TORNADO PRESSURE WASHER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.
Technical Specifications Tornado P1 Mini Bowser Tornado P2 Engine Pump Pressure Flow HP Nozzle Gearbox Unloader Pump Oil Gearbox Oil Noise Honda GX200 6.5HP @ 3600rpm AR XT13‐15 2200psi / 150 bar 13 lpm / 2.9gpm 15045 2:1 Reduction Minimatic 4B 10W/40 EP90 Honda GX340 11HP @ 3600rpm AR RK15‐20H 2900psi / 200 bar 15 lpm / 3.
FAULT FINDER FAULT CAUSE REMEDY Boiler will not work Blown Fuse Check power to electrical enclosure and 3.15 amp control fuses Sudden pressure loss No Water No Chemical Burst Disc Blown Check water supply Check Chemical drum, close valve Replace Disc. Water turns to steam during normal Use. Partially blocked H.P.
MINIMUM SERVICE SCHEDULES DAILY CHECK THE FOLLOWING a. b. c. d. Oil level ‐ top up as required. Fuel tank ‐ top up as required. All hose unions for leaks‐ replace O rings if leaking. Hose condition ‐ cuts etc. EVERY 500 HOURS OR SIX MONTHS (WHICHEVER COMES FIRST) a. b. c. d. e. Drain and replace pump oil. Drain and refill fuel tank. Replace fuel filter. Clean water filter. Replace high pressure nozzle. EVERY 1000 HOURS OR 12 MONTHS (WHICHEVER COMES FIRST) a. b. c. d. Complete 500 hour service.
OPERATING INSTRUCTIONS SAFETY I II Water at high pressure is dangerous and can cause serious injury. This machine is to be used with great caution. Petrol is extremely flammable and explosive under certain conditions. EXHAUST FUMES CONTAIN CARBON MONOXIDE – Inhalation of such fumes can KILL. III Diesel is flammable and harmful if swallowed. A Always refuel in an area which is adequately ventilated. B DO NOT smoke when refueling. C Avoid overfilling.
L Always ensure that there is a suitable type fire extinguisher available and is within access. M DO NOT leave an engine running unattended, ALWAYS STOP it before leaving the area. N NEVER point the high pressure spray jet at any person, animal, glass or other Material which may shatter. O PREVENT any over spray from injuring other people or damaging property.
PREPARATION Water Supply: A B Ensure there is an adequate water supply either from the mains or a reservoir. Attach water supply hoses to suitable tap or immerse the suction hose with approved suc‐ tion filter into the reservoir. NOTE: ONLY CLEAN WATER SHOULD BE USED. THE PUMP MAY BE DAMAGED IF DIRTY OR CONTAMINATED WATER IS ALLOWED TO PASS THROUGH THE PUMP. Hoses: Low pressure inlet. For models up to 13 litres per minute use ½ “ bore suction hose or feed pipe.
D Adjust pressure regulator as required to obtain working pressure if required. E NOTE;:The high pressure water will cause the gun to “kick”. Make sure you have a firm grip of gun and lance. F On completion of operation stop the engine. g. Operate lance trigger h. Turn “ OFF” water supply i. Release residual pressure in gun and lance by operating trigger. When using Cleaning Agents: A. Set machine up as for water. B. Connect detergent hose to machine and place filter end into detergent. C.
Jockey Wheel Engine Yanmar L100 Diesel Honda GX340 Petrol Pump ARRK 15:20 Unloader Valve ARGM3B250 Chemical Pick Up Pipe Key Start (Diesel Only) Basket Filter (Inside Lid) 30 Mtr Hose HH00100MVG Hose Reel MTM20027 Tornado Bowser ‐ General Arrangement
Tornado Mini‐Bowser ‐ General Arrangement Basket Filter (Inside Lid) Hose reel MTM2002 Tank Lid 15 Mtr Hose HH00050MVG Pump to Hose Reel HH00188 Braked Caster Wheel Wheel500 Wheel Wheel400 Engine P1 Honda GX120 P2 Honda GX200 Chemical Pick‐Up Pipe Pump Unloader Valve Pressure Guage DEM20620 Fast Drain
WARRANTY This warranty covers the cost of all replacement parts and labour charges incurred, but does not cover the cost of transport or carriage. It is the owners responsibility to return the machine to a service depot or pay the travelling expenses of a engineer to attend. Demon Internationals decision in warranty matters is final and binding.
