COST WAY Cost way USER’S MANUAL 20"Industrial Fan Lamp ES10070US THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Please give us a chance to make it right and do better! Follow Cost way Contact our friendly customer service department for help first.
COST WAY Contact Us! Do NOT return this item. Contact our friendly customer service department for help first. E-mall US: ca ung@oostway com UK: cs subcontractor com Before You Start A\ Please read all instructions carefully. A\ Retain instructions for future reference. A Separate and count all parts and hardware. A Read through each step carefully and follow the proper order.
COST WAY To reduce the risk of electric shock, the electricity has been turned off at the circuit breaker or fuse box before begin. All wiring must be in accordance with the National Electrical Code NASI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician . The outlet box and support structure must be securely mounted and capable of reliably supporting only UL listed outlet boxes marked “Acceptable for Fan Support of less.
COST WAY WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation.Do not insert objects in the path of the blades. WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
COST WAY HARDWARE INCLUDED components table 2 NOTE:Hardware not shown to actual size. wire nut (not PACKAGE CONTENTS K Ramona control (Transmitter) Remote control (receiver) | 1 Slide-on mounting bracket ‘A «Canopy B 10" Downtrodden assemblywoman) ([Y «Hanging Pin assembly Cc Pin «Coupling cover cover : J Fan-motor assembly .E -an-motor assembly Pls check whether above accessories are completed or not?Yes, and install.
COST WAY Installation of the hanging bracket (suspension part) I Ny LLL Lu LLL Ly LLL For wooden ceiling, use wood screw to drill on the wooden beam or the “junction box” to fix the hanging bracket (selection is made according to actual requirements of the customers). SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX. 1)Use the Mounting Bracket (A) as a guide, mark the spots where the 4 Self Tapping Screws (B) will be drilled.
COST WAY Nuts Note: According to ths calling of different materials, use different screws to Th the hinging bracket. A | Don the hanging bracket on the was palling (aan than 12MM td prevent dangs; caused by Mona | Nonstaining of seawater. After tha hanging bracket is campsite, sincere that it can withstand has tension test of more Lien BIKO for acetyl. For concrete selling, use the percussion bit with materiel 8mm te drill holes according to the length of expansion screws.
COST WAY Install the hanging part of the ceiling fan. al ass 1. Thread the suspender through the suspended clock and coupling cover. 2. The insert the tail of the suspender from the lifting head of the motor. 3. After the lateral pin is threaded out from the suspended head position, insert R type pin. 4. Tighten the lifting head screws. 5. Hang the fan of the hanging pips into the hanger.
COST WAY Assembly — Attaching the Lights WARNING: Allow the shatter resistant bow! to cool completely before removing. CAUTION: Make sure the power is off before attaching or removing the shatter resistant bow. CAUTION: Do not over tighten the hex nonthreatening the hex nut may cause the shatter resistant bowl to break. ONLY USE BULBOUS 1.
COST WAY Assembly — Hanging the Fan(continued) a 6 ale al 6 WARNING:Each wire not supplied with this fan is designed to accept up to one 12-gauge house wire and two wires from the fan. If you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring, consult an electrician for the proper size wire nuts to use. IMPORTANT: Use the plastic wire connectors(BB} supplied with your fan.
COST WAY Assembly — Hanging the Fan(continued) n remote cont 1.Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight. 2.Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.
COST WAY E — rote 1 Less autocross) strew diver 1:Remove the mounting bracket from the canopy by loosening the two canopy screws located in the L shaped slots. 2:Remove and save the two canopy screws in the round holes. This will enable you to remove the mounting bracket.
COST WAY Care and Cleaning WARN! take sure IE off seining your O Because of the fan's natural movement, some connections may become loose.Check the support connectlons,brackets,and blade attachments twice a year. Make sure they are secure. It Is not necessary to remove the fan from the selling. O Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly cause an electric shack.
COST WAY Problem Solution The fan will not start. DO Heartache main and branch circuit fuses or bravuras. DO Hatchback line wire connections to the fan and switch wire connections In the switch housing. The fan will not start. 0 Ensure all motor housing screws are snug. 0 Ensure the screws that attach the fan bide bracket to the motor hub are tight, DO Ensues the wire nut connection are not rallying against each either or the interior ‘wall of the switch housing. 0 Allow a 24-hour breaking In” period.