IMI CORNELIUS REMCOR INC g 500 REGENCY DRIVE g GLENDALE HEIGHTS, IL 60139--2268 Telephone (800) 551--4423 Facsimile (800) 519--4423 Operator’s Manual ICE/BEVERAGE DISPENSER Model: Enduro 200/250 IMPORTANT: TO THE INSTALLER. It is the responsibility of the Installer to ensure that the water supply to the dispensing equipment is provided with protection against backflow by an air gap as defined in ANSI/ASME A112.1.2-1979; or an approved vacuum breaker or other such method as proved effective by test.
TABLE OF CONTENTS Page MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 DAILY (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 WEEKLY (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MONTHLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE The following dispenser maintenance should be performed at the intervals indicated: DAILY (or as required) Remove foreign material from vending area drip tray to prevent drain blockage. WEEKLY (or as required) Clean vending area. Check for proper water drainage from the vending area drip tray. MONTHLY Clean and sanitize the hopper interior and beverage system if applicable (see CLEANING INSTRUCTIONS). START-UP & OPERATING INSTRUCTIONS Fill the hopper with ice.
DISPENSER 1. CLEANING EXTERIOR SURFACES Important: Perform the following daily. A. Remove the cup rest from drip tray. B. Wash the drip tray with soap solution. Rinse with clean water and allow solution to run down the drain. C. Wash cup rest with soap solution and rinse in clean water. Install the cup rest into the drip tray. D. Clean all exterior surfaces with soap solution and rinse in clean water. 2. COLD PLATE INSPECTION BEFORE CLEANING A. Remove splash panel. B.
BEVERAGE SYSTEM (IF APPLICABLE) CLEANING WARNING: Disconnect Power Before Cleaning! Do not use metal scrapers, sharp objects or abrasives on the ice storage hopper, top cover and the agitator disk, as damage may result. Do not use solvents or other cleaning agents, as they may attack the plastic material. Soap solution - Use a mixture of mild detergent and warm 100 degrees F potable water. Sanitizing solution - Use 1/2 ounce of household bleach in 1 gallon of potable water.
11. For post-mix valves, remove the nozzle and syrup diffuser and clean them in a mild soap solution. Rinse with clean water, then reinstall the nozzle and syrup diffuser on the valve. 12. For pre-mix valves, disconnect all product tubes from the tank of sanitizing solution and then open the valves to allow the pressure to be relieved. Remove the valves from the dispenser, disassemble and wash thoroughly in a mild soap solution. 13.
TROUBLESHOOTING IMPORTANT: Only qualified personnel should service internal components or electrical wiring. WARNING: If repairs are to be made to a product system, remove quick disconnects from the applicable product tank, then relieve the system pressure before proceeding. If repairs are to be made to the CO2 system, stop dispensing, shut off the CO2 supply, then relieve the system pressure before proceeding.
Trouble Probable Cause BEVERAGE NOT SWEET ENOUGH. BEVERAGES NOT COLD (UNITS WITH BUILT--IN COLD PLATE). A. Empty syrup tank. B. Faucet brix requires adjusting. A. Unit standing with no ice in hopper -- no ice in cold plate cabinet. NOTE: Contact your local syrup or beverage equipment distributor for additional information and troubleshooting of beverage system.
Part # Corrections/Update Document Unit Type/Model # Manual # ED200/250 92108 ICE/BEVERAGE DISPENSER Revision 2 8/11/06 Page Item Old Part 8 8 Desc. New Part Desc.
100 Graphics 92082 10 100 Graphics 92085 10 100 Graphics 92086 10 100 Graphics 92083 10 100 Graphics 92084 11 10 31763 629087448 11 10 32828 Agitator Timer 120V Agitator Timer 220-240V 12 629087451 70485 n/a n/a 91978 n/a n/a 91974 n/a n/a n/a n/a 08052 33666 n/a n/a n/a n/a 31001 629080104 n/a n/a n/a Dr Pepper Graphics ED250 7-Up Graphics ED200 7-Up Graphics ED250 RC Cola Graphics ED200 RC Cola Graphics ED250 Agitator Timer Kit 120V Agitator Timer Kit 220-24
90 57 5 33 80 87 67 64 67 1 93 56 27 68 26 39 63 77 79 92 94 4 C SEE DETAIL 74 85 32 88 52 50 77 77 67 74 24 76 6 66 46 76 62 44 49 72 30 65 25 48 10 88 73 34 72 82 34 18 22 91 74 54 60 100 14 53 55 95 17 16 16 18 12 84 15 88 72 23 88 86 59 72 8 13 101 DETAIL C SCALE0.093 83 FIGURE 1.
92108 Item No. Part No.
Item No. 43 Part No. Name Not Used 44 53199 45 Not Used Seal, Motor 46 51891 47 ***51908 48 71025 49 620500901 50 53168 51 Not Used 52 15132 Motor Mount 53 53001 Merchandiser, Gray (ED250) 53000 Merchandiser, Gray, (ED200) 52912 Merchandiser, Black, (ED250) 52911 Merchandiser, Black, (ED200) 15754 Merchandiser, S.S., (ED250) 15755 54 55 56 57 Gasket, Gate Plug Strap, Motor Ice Chute Ice Chute Cover Merchandiser, S.S., (ED200) 620011505 Merchandiser, S.S.
Item No. Part No. Name 77 70068 Washer, 3/8 I.D. x 11/16 O.D. x .070 Thk 78 Not Used 79 71061 Washer, 7/16 I.D. x 1 1/8 O.D. x .063 Thk 80 70320 Pop Rivet, 1/8 Dia. 81 70341 Spring, Motor Heater 82 71006 83 70478R Screw, No. 8-32 By 1 1/8-In. Long Clip, Push-on 84 70555 85 620022801 Brace, Reflector Screw, No. 8-32 By 2 5/8-In. Long 86 620701601 Sheet Metal Screw, No. 10 By 1/2-In. Long 87 70456 88 70959 Hex Nutsert, No.
17 15 14 6 18 16 1 12 5 4 2 3 9 13 8 11 10 FIGURE 2. ELECTRICAL BOX ASSEMBLY Item No. 1 2 Part No.
SOLENOID ASSEMBLY 4 9 11 5 14 3 6 5 12 10 15 13 8 7 1 2 FIGURE 3. SOLENOID ASSEMBLY Item No. Part No. 1 28173 Arm, Gate Lift 2 50754 Bearing, Gate Arm 3 32957 Solenoid, 120 Volts 33397 Solenoid, 220-240 Volts 4 28172 Plate, Solenoid Mounting 5 50752 Isolator 6 70015 Hex Nut, No. 10-32 7 51689 Locktite 8 70162 Screw, No. 8-32 By 1/4-In. Long 9 50705 Tie Cable 10 70165 Screw, No. 8-32 By 5/8-In.
DRAIN TO COLD PLATE DRAIN ELBOW 1 3 4 1 TO COLD PLATE DRAIN ELBOW 1 1 2 1 3 FIGURE 4. DRAIN FOR Z STYLE UNITS WITH COLD PLATES Item No. Part No.
WARRANTY IMI Cornelius Inc. warrants that all equipment and parts are free from defects in material and workmanship under normal use and service. For a copy of the warranty applicable to your Cornelius, Remcor or Wilshire product, in your country, please write, fax or telephone the IMI Cornelius office nearest you. Please provide the equipment model number, serial number and the date of purchase. IMI Cornelius Offices AUSTRALIA D P.O.
THIS PAGE LEFT BLANK INTENTIONALLY 15 92108
IMI CORNELIUS INC.