Operator's Manual CRAFTSMH 12-in. DRILL PRESS 1/2 HP MOTOR Model 124.34985 CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions. ® Safety Instructions ® Assembly ® Operation • Maintenance • Troubleshooting ® Parts List • Espa_ol Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.
Warranty .......................................................................................................................................................................................... Safety Instructions ..................................................................................................................................................................................... Specifications ...................................................................................................
17. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. 18. CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.
BASE - Supports drill press. For additional stability, holes are provided in base to bolt drill press to bench. BACKUP MATERIAL - A piece of scrap wood placed between the workpiece and table. The backup board prevents wood in the workpiece from splintering when the drill passes through the backside of the workpiece. It also prevents drilling into the table top. HEAD ASSEMBLY - Covers the pulleys and belt during operation of the drill press.
ELECTRICAL REQUIREMENTS POWER SUPPLY AND MOTOR SPECiFiCATiONS WARNING: To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection. Use a separate electrical circuit for your tools. To avoid shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately. GROUNDING iNSTRUCTiONS WARNING: This tool must be grounded while in use to protect the operator from electrical shock.
CARTON CONTENTS UNPACKING AND CHECKING CONTENTS Carefully unpack the Drill Press and all its parts, and compare against the illustration following. WARNING: • To avoid injury from unexpected starting, do not plug the power cord into a power source receptacle during unpacking and assembly. This cord must remain unplugged whenever you are assembling or adjusting the drill press.
B. Accessories (in one separate box) See Fig.2 B. Crank handle C. Hex wrenches D. Feed Hex bolts A. handles E. Chuck key F. 5/8=inch Chuck and chuck removal tool G Table fence set I I I _/_ C A D B E F Table Fence Use the supplied hardware to attach the fence to the table as shown in the picture below. Use the fence to align the workpiece and provide a backstop for secure drilling. NOTE: Table pictured is different shape than equipped with product.
1. Column support to base 1.1 Position the base on floor or bench. 1.2 Place the column on the base, aligning the holes in the column support with the holes in the base. 1.3 Locate the four long hex bolts from the loose parts bag. 1.4 Place a bolt in each hole through the column support and the base. Tighten with an adjustable wrench. See Fig. I 2. Installing the Table 2.1 Loosen set screw (1). Remove rack (2) and retaining ring (3) from column (4). Fig. 2A 2.
5. Installing the chuck WARNING: Before any assembly of the chuck and arbor to the drill press head, clean all mating surfaces with a non-petroleum based product; such as alcohol or lacquer thinner. Any oil or grease used in the packing of these parts must be removed; may come loose during operation. otherwise the chuck 5.1 Open the jaws of the chuck by rotating the chuck sleeve clockwise. To prevent damage, make sure the jaws are completely receded into the chuck.
1. Table adjustment A. Tilting adjustment - On underside of table support bracket, back out set screw with supplied hex wrench, Loosen large hex head bolt, See Fig, 9 - Rotate table to desired angle right or left. Use bevel scale for precise setting, See Fig, 10 - Tighten hex head bolt to secure table tilt. Set screw should not be tightened when table is tilted, Figure 9 Figure 10 Figure 11 Figure 12 - To return table to level, loosen large hex head bolt. Rotate table to level position.
WARNING: To prevent personal injury, always disconnect the plug from the power source when making any adjustment. 2. Feed Depth Adjustment The depth gauge is located on the feed handle hub. Use the depth gauge to accurately and consistently set the required drilling depth. Loosen the depth stop fixing screw, set the depth stop as required and subsequently re-tighten the fixing screw. 3.
6. ADJUSTING THE LASER LINE NOTE: Laser pointer (1) is an alternative part. Your machine may not have this laser pointer. How to check and adjust the Laser Beam Alignment: Check the laser beam alignment to ensure the intersection of the laser lines precisely at the spot where the drill bit meets the workpiece. If it is not, the laser lines should be adjusted using the laser adjustment knobs located on the opposite sides of the head assembly. See Fig. 16 1. Mark an "X" on a piece of scrap wood. 2.
1. Installing A Drill Bit See Fig. 16 1.1. With the switch "OFF", open the chuck jaws (1) using the chuck key (2). Turn the chuck key counterclockwise to open the chuck jaws (1). 1.2. Insert the drill bit (3) into the chuck far enough to obtain maximum gripping by the jaws, but not far enough to touch the spiral grooves (flutes) of the drill bit when the jaws are tightened. 1.3. Make sure that the drill is centered in the chuck. 1.4. Turn the chuck key clockwise to tighten the jaws.
Correct Drilling Speeds WARNING: Be sure drill press is turned off and is disconnected Use the recommended speed for the drill bit and workpiece. The drill bits that can be used are shown in following figure: from power sours before adjusting speeds.
MAiNTAiNiNG YOUR DRILL PRESS LUBRICATION All of the drill press ball bearings are packed with grease at the factory, They require no further lubrication, Lower spindle to maximum depth and oil moderately once every three months. WARNING: For your own safety, turn the switch OFF and remove the plug from the power source outlet before maintaining or lubricating your drill press. Frequently blow out any dust that accumulates inside the motor with an air compressor or dust vacuum.
Cb 67_-- 88- 10__ '\,7 2 16
KEY NO. MFG. PART NO. QUANTITY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 24-1 24-2 24-3 24-4 24-5 24-6 24-7 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41-1 41-2 41-3 41-4 41-5 41-6 41-7 41-8 41-9 41-10 41-11 41-12 41-13 42 43 44 45 46 47 48 49 Retaininq ring Strain relief Retaining ring _ear!ng _eanng Retaining rin.
KEY NO. 50 51 52 53 54 54-1 54-2 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88-1 88-2 88-3 88-4 88-5 88-6 88-7 88-8 88-9 88-10 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 MFG. PART NO.
Repair Protection Agreements Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation.
Garantia ............................................................................................................................................................................. Las instrucciones de seguridad ................................................................................................................................... Especificaci6ns ..................................................................................................................................... Seguridad ......
17. Nunca se pare SOBRE LA HERRAMIENTA. Lesiones graves pueden ocurrir si la herramienta se inclina o si la herramienta de corte involuntariamente contactados. 18. DISPONER DE PARTES daSadas.
NECESIDADES FUENTE DE ENERGiA DE ALIMENTACI6N ELECTRICA Y ESPECIFICACIONES DEL MOTOR ADVERTENCIA: Con et fin de evitar riesgos etectricos, de incendio, o dafios a la herramienta, utilice una adecuada protecci6n contra cortocircuitos. Utitizar un circuito etectrico separado para sus herramientas. La taladradora esta inmovitizada en la fabrica de 115V. Conectar a 115V, circuito de 15 amperes y utitizar un retardo de 15 amperes fusibtes ou.
VELOCIDAD GUiAS BASE -Apoya drill press. Para obtener m_s estabilidad, tiene cuatro orificios en la base para perno perforaci6n presione al tribunal. MATERIAL DE COPIA DE SEGURIDAD - Un pedazo de madera de desecho colocado entre la pieza y el cuadro. La copia de seguridad impide junta madera en la pieza de astillamiento cuando el taladro pasa a trav6s de la parte trasera de la pieza de trabajo. Tambi6n evita la perforacidn en la parte superior de la mesa.
EL CARTON CONTENIDO DESEMBALAJE y comprobaci6n CONTENIDO Desemb_lelo cuidadosamente la Taladradora y todas sus piezas, y comparar contra la ilustraci6n siguiente. ADVERTENClA: • Para evitar dafios en caso de partida inesperada, no conecte el cable de alimentaci6n a una fuente de alimentaci6n recipiente durante desembalaje y el montaje. Este cable debe seguir siendo desconectado cuando se est_n reuniendo o ajustar la taladradora.
B. Accesorios (en un recuadro aparte) See Fig.2 B. C. D. A. E. Manivela Una Ilave hexagonal Tornillo Hexagonal Piensosmanejar Chuck clave I I l C F. Chuck G Tabla valla A B E D F Tabla Valla Usar el hardware para adjuntar la valla para ta tabta como se muestra en ta imagen de abajo. Utitice la valla para alinear la pieza de trabajo y proporcionar un apoyo seguro de perforaci6n. NOTA: La tabta que se ve es diferente forma de equipados las ranuras de la misma manera. con et producto.
1. La columna apoyo a base 1.1 Posici6n la base en el piso o banqueta. 1.2 Colocar la columna de la base, alineando los orificios en la columna soporte con los orificios en la base. 1.3 Busque los cuatro pernos hexagonal largo piezas sueltas de la bolsa. 1.4 Colocar el tornillo en cada agujero a trav6s de la columna so porte yen la base. Apriete con una Ilave ajustable. See Fig. 1 2. Instalar la mesa 2.1 Afloje tornillo de ajuste (1). Quitar rack (2) y anillo de retenci6n (3) en la columna (4). Fig. 2A 2.
5. Instalando el chuck ADVERTENCIA: Antes de cualquier reuni6n del mandril y arbor al drill press jefe, limpie todas las superficies con un apareamiento sin petr61eo producto; tales como el alcohol o thinner. Cualquier aceite o grasa utilizada en el envase y embalaje de estas partes deben ser eliminados; de Io contrario el portabrocas puede desprenderse durante la operaci6n. 5.1 Abra las quijadas del chuck por rotaci6n de la chuck manga las manecillas del reloj.
1. Ajuste "labia A. Inclinaci6n - En la parte inferior del cuadro escuadra de soporte, de vuelta de tornillo suministrados con una Ilave hexagonal. Afloje gran tornillo de cabeza hexagonal. See Fig, 9 - Rotar tabla a _ngulo deseado derecha o la izquierda. Utilice escala de bisel de ajuste preciso. See Fig, 10 - Apriete tornillo de cabeza hexagonal para garantizar mesa basculante. Tornillo de ajuste no debedan ser m_s estrictos cuando tabla est_ inclinado.
ADVERTENClA: Para evitar lesiones personales, siempre desconecte el cable de la fuente de energia para realizar cualquier tipo de ajuste. 2. Alirnentar Ajuste Profundidad El tope de profundidad se encuentra en los piensos manejar hub. Utilice el tope de profundidad para establecer con precisi6n y coherencia la necesaria profundidad de perforaci6n. Afloje el tornillo de fijaci6n profundidad detener, establezca la profundidad parar cuando sea necesario y posteriormente apretar el tornillo de fijaci6n. 3.
1. Instalando una broca See Fig. 13 1.1. Con el interruptor "OFF", abrir el chuck mandibulas (1) usando el chuck clave (2). Gire el chuck clave las agujas del reloj para abrir el chuck mandibulas (1). 1.2. Inserte la broca (3) en el chuck Io suficiente para obtener el m&ximo agarre de las mandibulas, pero no Io suficiente para tocar el espiral surcos (fiautas), de la broca cuando las mandibulas se estrechan. 1.3. AsegOrese de que el taladro est_ centrada en la broca. 1.4.
4. Corregir la perforaci6n velocidades ADVERTENCIA: aseg_rese de prensa perforadora est_ apagada y est_ desconectada velocidades. Utilizar la velocidad recomendada para la broca y pieza.
IVlANTENER LA LUBRICACION. LA TALADRADORA Toda la prensa perforadora rodamientos de bolas est_n Ilenos de grasa en la Mbrica. No es necesario dar mayores la lubricaci6n. Eje inferior a profundidad m_xima y moderadamente aceite una vez cada tres meses. ADVERTENCIA: Por su propia seguridad, apague el interruptor y quitar el conector de la fuente de energia antes del mantenimiento o lubricaci6n de la taladradora.
REPARAR ACUERDO DE PROTECCION Felicitaciones por hacer una compra inteligente. Su nuevo producto Craftsman® esta disefiado y fabricado por afios de funcionamiento confiable. Pero al igual que todos los productos, podFa exigir reparaci6n de vez en cuando. Es entonces cuando habiendo una reparaci6n acuerdo de protecci6n le puede ahorrar dinero y a la agravaci6n. Esto es Io que la reparation acuerdo de proteccion * incluye: [] Servicio de Expertos por nuestros 10.
Your Home For troubleshooting, product manuals and expert advice: www.managemylife.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.
