Use and Care Manual

©2022 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. < 5 g/L • REV. 04/21
PRODUCT USES
For application to hard, non-porous interior walls, ceilings, doors
and trim in residential, commercial and institutional settings.
Ideal for use in homes, offices, clinics, nursing homes, athletic
facilities, schools, community centers, daycare centers, assisted
living communities, hotels and resorts. Also suitable for non-
critical areas of hospitals, such as examination rooms, waiting
rooms, hallways and walkways. See SURFACE CARE AND
MAINTENANCE for proper care and cleaning information.
DO NOT USE ON FLOORS OR ON EXTERIOR SURFACES.
DIRECTIONS FOR USE
It is a violation of federal law to use this product in a manner
inconsistent with its labeling.
SURFACE PREPARATION*
• All surfaces should be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling paint,
rust, and all other foreign substances. Scuff sand glossy
surfaces and repair imperfections. Allow new concrete, plaster
and masonry to cure for 30 days before painting.
• Although this product is a paint & primer (self-priming — first
coat is the primer and the second coat is the finish) over most
properly prepared surfaces, certain substrate and exposure
conditions, as well as project requirements, may necessitate the
use of substrate-specific or solution-driven primers.
*ATTENTION If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and a
wet mop. Before you start, find out how to protect yourself and
your family by contacting the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.
APPLICATION
• For best results, apply when air, material and surface
temperatures are between 50°F and 90°F.
• Stir paint occasionally. Intermix containers of same product to
ensure color and sheen uniformity.
• Do not thin. Product is formulated at package consistency.
• Apply two coats by brush (nylon/polyester), roller (3/8" – 1/2"
nap) or airless sprayer (.015" – .019" spray tip) at a coverage
of 250 – 400 sq ft per gallon. Coverage depends on application
method and substrate porosity. Certain colors may require
additional coats for complete hide.
• Dries to touch in 1 hour; recoat after 2 hours @ 77°F and 50%
RH. Drying and recoat times are dependent on temperature,
humidity and film thickness.
• Clean all tools and equipment with soap and water.
To avoid breathing vapors and spray mist, open windows and
doors or use other means to ensure fresh air entry during
application and drying. If you experience eye watering,
headache or dizziness, increase fresh air. If properly used,
a respirator (NIOSH approved for organic vapor with P series
particulate pre-filter) may offer additional protection; obtain
professional advice before using. A dust mask does not provide
protection against vapors.
STORAGE AND DISPOSAL
Do not contaminate water, food, or feed by storage and
disposal. PESTICIDE STORAGE: Store away from food and pet
food. Open dumping is prohibited. Keep container closed when
not in use. Do not transfer contents to other containers. Protect
pesticide containers from extreme heat and cold.
PESTICIDE DISPOSAL and CONTAINER HANDLING: Nonrefillable
container. Do not reuse or refill this container. If empty: Place
in trash or offer for recycling if available. If partly filled: Call
your local solid waste agency for disposal instructions. Never
place unused product down any indoor or outdoor drain. Waste
resulting from the use of this product may be disposed of on
site or at an approved waste disposal facility.
SURFACE CARE AND MAINTENANCE
Periodic cleaning to remove dirt and stains is necessary for
good sanitization and to assure the effective virucidal and
antibacterial performance of the surface. Cleaning does not
reduce the virucidal and antibacterial performance of the
painted surface. To ensure continuous protection, repaint
surface if film becomes damaged (peeled, cracked, etc.) or if
paint becomes covered with oils, grease, wax, other paints and
other foreign substances; or within 6 years.
Proper Surface Care and Use: The use of an antimicrobial
treated surface is a supplement to and not a substitute for
standard infection control practices; user must continue to
follow all current infection control practices, including those
practices related to cleaning and disinfection of environmental
• Virucidal & Antibacterial Paint
• Durable, Long-Lasting Finish
• Mildew Resistant Paint Finish
• Paint & Primer
◊
• Excellent Hide
• Low Odor
• 100% Acrylic
• Limited Warranty*
TINTABLE WHITE: READY TO USE OR ADD TINTING COLORANTS.
DEEP BASE: DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS.
◊
A primer coat may be needed on some surfaces. See back label for details.
BEHR
®
COPPER FORCE
™
Interior Semi-Gloss Enamel
No. 3190 Tintable White
No. 3193 Deep Base
EPA Registration No. 32273-10