Installation Guide

ManualsBrandsClearView GLASS RAILINGS ManualsDeck Railing SystemsClearView Glass Railings 60 in. x 39.37 in. Tempered Laminated Hercules Glass Panel with Spigots

ClearViewClearView

GLASS RAILINGS

ClearViewClearView

GLASS RAILINGS

ClearViewClearView

GLASS RAILINGS

Wood Deck Installation

The hold down force for each spigot is 2,500 lbs. We suggest using 3/8” diameter x 3.5” ASTM A307 Grade A

structural bolts as they have sufﬁcient capacity to resist this force. Use with ﬂat washer to fasten spigots to wood

deck. ASTM A307 Grade A structural bolts and washer should be cadmium plated or stainless steel so they do not rust.

Lag bolts must be installed into rim joists or lam beam or properly blocked sub structure. If lag bolts are attached to

deck planks only failure will occur as a result of improper installation. Improper installation

and failure may result in injuries or death. Do it once and do it right!

INSTALLATION WITH

TWO OR THREE SPIGOTS

2 SPIGOT INSTALLATION

3 SPIGOT INSTALLATION

Will Withstand Hurricane Force Winds

Will Withstand Wind Gusts up to 115 MPH

Installation of Spigots Using Wood Planks

Installation of CVGR Spigots to wood planks are ﬁne as long as you use three

2” x10”s. You must tie the three plies of wood together with (4) #8 4” wood

screws*, located 3” from spigot screws.

More installation information including additional fastener product recommendation

listed on next page. Product Speciﬁcations included as well.

*Or use four RSS Rugged Structural Screws (5/16x4) by GRK Fasteners shown at top of next page.

Summary of content (13 pages)

