Installation & Assembly

ManualsBrandsCorrigan Studio ManualsBathroom Vanity LightingFour-Light Indoor Wall Fixture

MOUNTING AND WIRING INSTRUCTIONS

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures

meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Beginning at sides and working at an angle, peel protective coating (if applicable) from face plate

(A) (see fig. 1).

3. Remove cups (B) from sockets (C) by simultaneously twisting and pulling cups (B) counter

clockwise off of sockets (C). If fixture is supplied with rings (R), unscrew counter clockwise off of

sockets (C).

4. Remove screws (D) and lock washers (E) (if applicable) from outer edges of face plate (A).

5. Separate decorative plate (F) (if applicable) and face plate (A) from back plate (G).

6. Push wires through back plate opening (H).

7. Identify color coding of fixture wires (see fig. 2).

8. Connect the black wire from the fixture with the black wire (live wire) from the outlet box by wire

connector (I), and wrap the wire connector (I) with electrical tape for a more secure connection.

9. Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box by

wire co

nector (I), and wrap the wire connector (I) with electrical tape for a more secure connection.

10. Partially thread green grounding screw (J) into side hole (K) on back plate (G) (see fig. 1).

11. Wrap grounding wire from fixture around green grounding screw stem (J) leaving enough excess

wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet

box by wire connector (I) (if applicable), then wrap the wire connector (I) with electrical tape for a

more secure connection.

12. Tighten green grounding screw (J). Do not over tighten.

13. Tuck wires inside outlet box (L).

FIXTURE ASSEMBLY INSTRUCTIONS

Warning: This fixture is for indoor use only.

NOTE: For maximum support, secure back plate (G) with wood screws (M) (or plastic anchors

(N)) if outer holes (P) meet sheetrock by following steps 1 and 2 below.

1. Position flat side of back plate (G) against wall at mounting location and mark outer holes (P) with

a pencil.

NOTE: Back plate (G) must be level for fixture to hang straight.

2. Drill a 1/8” hole at each mark then insert plastic anchors (N) by gently tapping with a hammer.

3. Place back plate (G) over outlet box (L) and secure using outlet box screws (Q) (if applicable), and

wood screws (M) (vertically or horizontally as desired, see fig. 1).

4. Position face plate (A) then decorative plate (F) (if applicable) over back plate (G) and sockets (C).

5. Secure by simultaneously twisting and pushing cups (B) clockwise over sockets (C) (for a tighter fit,

slightly bend tabs inside cups (B) outward).

NOTE: If fixture is supplied with threaded sockets (C), thread rings (R) onto sockets (C).

Replace screws (D) (if applicable) and lock washers (E) (if applicable) on outer edges of face plate (A).

7. Install lamp(s). Do not exceed recommended wattage.

8. Turn power back on at circuit box.

PLAQUE

ARRIERE (G)

PLAQUE

AVANT (A)

BAGUES (R)

(sil y a lieu)

CAPUCHONS (B)

TROUS

EXTERIEURS (P)

VIS DE MISE

A LA TERRE

(VERTE) (J)

*VIS DE LA BOITE

DE SORTIE DE

COURANT (Q)

DOUILLE (C)

VIS EN

BOIS (M)

VIS (D)

(sil y a lieu)

PLAQUE

ARRIERE (H)

RONDELLE DE

BLOCAGE (E)

(sil y a lieu)

PLAQUE

DECORATIVE (F)

(sil y a lieu)

CONNECTEURS

DE FIL (I)

ANCRAGE EN

PLASTIQUE (N)

TROU

LATERAL (K)

*BOITE DE SORTIE

DE COURANT (L)

BACK

PLATE (G)

FACE

PLATE (A)

RINGS (R)

(If applicable)

CUPS (B)

OUTER

HOLES (P)

GREEN

GROUNDING

SCREW (J)

*OUTLET BOX

SCREWS (Q)

SOCKETS (C)

WOOD

SCREWS (M)

SCREWS (D)

(If applicable)

BACK PLATE

OPENINGS (H)

LOCK WASHERS (E)

(If applicable)

DECORATIVE

PLATE (F)

(If applicable)

WIRE

CONNECTORS (I)

PLASTIC

ANCHOR (N)

SIDE

HOLE (K)

*OUTLET

BOX (L)

*NOT SUPPLIED

Line art shown may not exactly match the

fixture enclosed. However, the installation

instructions do apply to this fixture.

FIGURE 1.

WARNING

Turn off electricity to the mounting site before beginning installation.

