ENGLISH A.LEDA WASH K5 A.LEDA WASH K10 A.LEDA WASH K20 ® C61401 C61405 C61410 INSTRUCTION MANUAL PR ARY N I M ELI INDEX Page Contents 2 Safety information 3 Unpacking and preparation 4 Installation and start-up 5 Control panel 7 Menu setting 14 Maintenance 16 Optional accessories 19 Technical information 19 Cause and solution of problems 20 Channel functions Congratulations on choosing a Clay Paky product! We thank you for your custom.
SAFETY INFORMATION • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.
UNPACKING AND PREPARATION 1 IST004/001 2 x 183102/802 Packing contents - Fig. 1 2 UNLOCKED 3 ° 90 A.LEDA WASH ° 90 PAN Mechanism Lock and Release (every 90°) - Fig.
INSTALLATION AND START-UP 3 Installing the projector - Fig. 3 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
CONTROL PANEL 5 Mains NB: connecting one “A.leda Wash K5” to the mains, it is possible to connect up to a maximum of 11 “A.leda Wash K5” in parallel at the same time. Connecting to the mains supply - Fig. 5 6 DMX 512 5 PIN 5 4 3 1 2 SCREEN SIGNAL SIGNAL DMX 512 DMX 512 3 PIN SIGNAL 2 SCREEN 1 3 SIGNAL Connecting to the control signal line (DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity.
8 28 28 Reversal of the display - Fig. 8 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off.
MENU SETTING 1 2 Set Up Dmx Address 3 Option Pan / Tilt Invert Pan Information Invert Tilt Channel Mode System Errors Fixture Hours Swap Pan-Tilt System Version Fixture ID Encoder Pan-Tilt Ethernet Interface Silent Mode Board Diagnost.
NOTE: On grey the default options Set Up Dmx Address SET UP MENU DMX ADDRESS NOTE: without the DMX signal the Address (XXX) flashing Allows you to select the DMX ADDRESS. 1) Press - the current DMX Adress appear on the display. 2) Use the UP and DOWN , RIGHT keys to plan the DMX Address. 3) Press to confirm the selection or LEFT to keep current settings. Address xxx F B C E D F Channel Mode CHANNEL MODE Allows you to select a channel arrangement from the two available.
OPTIONS MENU Option Pan / Tilt Invert Pan PAN / TILT Invert pan Used for reversing Pan movement. 1) Press - the current settings appear on the display (On or Off). 2) Use the UP and DOWN keys to enable (On) or disable (Off) PAN inversion. 3) Press to confirm the selection or LEFT to keep current settings. On Off F B C F Invert Tilt D Invert tilt Used for reversing tilt movement. 1) Press - the current settings appear on the display (On or Off).
Setting Default Preset SETTING Used to save 3 different settings of the items in the options menu and relative submenus. 1) Press - “Default preset” appears on the display. 2) Use the UP and DOWN keys to select one of the following configurations: - Default preset (*) - User preset 1 - User preset 2 - User Preset 3 3) Press - “Load preset X” appears on the display. 4) Use the UP and DOWN keys to select: - Load preset X to recall a previously stored configuration.
Board Diagnost. Board 0:PT-3f 1: Ld - Kxx Status Good Good BOARD DIAGNOSTIC Used for displaying the status error of each board installed in the projector: 0: PT-3f (Scheda Pan / Tilt) 1: Ld - Kxx (Scheda LED) Err% 0.00 0.00 DMX MONITOR Used for displaying the projector DMX channel level in bit (Val) and in percentage (Perc).
ADVANCED MENU Advanced To enable the "Advanced Menu" set up the "Access code" (1234) using the UP , DOWN , RIGHT keys. Press - "Menu advanced" appears on the display Code 1234 B F Upload Firmware Transfer the firmware on all the connected fixtures ? Are you sure ? Yes/No Setup Model Changing to a wrong model may damage the fixture. Are you sure ? Yes/No C E UP LOAD FIRMWARE Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
9 1 2 6 3 4 5 Battery removal - Fig. 9 This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 A.