PAGE 1
C G ClearView GLASS RAILINGS INSTALLATION WITH TWO OR THREE SPIGOTS 2 SPIGOT INSTALLATION Will Withstand Wind Gusts up to 115 MPH 3 SPIGOT INSTALLATION Will Withstand Hurricane Force Winds Wood Deck Installation The hold down force for each spigot is 2,500 lbs. We suggest using 3/8” diameter x 3.5” ASTM A307 Grade A structural bolts as they have sufficient capacity to resist this force. Use with flat washer to fasten spigots to wood deck.
PAGE 2
- r Fastener Recommendation We recommend RSS Rugged Structural Screws by GRK Fasteners (product image shown). Based on their rated loads the screw has an allowable steel strength in tension of 1,415lb. Utilizing a 200lb point load at the top of a 42” glass panel with 2 spigots, the tensile load per fastener (1 per spigot) is 1,333lb. The GRK RSS 5/16x4 fasteners are strong enough to resist the applied load.
PAGE 3
CLEARVIEW GLASS RAILINGS • 737 Quentin Avenue South • Lakeland, MN 55043 • ClearViewGlassRailings.com GENERAL NOTES: 1. THIS GUARDRAIL SYSTEM IS IN COMPLIANCE WITH THE 2014 AND 2017 INTERNATIONAL BUILDING CODE (IBC) SECTION 1607.8. IT IS ALSO IN ACCORDANCE WITH 2015 IBC SECTION 2407 THAT REQUIRES ALL-GLASS HANDRAILS AND GUARDS BE "LAMINATED GLASS CONSTRUCTED OF FULLY TEMPERED OR HEAT-TREATED GLASS". 2.
PAGE 4
ClearView Glass Railings Attachment to Concrete CVGRailings spigot baseplate is about 4” diameter. With this, we have come up with the following: We are specifying an adhesive anchor system by HILTI: 3/8” diameter HIT-Z anchor, with their HY200-R adhesive. Effective embedment = 2 3/8”. HILTI has many anchors and it is important that they use this exact anchor. We have attached the HILTI report that describes this design.
PAGE 5
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: | Concrete - Apr 5, 2021 Page: Specifier: E-Mail: Date: 1 4/5/2021 Specifier's comments: 1 Input data Anchor type and diameter: HIT-HY 200 + HIT-Z 3/8 Item number: 2018440 HIT-Z 3/8" x 4 3/8" (element) / 2022793 HIT-HY 200-R (adhesive) Effective embedment depth: hef,opti = 2.375 in. (hef,limit = 4.500 in.
PAGE 6
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: Page: Specifier: E-Mail: Date: | Concrete - Apr 5, 2021 2 4/5/2021 1.1 Design results Case Description 1 Combination 1 Forces [lb] / Moments [in.lb] Seismic Max. Util.
PAGE 7
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: Page: Specifier: E-Mail: Date: | Concrete - Apr 5, 2021 3 4/5/2021 3.1 Steel Strength Nsa = ESR value f Nsa ³ Nua refer to ICC-ES ESR-3187 ACI 318-08 Eq. (D-1) Variables 2 Ase,N [in. ] futa [psi] 0.08 94,200 Calculations Nsa [lb] 7,306 Results Nsa [lb] f steel f Nsa [lb] Nua [lb] 7,306 0.650 4,749 910 3.2 Pullout Strength Npn = Np f Npn ³ Nua refer to ICC-ES ESR-3187 ACI 318-08 Eq.
PAGE 8
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: Page: Specifier: E-Mail: Date: | Concrete - Apr 5, 2021 4 4/5/2021 3.3 Concrete Breakout Failure Ncbg = (AA ) y Nc Nc0 ec,N y ed,N y c,N y cp,N Nb ACI 318-08 Eq. (D-5) f Ncbg ³ Nua ANc see ACI 318-08, Part D.5.2.1, Fig. RD.5.2.1(b) ANc0 2 = 9 hef y ec,N = ( 1 ' 1+ 2 eN 3 hef ) ACI 318-08 Eq. (D-6) £ 1.0 ACI 318-08 Eq. (D-9) y cp,N c (1.5h ) £ 1.0 c 1.5h = MAX( , 1.
PAGE 9
Hilti PROFIS Engineering 3.0.68 www.hilti.
PAGE 10
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: Page: Specifier: E-Mail: Date: | Concrete - Apr 5, 2021 6 4/5/2021 4.2 Pryout Strength (Concrete Breakout Strength controls) Vcpg [(AA ) y Nc = kcp Nc0 y ed,N y c,N y cp,N Nb ec,N ] f Vcpg ³ Vua ANc see ACI 318-08, Part D.5.2.1, Fig. RD.5.2.1(b) 2 ANc0 = 9 hef y ec,N = ( 1 ' 1+ 2 eN 3 hef ) £ 1.0 ACI 318-08 Eq. (D-9) y cp,N Nb = kc l a,min ACI 318-08 Eq.
PAGE 11
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: | Concrete - Apr 5, 2021 Page: Specifier: E-Mail: Date: 7 4/5/2021 6 Warnings • The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2018, ETAG 001/Annex C, EOTA TR029 etc.).
PAGE 12
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: Page: Specifier: E-Mail: Date: | Concrete - Apr 5, 2021 8 4/5/2021 7 Installation data Anchor type and diameter: HIT-HY 200 + HIT-Z 3/8 Item number: 2018440 HIT-Z 3/8" x 4 3/8" (element) / Profile: Round bars (AISC), 2 1/2; (L x W x T) = 2.500 in. x 2.500 in. 2022793 HIT-HY 200-R (adhesive) Hole diameter in the fixture (pre-setting) : df = 0.438 in. Maximum installation torque: 177 in.
PAGE 13
Hilti PROFIS Engineering 3.0.68 www.hilti.com Company: Address: Phone I Fax: Design: Fastening point: | Concrete - Apr 5, 2021 Page: Specifier: E-Mail: Date: 9 4/5/2021 8 Remarks; Your Cooperation Duties • Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc.