Operator’s Manual 9 Amp/1.5 Peak HP Motor Electric Adjustable Pole Saw/Chain Saw Model No. 172.43983 10-In. Bar Chain Saw with extension pole (shown separated) CAUTION: Read, understand and follow all Safety Rules and Operating Instructions in this Manual before using this product.
SAFETY SYMBOLS TABLE OF CONTENTS Warranty……………………………..........................................……………..Page 2 Safety Symbols……………………..........................................……………..Page 3 Safety Instructions……………………..........................................……….....Pages 4 - 13 Unpacking..……………………………...........................………………….....Page 13 Description………………………………..........................................………..Pages 14 - 15 Assembly and Adjustments………………………………..............................
SAFETY INSTRUCTIONS ! SAFETY INSTRUCTIONS cont. WARNING: If correctly used, this electric Pole Saw/Chain Saw is an efficient tool to use; if used improperly or without the due precautions it could become a dangerous tool. For pleasant and safe work, ALWAYS strictly comply with the safety rules that are contained in this manual. ! WARNING: BE SURE to read and understand all instructions in this manual before using this electric Pole Saw/Chain Saw.
SAFETY INSTRUCTIONS cont. ELECTRICAL SAFETY ! WARNING: Do not permit fingers to touch the terminals of plug when installing or removing the extension cord from the plug. 1. Double insulated tools are equipped with a polarized plug (one blade is wider than the other and will require the use of a polarized extension cord. The Chain Saw’s plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug.
SAFETY INSTRUCTIONS cont. SERVICE SAFETY 1. If any part of this Pole Saw/Chain Saw is missing or should break, bend, or fail in any way; or should any electrical component fail to perform properly: SHUT OFF the power switch and remove the power cord from the Chain Saw and have the missing, damaged or failed parts replaced BEFORE resuming operation. 2. Tool service should be performed at a qualified service dealer or repair center.
SAFETY INSTRUCTIONS cont. ADDITIONAL RULES FOR SAFE OPERATION cont. 4. Wear safety glasses and hearing protection. Further protective equipment for head, hands, legs and feet is recommended. Adequate protective clothing will reduce personal injury by flying debris or accidental contact with the saw chain. 5. ALL VISITORS AND BYSTANDERS MUST wear the same safety equipment that the operator of the tool wears. 6. ALWAYS check the tool for damaged parts.
ADDITIONAL RULES FOR SAFE OPERATION cont. SAFETY INSTRUCTIONS cont. ADDITIONAL RULES FOR SAFE OPERATION cont. SAFETY INSTRUCTIONS cont. MAINTAIN CONTROL (When using Chain Saw without Pole) KICKBACK SAFETY FEATURES cont. 4. Low Kickback Chain has met kickback performance requirements when tested on the representative sample of these chain saws specified in ANSI B175.1. See Fig. B, pg.12.
DESCRIPTION DESCRIPTION cont. KNOW YOUR CHAIN SAW KNOW YOUR CHAIN SAW cont. CHAIN SAW CALL- OUTS cont. (Figures 1 and 2) NOTE: Before attempting to use this product, familiarize yourself with all operating features and safety rules. Fig 1. Your Chain Saw has a precision built electric motor and it should only be connected to a 120-volt, 60 Hz AC ONLY power supply (normal household current). The electric Pole Saw/ Chain Saw should always be used with a GFCI (Ground Fault Circuit Interrupter) outlet.
ASSEMBLY & ADJUSTMENTS ASSEMBLY & ADJUSTMENTS cont. INTENDED USE The pole saw/chain saw is intended for wood: sawing of trees, tree trunks, branches, wooden beams, planks, etc. Cuts can be sawed with or across the grain. This product is not suitable for sawing mineral materials, plastics or non-wood building materials. ASSEMBLY ! WARNING: Do not connect the chain saw to extension cord and power source before it is completely assembled. Always use gloves when handling the chain.
