READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Beckham Installation Guide For Model: BEK54 Table of Contents: WARNING DC Motor will not operate until blades are installed E192641 APPROVED FOR USE IN DAMP LOCATIONS Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Hanging Bracket Installation. pg. 4 Fan Assembly. pgs. 5 - 6 Wiring. pg. 7 Canopy Assembly. pg. 8 Blade Assembly. pg. 8 Light Kit Assembly. pg. 9 Automated Learning Process.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2. 3. 4.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. b a c a. canopy. 1 piece b. hanging bracket. 1 piece e d c. downrod and hanging ball. 1 piece d. yoke cover. 1 piece f g e. canopy cover. 1 piece f.
12ft. - 20ft. (3.66m - 6.1m) 3. Installation Preparation. blade edge 30 10 feet inches (3.05m) (76cm) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 10 feet (3.05m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.
stop pin 5. Fan Assembly. set screw Remove hanging ball from downrod provided by loosening set screw on hanging ball. Lower hanging ball and remove stop pin and then slide hanging ball off of the downrod. [Refer to diagram 1.] Loosen yoke set screws and nuts at top of motor housing. Remove pin and clip from motor housing yoke. [Refer to diagram 2.
5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab.
6. Wiring. WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
7. Canopy Assembly. Locate 2 screws on underside of hanging bracket and remove screw closest to the open end of the hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. Place rounded part of slotted hole in canopy over loosened screw in hanging bracket and push up. Twist canopy to lock. Re-insert screw that was removed, and then tighten both screws securely.
. Light Kit Assembly. Remove 1 screw from motor plate on underside of motor housing and partially loosen the other 2 screws. Align slotted holes in fitter plate with loosened screws in motor plate, allowing molex connectors to come through center hole in fitter plate. Twist fitter plate to lock. Re-insert screw that was previously removed and securely tighten all 3 screws with a Phillips screwdriver. Remove 1 screw from underside of fitter plate and partially loosen the other 2 screws.
. Automated Learning Process./ Activating Code. CAUTION: The remote control transmitter can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. REMOTE CONTROL (back) Remove battery cover on back side of remote control transmitter. Install one 12-volt battery (included). battery Since this fan comes with an LED light kit, the dimmer switch (labeled ON and D) has been pre-set to the "ON" position (ON).
. Remote Control Operation. REMOTE CONTROL 2 III 1 IV V II I VI 3 4 Fan SPEED buttons--1: Fan OFF button--2: REVERSE function button--3: LIGHTING button--4: Use to control ceiling fan speeds 1-6 Use to turn the fan off Use to control fan direction Use to control down-light and up-light (if applicable) IMPORTANT: The Automated Learning Process takes approximately 5 minutes to complete.
. Smart WiFi Remote Control (Optional) To enjoy all the potential of your new device, you will need to download the Craftmade Smart app, available on the Google Play Store and Apple App Store, or use the QR code to download the app. Once you download the app, register new account and password. NOTE: Please keep this account information. You will use this account when you connect with your smart speaker. or When you log into the main page you will see the + on the right side of the top space.
Troubleshooting. Warranty. CRAFTMADEâ„¢ LIFETIME LIMITED WARRANTY: CRAFTMADE warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: CRAFTMADE will replace or repair any fan which has faulty performance due to a defect in material or workmanship. Contact Craftmade Customer Service at 1-800-486-4892 to arrange for return of fan. Return fan, shipping prepaid, to Craftmade.