaje de ruedo de la plataforma tal como se muestra suministrado en el montaje de roed de fa plataforma tal maco se muestra ene recuadro dela Figura 19. en el recuadro de (a Figura 22.
MONTAJE INSTALACIÓN 7 instale el who del canal superior en el doce del canal de descarga tal como se restar en fa Figura 24. Figura 24 8. Descubiertamente la embolsa dora alerta, gire ef tubo del canal superior en posición de manera tal que el canal se apoye en ef soporte del canal superior. Vea la Figura 25, Figura 25 NOTA: Sentires de alinear el canal superior con los rebordes del posarte del canal superior. 9. Hierve fa cubierto del colector de césped. 10.
MONTAJE E INSTALACIÓN 2 Sople el conjuro de barra de contrapeso al eje delantero con un torillo de 3-44" (710-3056) y tuerca con brida (712-0406% del paquete de elementos de ferretería 689-00325 del lado izquierdo. Repita lo mismo lada derecho. Bn este momento no apriete completamente.
FUNCIONAMIENTO Usa de la embolsa dora 4 HATO: Una vez que estén llenas ambas bolsas recolectoras de césped, coligue ef tractor en suelo firme y nivelada, desactive fa PTO, apague ef motor def tractor y ponga el freno de mano. 1 Abra el capad del colector de copes rempujada hada adentro la lengüeta posterior derecha nocla mano derecha, comes ve en Tde la Figura 28,y levantando la cubierta con 1a mano izquierda en ef centro de la parte posterior dela cubierta de la embolsad ara, 2.