KITCHEN FAUCET MODEL: COS-KF501SS
Thank You Thank you for your purchase. We know that you have many brands and products to choose from and we are honored to know that you have decided to take one of our products into your home and hope that you enjoy it. Our faucets are designed according to the strictest performance standards for the North American market. We follow the most advanced manufacturing philosophy. Each faucet leaves the factory after thorough quality inspection and testing.
Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Cosmo Appliances at 1-888-784-3108 Pre-drilled hole size requirement: 1-3/8” - 1-1/2” Max countertop thickness without deck plate: 1-3/8” Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean the sink of countertop to remove and debris, plumber's putty, and silicone.
TABLE OF CONTENTS PARTS DIAGRAM 04 PARTS INCLUDED 05 FAUCET DIMENSIONS 06 INSTALLATION PROCEDURES 08 OPERATING INSTRUCTIONS 11 TROUBLESHOOTING 12 3
4
5
6
The minimum distance between the faucet hole and the wall should be 3.5”. This is to ensure that the faucet lever can move freely allowing for full operation. If the distance between the faucet hole and the wall is less than 3.
Step 1 Hardware will be attached to the faucet during shipping. Remove hardware from the faucet to begin installation. Remove the Nut, Metal Ring, Silicone Ring and Plastic Holder. Set aside this hardware for the next installation step. Step 2 Insert faucet through the top hole of installation site. Attach Plastic Holder (A), Silicone Ring (B), Metal Ring (C) under the faucet. Use the Nut (D) provided to hold sink and hardware into place.
Step 3 Connect spray hose (B) to supply hose (A). Connect the hot and cold hoses (C). Hoses will be labeled on your actual product. A. Supply Hose B. Spray Hose C. Hose Step 4 C. Hose Proper installation of the hose counterweight will ensure that the sprayer retracts smoothly. On the sprayer hose measure 15" down from the body of the faucet and mark this point. Install the hose weight at this marked point. The sprayer should retract smoothly. Reposition the hose weight as necessary.
Step 5 Connect and tighten waterlines to hot and cold water supply (use Connect hot and (12)threads). to the angle with plumbers tape oncold the waterlines water supply Turnsto onand the tighten water supply snug,(DO thenNOT unscrew headON :&5 (8 YET), a wrench and checkuntil for leaks TURNspray FAUCET If no leaks are found turn the faucet on for 60 seconds to clear any debris from the water lines.
Usage How to Operate the Handle 25˚ Off On 1. Pull the lever to the right to turn on the water. Push to the left to turn off 2. Pull the lever forward (to wards you) to increase hot water flow and push the lever back (away from you) to increase the cold water flow.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 12 CAUSE ACTION Leakage under the handle. Locking nut has come loose . Remove the small chrome colored cap with red and blue (hot/ cold) dots. Remove the lever by loosening the set screw inside the hole with a hex wrench. Tighten the locking nut. Water will not shut off completely Cartridge needs to be replaced.
Codes/Standards Applicable: HELP LINE Our customer service hours are Monday – Friday, 10am – 5pm PST. Be sure to visit our website at www.cosmoappliances.com If you are a homeowner please contact a Cosmo Appliances Service Representative at: 1-888-784-3108 In requesting warranty service, please be ready to provide: 1. Proof of purchase. 2. A description of the problem. For full warranty details on this product please visit: http://www.cosmoappliances.
