02'(/ 57$ % $66(0%/< ,16758&7,216 7KDQN \RX IRU SXUFKDVLQJ RXU SURGXFWV 6FDQ 45 &RGH WR YLHZ IXOO DVVHPEO\ YLGHR
3 57$ % 3OHDVH UHDG FDUHIXOO\ WKH DVVHPEO\ LQVWUXFWLRQV EHIRUH WKH LQVWDOODWLRQ 'R QRW GLVFDUG WKLV PDQXDO RU DQ\ RI WKH SDFNDJLQJ PDWHULDO XQWLO WKH XQLW KDV EHHQ FRPSOHWHO\ DVVHPEOHG 6FDQ 45 &RGH WR YLHZ IXOO DVVHPEO\ DQG VWHS YLGHR 3
57$ % 3 3 MAIN PARTS LIST #1 Left panel x1 #2 Right panel x1 #3 &DVWHUs x4 #4 %DFN panel x1 #5 )URQW panel x1 # 0LG panel x1 # %RWWRP SDQHO x1 # 7RS SDQHO x1 # /DWHUDO VWUXFWXUH x # 7RS VWUXFWXUH x # 11A: 3ODVWLF FRYHU x # 0DLQ panel x1 11B: 6FUHZ NQRE # 3URWHFWRU WXEH x1 SCREWS LIST:
57$ % 3 3 3 3 MAIN PARTS LAYOUT ( FOR REFERENCE ): 13 12 10 11 11 8 6 9 2 1 5 7 ֊ This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware. Cam Bolt 1. Screw the bolt into the corresponding panel. Cam Lock 2.
3 57$ % 3 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. ❶ Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions. ❼ To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly. ❷ Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product.
57$ % 3 5 3 5 ASSEMBLY STEPS First screw bolts ( ' into panel ( 1 ), then place down the Back panel ( 4 ), the Front panel ( 5 ) and the 0LG 3DQHO and assemble them by turning the cam locks on those panels as shown and as explained in page 3.
57$ % 3 6 STEP 8VH VFUHZV $ WR DVVHPEOH WKH FDVWHUs WR WKH Eottom surface of the bottom panel ( 7 ). Please note that the LOCKING casters go at the FRONT.
57$ % 3 7 First screw the %ROWV ' WR WKH 7RS 3DQHO ), then place it down and assemble it to the structure by turning the cam locks on panel ( 1 ), ( 2 ) and ( 4) as shown and as explained in page 3. STEP Item: ' 6x mm 3 7 x 8 4 6FDQ 45 &RGH WR YLHZ WKLV VWHS 2 1 8VH VFUHZV & WR IL[ WKH /DWHUDO VWUXFWXUH WR OHIW DQG ULJKW SDQHOV DQG WR WKH ERWWRP SDQHO .
57$ % 3 8 STEP 7 3 8 3ODFH WKH 3ODVWLF &RYHUs $ over the /DWHUDO 6WUXFWXUH 7XEHV with their holes facing towards the outside 11A 6FDQ 45 &RGH WR YLHZ WKLV VWHS STEP Hole facing to the outside 9 ,QVHUW WKH 7RS 6WUXFWXUH 7XEHV through WKH 3ODVWLF &RYHUs $ , WKHQ screw in the WKH .QREs % LQWR WKH 3ODVWLF &RYHU $ . Make sure to raise and set the tubes a little bit higher and at the same level for easy accessibility during the next step.
57$ % 3 9 8VH 6FUHZV & WR DVVHPEOH WKH 0DLQ SDQHO to WKH 7RS VWUXFWXUHs from underneath. STEP Item: & 3 9 6x 5mm 12 x4 10 10 6FDQ 45 &RGH WR YLHZ WKLV VWHS 8VH 6FUHZV ( % ) WR IL[ WKH 3URWHFWRU 7XEH WR WKH 0DLQ 3DQHO from underneath. STEP 1 Screws: % x mm STEP x 13 12 6FDQ 45 &RGH WR YLHZ WKLV VWHS 6FDQ 45 &RGH WR YLHZ WKLV VWHS 7LJKWHQ DOO VFUHZV ZHOO.
57$ % 3 0 FINAL 67(3 ALL '21( *LYH \RXUVHOI D QLFH SDW RQ WKH EDFN
57$ % 3 1 3 1 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING WARNINGS FOR CARE AND MAINTENANCE: t /',d >/D/d^ ϮϬ >ďƐ͘ ϮϬ >ďƐ͘ ϭϱ >ďƐ͘ ϮϬ >ďƐ͘ Do not exceed the indicated weight limits. Do not expose the surfaces to direct sunlight or to extreme environmental conditions. Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel. Do not use solvents or abrasive materials to clean the unit.
