CF1400 DO NOT RETURN PRODUCT TO PLACE OF PURCHASE. IF YOU HAVE ANY QUESTIONS, CALL OUR TOLL FREE HOTLINE: 1-866-902-9690 8:00 am to 5:00 pm, C.S.T., Monday - Friday www.ForceToolsUSA.
IMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS Important safety instructions ............................................................................................... 1 Safety features ..................................................................................................................... 4 Parts and diagram list ........................................................................................................... 5 Assembly and operating instructions...............................
IMPORTANT SAFETY INSTRUCTIONS 8. Always wear safety glasses or goggles when operating or performing maintenance. 9. Always move switch on unit to “OFF” position before connecting or disconnecting cord to electrical outlets. 10.Always turn water supply “on” before turning pressure washer “on” unless draining for storage. Running pump dry causes serious damage. 11.Always hold gun and wand firmly when starting and operating the machine. 12.
PARTS AND DIAGRAM LIST ASSEMBLY AND OPERATING INSTRUCTIONS Tools Required • Philips Screwdriver E A F G B H I C Water Supply (Cold Water Only) Only draw water through the unit. For use with cold water supply only. Water hose must be at least a 1/2” (13 mm) in diameter. Flow rate of water supply must not fall below 2 GPM (gallons per minute) [9.1 lpm (litres per minute)]. Flow rate can be determined by running the water for one minute into an empty 5-gallon (19 L) container.
ASSEMBLY AND OPERATING INSTRUCTIONS 4 3 Attach gun holder and power cord bracket. Attach high pressure hose to the machine’s water outlet (hand tighten only) 5 6 Attach high pressure hose to the gun assembly (hand tighten only). 7 Insert choice of wand to the gun and twist ¼ turn to lock in position. ASSEMBLY AND OPERATING INSTRUCTIONS 8 9 Attach garden hose to water supply and turn water on. Make sure the ON/OFF switch is in the OFF position.
ASSEMBLY AND OPERATING INSTRUCTIONS USING THE ACCESSORIES ASSEMBLY AND OPERATING INSTRUCTIONS 3 Adjustable Spray Nozzle The adjustable spray nozzle can be adjusted from fan to jet. The spray is adjusted from jet to fan spray by turning the nozzle. CAUTION Jet spray adjustment is very aggressive. Do not adjust while spraying. with detergent. Push containers back into storage position.
ASSEMBLY AND OPERATING INSTRUCTIONS SHUTTING DOWN AND CLEANING UP WINTERIZING AND LONG-TERM STORAGE OPTIMUM WINTERIZING PROCEDURE Winterizing your pressure washer will help protect and prolong its life. We strongly recommend you follow the below steps using Pressure Washer Pump Saver (39-8602-0). This will keep the internal parts lubricated, protected from rust, and prevents the pump from freezing. 1 detergent bottle and rinse it thoroughly. 2 Turn the switch to “OFF” (0) position.
CLEANING AND MAINTENANCE Connections Connections on pressure washer hoses; gun and spray wand should be cleaned regularly and lubricated with non-water soluble grease. Spray Tips Only Clogging of the spray tips causes the pump pressure to be too high and cleaning is immediately required. You can clean the spray tips by carefully inserting the needle, or a thin, sharp instrument (i.e. paperclip) into the tip to rid it of deposits.
TROUBLESHOOTING TROUBLESHOOTING Symptom Cause Solution Symptom Cause Solution Output pressure varies high and low. (continued) Discharge nozzle is obstructed. Blow out or remove debris with a fine needle. Motor buzzes but fails to run. Supply voltage below minimum. Verify that only the pressure washer is running on this circuit. System has residual pressure. Turn unit “OFF”, squeeze trigger on spray wand to release pressure, then turn unit “ON”. Voltage loss due to extension cord.
TECHNICAL SPECIFICATIONS WARRANTY Product Warranty Always keep your receipt as proof of purchase. This product has a Parts Replacement, Product Exchange and/or Repair Warranty only. NO REFUNDS will be provided. Please see stores for Product Exchange details Rated Pressure: 1400 PSI Power Source Requirement: 120 V / 60 Hz Electrical Cord: 35’ High-pressure Hose: 19’ Rated Water Flow Rate: 1.
