Sears owners manual MODEL NO, 113.22560 Serial Number Mode! and serial number may be found on the right side of the base. You should record both model and serial number in a safe place for future use. CAUTION: Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS carefully | CRAFTSMAN. INCH SANDER GRINDER e assembly e operating e repair parts Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A. Part No.
Stat” FULL ONE YEA WARRANTY ON CRAFTSMAN 1 INCH SANDER/GRINDER 1 within e year: (rom the: date of purchase this Craftsman 1 inch fiats due to a defect in material or workmanship, Sears will repair it, frats of charge : WARRANTY. SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES. This warranty gives vou merciful mega! rights, and you may also have other rights which vary fmm state to SEARS, ROEBUCK AND) CO.
ADDITIONAL SAFETY INSTRUCTIONS FOR SANDER/GRINDER WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR SANDER/GRINDER UNTIL 1T IS COMPLETELY ASSEMBLED ACCORDING FO THE INSTRUCTIONS, ‘AND THAT YOU UNDERSTAND THE FOLLOWING {SEE CONTENTS PAGE 3} . Generator safety Instructions for Power Roofs (Page 2) Getting 10 Know Your Sander/Grinder {Page 5) . Basic Sander/Grinder Operations (Page 6) Maintenance (Page 8) a Open s Power Source Outlet.
AND E ; . Moron specification ~ The' AL Monetarism Spit Phase non-reversible types, nth the L growing < Horsepower At though | the motorist designed fcr soprano on the voltage and.: frequency. specified o mortar. nameplate, normal loads will be handed safely’ on voltages not more teary 0% above or below the nameplate voltage.
ASSEMBLY Your Craftsman Sander/Grinder is shipped complete including the mortar, The Duse Sanding attachment and Miter Gauge are optional accessories. WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED, The top arm s spring loaded and held down for shipping purposes with 8 piece of cord. Hold down against spring pressure on the arm, remove the cord and ease up on the arm. Apply a coat of automobile wax to the table.
~ GETTING TO KNOW YOUR SANDER/GRINDER upper TRACKING SCREW gypper GUARD ARg UPPER WHELK LOWER . DIRECTIONAL W AR RACKING SCREW TABLE LOCK NUT nicks: table in-place. Use & square or protractor to adjust table (o desired angle to belt, TRACKING SCREWS are adjusted to track belt. : . IDLER ARG TABLE ADJUSTING SCREWS BACK GIRD {EF TAME REAR IDLER ON-OFF SWITCH WITH BOVINE FOR FLECKING.
GRINDING METAL H Move the workplace across the belt f the work piece becomes too hot to handle, quench it in cold water, Never push a sharp corner of the work piece rapidly against the blat because the belt could tear. INSIDE WORK WARNING: FOR YOUR OWN SAFETY, REMOVE PLUG FROM POWER SOURCE HUNTLEY. 1. Remove both “"Upper” and Lower’” guards. 2. Loosen wing nut and position guard back as shown. 3. Remove the “Hairpin Clip” which retains the rear idler, Use a pair of long nose pliers.
SHARPENING NOTCH 0N 1 Adjust table to. proper angular ‘position’ for' intended CAPEK OF WOOD operation, Lock measureless 0 ‘20 \When _sharpening. short: catting tools. site & 'wood chisels, it will be: necessary 10 clamp a piece of owed o the table. a3 5 notch on the back of the wood so that the top comer is close 1o the belt. 4. Move..the cutting tool across the belt, pushing on It gently 50, that it dded ot burn. 5. Frequently. quench the cutting tool in water to keep it cool, POLISHING .
RECOMMENDED ACCESSORIES DISC SANDING ATTACHMENT < 822563 STEEL STAND ...v.iooivuneiinnn veteran 822219 MITER GAUGE (FOR USE WITH 9-22563) . .« §-22574 POWER TOOL KNOW HOW "HANDBOOKS” ABRASIVE BELTS 17 x 427 TABLE SAW [T Racer. 92018 GENE . covenant . 926066 RADIAL SAW .. . 82017 MEDIUM . 9.26055 The above recommended accessories are current and were COARSE reeve .
Sears owners INCH SANDER GRINDER manual SERVICE Now that you have purchased your 1-inch sander grinder, should a need ever exist for repair or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit, MO DEL NO. Thehmo(zéei of your 1-inch sander grinder will be found on the side of the base. 113.