Mounting instructions must be followed exactly as shown for the fixture to be safely supported.

CLEANING AND CARE

To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can

discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to

clean this fixture.

ORDERING PARTS

Keep this manual for future reference, and in case replacement parts are needed. Available parts can

be ordered from place of purchase. Use exact wording from diagrams when ordering parts.

FIGURE 2.

FIXTURE

WIRES:

Black

HOUSE

WIRES:

Black

(Hot)

HOUSE

WIRES:

White

(Neutral)

HOUSE

WIRES:

Bare

Copper

(Ground)

FIXTURE

WIRES:

Bare

Copper

(Ground)

FIXTURE

WIRES:

White

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com

, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.

*NON FOURNI

Il est possible que le dessin illustré ici ne

soit pas la reproduction exacte de l’appareil

d’éclairage contenu dans la boîte.

Les instructions d’installation demeurent

cependant valables.

FIGURE 1.

W-386

042820

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many

years of beauty and service. For questions and comments, please visit www.westinghouselighting.

com/contact-us.

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-

ing materials (see figure 1).

Owner’s Manual

Indoor Lighting Fixture

Installation Instructions

Fixture Warranty

This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period

of five years from purchase date. This warranty is in lieu of all other warranties expressed or implied.

This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration

of components, nor does it cover damages caused through abuse, improver installation, surges in

electric current, or acts of third parties.

This warranty does not cover the costs of removing and re-installing the lighting fixture.

If this product fails for any reason covered by this warranty, please contact us at www.westinghouse-

lighting.com/contact-us.

WARNING:

ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.

Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-

tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-

age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are

damaged, do not install fixture. Return to place of purchase.

For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provid-

ed on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985

have supply wires rated 60° C. Consult a qualified electrician before installing.

Guide d’utilisation

Instructions d’installation

Appareil d’éclairage pour utilisation intérieure

LES INSTRUCTIONS D’ASSEMBLAGE DE L’APPAREIL D’ÉCLAIRAGE POUR UTILISATION INTÉRIEURE

Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d’éclairage a été

conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à

nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.

NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces

y sont avant de mettre l’emballage au rebut (voir fig. 1).

GARANTIE LIMITÉE DE CINQ ANS

Ce luminaire Westinghouse est garanti pièces et main-d’oeuvre pour une période de Cinq ans à compter

de la date d’achat. Cette garantie remplace toute autre garantie, explicite ou implicite.

Cette garantie ne couvre pas les phénomènes naturels comme les dommages de la foudre, ni la corro-

sion ou la décoloration des composants, pas plus qu’elle ne couvre les dommages causés par les abus,

une installation inappropriée, les surtensions électriques ou les actes de tiers.

Cette garantie ne couvre pas les coûts de dépose et de pose du luminaire.

En cas de défaillance du produit, pour une raison quelconque, couverte par cette garantie, veuillez

nous contacter via www.westinghouselighting.com/contact-us.

MISE EN GARDE: L’ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.

Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez

pas l’installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de com-

mencer l’installation. Un câblage approprié est essentiel au bon fonctionnement de cet appareil

d’éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur ou un

plafond, n’endommagez pas les câbles électriques, les canalisations de gaz ou d’eau. Si l’un des

composants de raccordement ou de l’appareil d’éclairage est endommagé, n’installez pas cet

appareil d’éclairage. Retournez-le à l’endroit où vous l’avez acheté.

Convient uniquement aux appareils comportant un avertissement indiquant que l’appareil

d’éclairage est doté d’un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se

trouvent sur l’étiquette U.L. et sur l’emballage de l’appareil d’éclairage.)

Summary of content (2 pages)

PAGE 1
MOUNTING AND WIRING INSTRUCTIONS W-386 042820 Owner’s Manual Indoor Lighting Fixture Installation Instructions Fixture Warranty This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period of five years from purchase date. This warranty is in lieu of all other warranties expressed or implied.
PAGE 2
INSTRUCTIONS DE MONTAGE ET DE RACCORDEMENT INSTRUCCIONES DE MONTAJE Y CABLEADO NOTA : Underwriters Laboratories (UL) n’exige pas que tous les appareils d’éclairage comportent des fils de mise à la terre. Ces appareils satisfont cependant à toutes les spécifications UL. 1. Mettez l’interrupteur de la boîte de fusibles à « OFF » afin d’éviter le risque d’électrocution. 2. En commençant par les côtés et travaillant sous un angle, enlevez la couche protectrice (s’il y a lieu) de la plaque avant (A) (voir fig.