MAINTENANCE 10 3 4 1 2 Opening the covers - Fig. 10 11 4 3 1 2 Removing/Assembling the lens unit - Fig. 11 NB: Apply Loctite 222 (p/n COL002) to the threads of the 3 screws (1) before tightening them. A torque of 0.3N is recommended in order to avoid damaging the zoom movement actuators. A.
12 2 DIM002/001 1 Replacing the line actuator - Fig. 12 NB: It is highly recommended to use the DIM002/001 (1) template whenever it is necessary to replace one of the three Zoom movement line actuators. DIM002/001 ensures the actuator group is centred correctly on the lens plate before tightening the 2 screws (2) that fasten the actuator in place. A.
OPTIONAL ACCESSORIES A.LEDA WASH K5 13 C61452 C61453 1 2 3 Cover - Fig. 13 C61452 - Transparent cover C61453 - Frosted cover 14 C61451 1 3 4 2 Transparent mask - Fig. 14 A.
A.LEDA WASH K10 15 C61455 C61456 1 2 3 Cover - Fig. 15 C61455 - Transparent cover C61456 - Frosted cover 16 C61454 1 3 4 2 Transparent mask - Fig. 16 Continue A.
A.LEDA WASH K20 17 C61458 C61459 1 2 3 Cover - Fig. 17 C61458 - Transparent cove C61459 - Frosted cover 18 C61457 1 3 4 2 Transparent mask - Fig. 18 A.
TECHNICAL INFORMATION 220 (8.66") Power supplies available 100-240V 50/60Hz 155 (6.10") 155 (6.10") Input power • K20 - 750VA • K10 - 450VA • K5 - 170VA Max 1800VA (with 11 A.leda Wash K5 connected in parallel) 245 (9.65") 374 (14.72") LED source LED Osram Ostar RGBW - 15W Average LED life: 50.000 h 381 (15.00") Motors 5 (k10 & k20), 2 (k5) stepper motors, operating with microsteps, totally microprocessor controlled. 320 (12.60") 253 (9.
CHANNEL FUNCTION A.LEDA WASH K5 STANDARD CHANNEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 SHAPES CHANNEL MODE Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset A.
A.
A.
A.LEDA WASH K10 CC CHANNEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CHANNEL MODE Red RedFine Green GreenFine Blue BlueFine White WhiteFine CTO Macro Colour Strobe Dimmer Dimmer fine Pan Pan fine Tilt Tilt fine Function Reset Zoom A.LEDA WASH K20 CC CHANNEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CHANNEL MODE Red RedFine Green GreenFine Blue BlueFine White WhiteFine CTO Macro Colour Strobe Dimmer Dimmer fine Pan Pan fine Tilt Tilt fine Function Reset Zoom A.
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 50% - Tilt 50%) all the others channels stay at 0%. • C.T.O. • RED – GREEN - BLUE - WHITE BIT 255 0 BIT EFFECT COLOUR INSERTED COLOUR EXCLUDED • RED FINE – GREEN FINE – BLUE FINE – WHITE FINE BIT EFFECT 255 0 Note: If CTO channel is active, the WHITE channel is disabled. A.
• MACRO COLOUR • STOP / STROBE LEE REFERENCE 207-255 197 Alice Blue 128 255 143 0 191-206 181 Congo Blue 77 0 255 0 184-190 174 Dark Steel Blue 181 255 95 0 180-183 170 Deep lavender 255 168 64 0 179 169 Lilac Tint 255 199 49 0 175-178 165 Daylight Blue 82 214 90 0 COLOUR MACRO BIT VALUE R G B W BIT BIT EFFECT 252 - 255 239 - 251 226 - 238 213 - 225 208 - 212 207 OPEN RANDOM FAST STROBE RANDOM MEDIUM STROBE RANDOM SLOW STROBE OPEN FAST PULSATION 108 104 -
• PAN Operation with option InvertPan Off (Tilt conventionally represented at 14% and option Invert Tilt G • TILT Operation with option InvertPan Off (Tilt conventionally represented at 14% and option Invert Tilt G GOff) GOff) BIT BIT 255 255 0-255 Bit: 2.65 sec (K20) 0-255 Bit: 2.01 sec (K10) 0-255 Bit: 1.41 sec (K5) 0-255 Bit: 1.45 sec (K20) 0-255 Bit: 0.87 sec (K10) 0-255 Bit: 0.