ASSEMBLY & ADJUSTMENTS cont. ASSEMBLY & ADJUSTMENTS cont. LUBRICATION ! CAUTION: The chain saw is NOT supplied filled with oil. It is essential to fill with oil before use. Never operate the chain saw without chain oil or at an empty oil tank level, as this will result in extensive damage to the product. Chain life and cutting capacity depends on optimum lubrication.
OPERATION cont. ASSEMBLY & ADJUSTMENTS cont. CUTTING WITH CHAINSAW ADJUSTING POLE LENGTH The pole saw has a telescoping pole assembly that will extend from 89.7 inches (fully retracted) to 119.4 inches (fully extended). ! IMPORTANT: Be sure the oil reservoir is filled. Check the Oil Level Window (see Fig. 11) prior to starting and regularly during operation. Refill oil when oil level is low. A full oil tank will last approx. 12 minutes depending on sawing intensity and stops.
OPERATION cont. OPERATION cont. CUTTING WITH CHAINSAW cont. KICKBACK SAFETY DEVICES ON THIS SAW (see also pages 10 and 11 for details) This saw has a low-kickback chain and reduced kickback Guide Bar. Both items reduce the chance of kickback. However, kickback can still occur with this saw. The following steps will reduce the risk of kickback. • Use both hands to grip saw while saw is running. Use firm grip. Thumbs and fingers must wrap around saw handles. • Keep all safety items in place on saw.
OPERATION cont. CUTTING WITH CHAINSAW cont. OPERATION cont. CUTTING WITH CHAINSAW cont. INSTRUCTIONS CONCERNING THE PROPER TECHNIQUES FOR BASIC FELLING, LIMBING, AND CROSS-CUTTING (see Figures A, B, C, D, E and F) cont. INSTRUCTIONS CONCERNING THE PROPER TECHNIQUES FOR BASIC FELLING, LIMBING, AND CROSS-CUTTING (see Figures A, B, C, D, E and F) cont. 3. Felling back cut cont. As the felling gets close to the hinge, the tree should begin to fall. Bucking a log cont. Fig. A.
OPERATION FOR POLE SAW OPERATION FOR POLE SAW cont. Cutting with extension pole 1. Connect saw to extension cord. Connect extension cord to power supply. Before cutting a high branch, consider all the same points detailed in the previous section but pay particular attention to the likely path of the falling branch. ! WARNING: Do not stand directly below a branch being cut. Keep bystanders far away. Do not stand on a ladder or other type of unstable support while using the tool.
MAINTENANCE AND STORAGE OF CHAIN SAW cont. MAINTENANCE AND STORAGE OF CHAIN SAW cont. 3. Maintain chain saw with care. • Never expose saw to rain. • Keep chain sharp, clean, and lubricated for better and safer performance. • Follow steps outlined in this manual to sharpen chain. • Keep handles dry, clean, and free of oil and grease. • Keep all screws and nuts tight. • Inspect power cord often. If damaged, have repaired by authorized service center. • Never carry chain saw by power cord.
Check power Use another socket Check cord, replace Chain saw operates intermittently Extension cord damaged Loose connection Internal wiring defective On/Off defective Check cord, replace Contact service agent Contact service agent Contact service agent Dry chain No oil in reservoir Vent in oil filler cap clogged Oil passage clogged Refill oil Clean cap Clean oil passage outlet Chain /chain bar overheats No oil in reservoir Vent in oil filler cap clogged Oil passage clogged Chain is over tensioned Dull c
65 66 67 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 101 102 103 104 120 121 122 Position No. GCS250U-65 GCS250U-66 GCS250U-67 GCS250U-69 GCS250U-70 GCS250U-71 GCS250U-72 GCS250U-73 GCS250U-74 GCS250U-75 GCS250U-76 GCS250U-77 GCS250U-78 GCS250U-79 GCS250U-80 GCS250U-81 GCS250U-82 GCS250U-83 GCS250U-84 GCS250U-85 GCS250U-101 GCS250U-102 GCS250U-103 GCS250U-104 GCS250U-120 GCS250U-121 GCS250U-122 Parts No. Model No. 172.43983 10-In. Bar Qty.
