® MONTEGO BAY CELUXE TM 52MBD5 52" HUGGER FAN TM Owners Manual and Installation Instructions A Continuing Commitment to Excellence
READ AND SAVE THESE INSTRUCTIONS Before beginning installation of your new Concord ® ceiling fan, read and follow these safety precautions. If you are not familiar with national and local electrical codes and basic electrical wiring procedures, we recommend that you have a qualified electrician install your new ceiling fan. Before you begin, TURN OFF THE ELECTRICITY. Determine which circuit your new fan will be using and remove the fuse or turn off the circuit breaker at the main electrical panel.
This ceiling fan was not designed for installation in any location where it might be exposed to moisture or high humidity. Installation in this type of location could be UNSAFE, will most likely damage the fan and its finish... and will VOID YOUR WARRANTY. Every effort has been made to provide you with proper instructions for the safe installation of this ceiling fan. You could however, encounter situations or problems not covered in this manual.
Have you TURNED OFF the Electricity? Step 1 Attach the mounting plate In order to operate properly, this type of ceiling fan must be installed on a flat and level ceiling. If you have a sloped ceiling, you should return the fan and purchase one with a sloped or vaulted ceiling mounting system. Fig. 1 Junction Box Select the ceiling mounting plate (see figure 1). Pull the electric wires in the junction box down through the center hole in the mounting plate (see figure 2).
Mounting Plate Step 2 Hanging the Motor Hang motor assembly on motor assembly hook (see figure 4). Electrical Connections To operate the ceiling fan with the pull chain(s) and switches mounted on the fan, follow the instructions below. If you require or would like to use a different method of controlling your fan, refer to the Optional Electrical Wiring Procedures (page 8) later in this manual.
Mounting Plate Step 3 Hanging the Fan Body Carefully slide Motor Housing over Motor Assembly (see figure 6) and secure with four (4) Motor Housing screws. Motor Assembly Motor Housing Screw Motor Housing Step 4 Fan Blade and Blade Arm Assembly Most CONCORD fans are supplied with a reversible blade finish. Choose the blade finish that you prefer and attach as follow: Attach each fan blade to a blade arm with three 3/16” x 7.5 mm blade screws and three 3/16” fiber washers (see figure 7).
Step 6 Light Fixture Installation Back off (loosen) the three screws on the electrical housing cover (see figure 9). Connect White wire to White wire, and Black wire to Blue wire using quick connectors. Press together firmly. Three Speed Switch (pull chain) Screws Place light fixture onto fan, line up the 2 holes and rotate light fixture; Insert the screws and tighten. Wire Nuts Light Fixture Fig.
Optional Wiring Diagrams Fan controlled with wall switch and Light controlled at fan Figure 11 illustrates the wiring used to control the fan with a wall switch plus an optional light fixture controlled at the fixture. Figure 12 illustrates the wiring used to control fan with the pull chain on the electrical switch housing plus an optional light fixture with a wall switch. Figure 13 illustrates the wiring used to control the fan and optional light fixture with separate wall switches.
Your new CONCORD ceiling fan is now ready for use. Reset your circuit breaker and restore power to the circuit. See the Operation Instructions below to review the function of each control on your fan. Operation Instructions The three speed pull chain located on the switch housing (see figure 9) controls the speed of your fan. When the fan is OFF, pull the chain once for HIGH speed, twice for MEDIUM speed, three times for LOW speed and fourth time to turn it off again.
Maintenance Your fan requires very little maintenance. Cleaning of the housing should be done with a damp soft cloth (NO CLEANING AGENTS). On the blades, use a duster or dry cloth because any moisture could cause the blades to warp.
Mounting Plate Motor Assembly Hook Mounting Screws Hole for Motor Assembly Hook Motor Assembly Switch Housing Mounting Washer and Nut Reverse Switch Three Speed Switch (pull chain) Motor Housing Screw Motor Housing Blade Screws and Lock Washers Light Fixture Blade Blade Arm Blade Arm Screws Light Switch (pull chain) Switch Housing Screw Thumb Screws Glass Shades Bulbs 11
® Concord Fans and Lighting Concord Fans and Lighting.