• FUNCTION DIMMER CURVE 4 - S BIT 251 – 255 103 – 250 98 – 102 93 – 97 88 – 92 83 – 87 78 – 82 73 – 77 68 – 72 63 – 67 58 – 62 53 – 57 48 – 52 43 – 47 38 – 42 25 – 37 12 – 24 0 – 11 EFFECT Reset to defult Unused Range Halogen Lamp Simulation, type 5 (2500 W) Halogen Lamp Simulation, type 4 (2000 W) Halogen Lamp Simulation, type 3 (1200 W) Halogen Lamp Simulation, type 2 (1000 W) Halogen Lamp Simulation, type 1 (750W) Halogen Lamp Simulation OFF (Default) RGBW Gamma curve 3 – gamma = 2.
SHAPE SELECTION - SHAPE SPEED - SHAPE OFFSET BIT 32-255 31 30 29 28 27 26 25 24 SHAPE SELECTION Reserved Two rotating arcs of different colors and direction Two rotating arcs of different colors Two rotating bars of different colors Triangle Half moon Bar (2 arms) Fan (3 arms) Rainbow 2, fixed speed with variable color offset. On K5 On K10 No No Yes Yes On K20 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes RANDOM COLORS *1 SHAPE OFFSET N.a. N.a. N.a.
Macro Off DMX channel value: from 0 to 7. No shape effects activated. Turns off any previously selected shape. Static Rings DMX channel value: from 8 to 14. The ring or rings used by the macro are turned on with the foreground colour (Shape Red+Shape Green+Shape blue+Shape White). Avaliable combinations: Ring 1 On, Ring 2 On, Ring 3 On (Aleda K10, K20 only), Ring 4 On (Aleda K20 only),Ring 1+2 On, Ring 1+3 On (Aleda K10, K20 only), Ring 1+4 On (Aleda K20 only).
• SHAPE SMOOTHING • ZOOM BIT BIT 255 246-255 245 244 243 EFFECT WIDE BEAM EFFECT Smooth, fading curve with automatic gamma * Smooth, fading curve gamma 2 Smooth, fading curve gamma 1,993 Smooth, fading curve gamma 1,986 0-255 Bit: 0.68 sec (K20) 0-255 Bit: 0.69 sec (K10) 18 17 16 0-15 0 Smooth, fading curve gamma 0,513 Smooth, fading curve gamma 0,506 Smooth, fading curve gamma 0,5 Snap * Automatic gamma is calculated based on background intensity to auto-adapt the shape’s fade.
• SHAPE TRANSITION BIT FADING TIME BIT 255 4000 ms 199 2600 ms BIT 143 1480 ms 87 650 ms 254 3970 ms 198 2580 ms 142 1460 ms 86 640 ms 253 3950 ms 197 2560 ms 141 1440 ms 85 630 ms 252 3920 ms 196 2530 ms 140 1430 ms 84 620 ms 251 3890 ms 195 2510 ms 139 1410 ms 83 610 ms 250 3860 ms 194 2490 ms 138 1390 ms 82 600 ms 249 3840 ms 193 2470 ms 137 1380 ms 81 590 ms 248 3810 ms 192 2450 ms 136 1360 ms 80 570 ms 247 3780 ms 191 2420 ms 135
A.LEDA WASH K5 A.LEDA WASH K10 LED reference number for pixel mapping TILT: channel 16 at 80% LED reference number for pixel mapping TILT: channel 16 at 80% 13 14 12 15 4 11 LED 3 2 16 6 1 10 17 2 6 1 LED 3 5 4 5 7 18 9 8 7 19 A.LEDA WASH K20 LED reference number for pixel mapping TILT: channel 16 at 80% 28 29 30 27 26 13 14 4 5 31 12 15 25 11 LED 3 24 32 16 6 1 33 10 17 2 23 7 9 22 34 18 8 19 20 37 21 35 PRELIMINARY 04/13 Cod.