Warranty Procedure End Users If your machine develops a problem: 1. Phone Demon for advice with the model and serial number to hand. 2. Describe fully the problem as best you can. 3. If the problem cannot be resolved over the phone then the machine can be booked in for repair and if the faults are covered by the warranty the repair will be carried out free of charge. 4. If you cannot bring the machine in for repair then we will despatch an engineer.
Storm N/A Storm 1&2 N/A N/A N/A Description Cold Water Lance 04 Yellow Cold Water Lance 045 Blue Cold Water Lance 05 Red Hot Water Lance 045 Blue Hot Water Lance 05 Red Part Number DEM10031Y DEM10031B DEM10031R DEM10032B DEM10032R N/A N/A WM4 WM1 N/A Wall Mounted N/A N/A P4 & D1 P2 N/A Hurricane Typhoon 1&2 N/A Tempest 1, 3 & 4 (13.17 pump) Tempest 4 (15.
Adjustable Nozzle QR Lamce P2 N26001/15045 N26001/1505 MTM90040 DEM10031B DEM10031Y DEM10031R DEM10030 MTM70012 1 1 2 3 3 3 4 5 MVG Coupling QR Trigger QR Lance P4 & D1ES QR Lance P1 Nozzle P4 & D1ES Nozzle P2 Nozzle P1 N26001/1504 1 Description Part No Pos COLD WATER LANCES 1 1 1 1 1 1 1 1 1 Qty
3 1 Nut High Pressure Hose Hose Joiner 2. 3. 4. 2 HH00050MVG HH00100MVG 15 Metre 30 Metre MV00500 HH00030MVG MV00490 (items 1 & 2) Alternative Hose Lengths Hose Insert 1.
XT 1450 Pos Code No Description Qty Pos Code No Description Qty 1 AR1322730 Screw 6 40 AR1320020 Pump Head 1 2 AR620301 Plug 1 41 AR180101 O Ring 1 7 AR1260162 Plug 6 42 AR820361 Plug 1 8 AR960160 O Ring 6 43 AR1260200 Crankshaft 1 9 AR1269050 Complete Valve 6 43 AR1320260 Crankshaft 1 10 AR880830 O Ring 6 44 AR1380520 Key 1 11 AR1320340 Support Ring 3 45 AR1320370 Bearing 1 12 AR1260220 Gasket 3 46 AR1260750 Seal 1 13 AR1320351 Pis
RK MODEL: 15.20H Pos Part No Description Qty Pos Part No Description Qty 1 AR960160 O Ring 6 36 AR1343510 Screw 6 2 AR960090 Plug 6 40 AR1380120 0.10mm shim 1÷3 2 AR1380740 Plug 6 40 AR1380130 0.20mm shim 1÷3 3 AR1389051 Complete Valve 6 40 AR1380530 0.25mm shim 1÷3 4 AR880830 O Ring 6 40 AR1382810 0.
GYMATIC 3/A Pos Part Number Description 1 AR1560580 Knob plug 2 AR180030 Screw 3 AR1660210 Nut 4 AR1560400 Handle 5 AR1080070 Pin 6 AR1560420 Adjusting screw 7 AR1560410 Spring guide 8 AR1560440 Plate 9 AR1560350 Spring 10 AR1080610 Spring plate 11 AR1080660 Pin 12 AR1080540 Upper piston 16 AR1560100 Jet 17 AR1560140 Spring 19 AR880581 Plug 20 AR820510 O ring 21 AR1560020 Valve housing 25 AR1560320 Lower piston 27 AR1080831 By pass adjuster 29 AR1
