Battery Powered Portable Multifunctional Amplifier MR 2
ENGLISH MR 2 Batter y Powered Por table Multifunctional Amplifier Thank you for selecting the MR-2 Battery Powered Portable Multifunctional Amplifier.
QUICK SET-UP GUIDE 1. Connect the line cord to the appropriately rated receptacle. 2. Be certain that all levels are down or set to the fully counter-clockwise position and set all the EQs flat 3. Set the master level to the 12:00 position 4. Connect output of your music instrument to the input of the M2/M3 5. Set the main/monitor switch to the monitor position 6. Turn on power to the M2/M3 7. Adjust the channel level for proper volume 8. Adjust the channel EQ as needed.
Up/center/down key control(13) Effect control mode and Mp3 Play mode use three key operate Long Push ENTER key to switch between this two mode In effect control mode, use UP,DOWN key to select one of the 99 popular effects. Long push UP DOWN key can change the WET/DRY ratio at this state. In MP3 mode, use UP,DOWN key to select songs store in the USB disk. Long push UP DOWN key can change the volume of songs at this state. System can detect a U-DSIK plug-in automatically. Effects list Effect No.
CH3/Monitor Input Jack (5) Use this 1/4" jack to connect to the output of any line-level device. Channel 2 High-Impedance Input (6) This 1/4" jacks accepts high-impedance microphones or line-level sources equipped. Channel 2 Low-Impedance Input (7) For use with low-impedance microphones or other line-level sources equipped with a male XLR connector. Channel 1 Inputs (8‚ & 9) This 1/4" jack accepts high-impedance microphones or line-level sources equipped.
Connecting an additional unit to increase the output (Stereo Link) By connecting two MR2 units you can create a stereo PA system with greater output power. This function is called “Stereo Link.” You can connect Stereo Link in either of the following two ways. If using the input jacks of only one of the units Use one cable with a 1/4” phone plug and RCR for another side.
Output Level: 18 dBV POWER AMPLIFIER SECTION Rated Power and Load: 80Watts RMS/4 Ohms or 60WRMS/8 Ohms (1 kHz, 1% THD @ 120 VAC line) Frequency Response: +0, -1dB, 20 Hz–20 kHz @ 60 Watts RMS/8 Ohms Total Harmonic Distortion: Less than 0.01% @ 1 kHz/8 Ohms Typically less than 0.
中 文 MR-2便携式可充电多功能音响系统使用说明 感谢你选择使用我们的MR2便携式可充电多功能音响系统,我们的工程师和艺术家经过多年对各 种键盘乐器;电子鼓乐器;原声电吉他;人声话筒发声的测试和研究,最后终于可以将其发声诸 多特性和优点融入到M3/M2便携式多功能音响系统之中,所以我们可以保证我们最新的M3/M2 便携式多功能音响系统能够发出最优美的声音为;原声电吉他, 电子鼓乐器;各种键盘乐器;人 声话筒—无论是低音或是高音,我们的MR2便携式可充电多功能音响系统都能够对他们进行完美 的处理,并还原给你最美妙的声音. 在开始使用你的功放之前,请确定你的电源输出电压是与你的功放完全匹配的,你可以在产品的背 面看到适合你功放使用的输出电压,另外在功放的背面,你还可以发现一个额外的音箱接口,如有需 要,你可以在此接口接入多一只合适的音箱以求获取更大的扩声效果. 在使用之前请仔细的阅读这本产品说明书以确保你个人和产品的安全.
Hi EQ (3) 主动式高音音色控制旋钮(shelving type: +/-15dB) 用于调整高频频响范围 ( channels 1 & 2.
Headphone Jack (4) 立体声耳机插孔 CH3/Monitor Input Jack (5) 通道3监听信号输入插孔,可接入各类高阻抗的话筒信号或音频信号 Channel 2 High Input (6) ;通道2信号输入插孔,可接入各类高阻抗的话筒信号或音频信号 Channel 2 Low-Impedance Input (7) 通道2(M2)低阻抗XLR输入插孔,可接入各类低阻抗的话筒信号或音频信号 Channel 1 Inputs (8‚ & 9) 通道1输入插孔可接入各类高阻抗的话筒信号或音频信号 后背控板 Power inlet socket 电源插孔 这是一个标准的IEC电源插孔,一根与之配对的电源线是可以发现的在我们的纸箱盒里,在你连接电 源之前,你需要先将此电源线连接到功放上.