www.contixo.
1. Pre-Flight Preparation Before you take off, make sure that: 1. The drone and the remote controller are completely charged. 2. The propellers are installed correctly. 3. The motors work normally after unlocking. Drone Battery Charging How to charge the drone battery: 1. Connect the battery to the balanced charger as show below. 2. A full charge takes about 5 hours. During the charging process, the green light will be flashing slowly and a solid red light will be on.
2. Download the Mobile App The Contixo F20 App is available for download on both Android and iOS devices. Search "Contixo F20" in the Google Play Store or App Store and install the App. How to link the Contixo F20 App to the drone’s camera: First, turn on your drone. Then enter into your phone settings. Turn on Wi-Fi, find “Drone_XXXX” on the list, and connect your device to that WiFi signal. Next, exit settings and tap open the "Contixo F20" App on your smartphone; click ‘START’ to enter the APP interface.
3. Product Assembly Remote Battery Installation Using the supplied screwdriver, unscrew counterclockwise to open the battery compartment cover and install four (4) AA batteries into the battery compartment according to the given polarity. Screw clockwise to close the battery compartment.
4. Product Assembly (continued) Smartphone Clip Holder Locate the F20 smartphone clip and attach it to the antenna of your remote. Simply slide the phone holder into place until you hear a “click” indicating the clip is secured. The smartphone device clip is essential for FPV (First Person Viewing) while flying your device. Please note that the Wi-Fi connectivity from the drone to your smartphone can be affected by multiple factors.
. Link the Remote Controller with the Drone Remote Control Signal Connection The drone must first be turned off for this to work. All you need to do is “simultaneously” press the red button on top of the remote and turn on the power of the remote controller. The remote will send out 2 beeping sounds and the indicator light will keep flashing (indicating that the remote controller is now ready to connect to the drone). The signal connection setup will only need to be completed once.
. Calibrate the Drone’s Compass Step 1) Horizontal Calibration When the drone's front and rear lights flash yellow alternatively, hold the drone horizontal and rotate it 360 degrees (counterclockwise) along the central axis for about 3 circles. The drone’s front and rear lights will change from flashing yellow to flashing green alternatively when you complete this step.
. Enable GPS (Global Positioning System) GPS mode enables precise positioning and prevents drone loss. Simply move the GPS switch to the “ON” position before operating the drone to use all of the GPS features (such as Auto Return/Return to Home and Low Battery Return To Home). ATTENTION: After the compass is calibrated, you must wait approximately 1-2 minutes until you achieve a GPS signal of at least 7. For best results, please operate the drone outdoors and in good weather condition.
. How to Start or Stop the Drone Unlocking the Drone Short-press the red button. The motors will begin to rotate and the drone will be ready for liftoff. Locking the Drone Pull down the throttle stick to the bottom position until the propellers stop. When the propellers stop, it means the drone is locked.
. One Key Takeoff and Landing One Key Takeoff After the drone is unlocked, short-press the take off button (as indicated below), the drone will automatically takeoff and hover at a altitude of 5 ft. One Key Landing When the drone is flying, short-press the landing button (indicated as below), the drone will automatically land on the ground. You can control the drone as it descends if you need to avoid obstacles. When the drone lands and the motors stop the drone will be locked.
. Return To Home (RTH) The Return-to-Home(RTH) procedure brings the drone back to the last recorded Home Point. There are 3 types of RTH procedures: smart RTH, failsafe RTH and low battery RTH. GPS Home Point Description The Home Point is the location from where the drone takes off. A strong signal of at least 7 must be present prior to take off in order for the drone to remember the home point.
. Congratulations, you are now ready to fly! Please be careful and have fun. Please refer to the user manual for flight controls and additional information. Always use common sense when flying a drone. Thank you for choosing Contixo Products. support@contixo.
