Use and Care Manual

Classic Coatings Systems • 255 Citation Circle, Corona, CA 92878
© 2015 Classic Coatings Systems Inc. All rights reserved.
A PREMIUM SEMI-TRANSPARENT DECORATIVE STAIN
DESCRIPTION
TYPICAL USAGE
Simple Stain Concentrate
Classic Simple Stain Concentrate can be used anywhere architectural concrete is desired. Both
interior and exterior, on almost any cementitious surface, whether it be gray or color harden
concrete, stamped or textured concrete, micro-toppings or overlays. It can be used as an entire
surface colorant or just as an accent border or detail. It may be used on both new and existing
substrates. Typically used as ooring in restaurants and food service areas, bars, hotels, casinos,
retail stores, malls, art studios, movie theaters, museums, pool decks, automobile showrooms,
residential ooring, and more. Classic Stains
may also b e used as a means to color poured in place
concrete; both smooth or with a form linear, tilt up wall, stone-face plaster, GFRC, and faux rock.
Note: In some cases if a reaction cannot be achieved, the substrate may need to be resurfaced
with a cementitious topping such as Classic Micro Topping (indoor applications only) and Classic
Stampable Overlay (outdoor applications only). The benet to resurfacing is to provide a virgin
canvas without the eect of patches, repairs, existing stains, mastics, glues, oils, etc.
Protects and preserves against wear and
exposure when sealed
Multiple colors can be used for uni
que and
beautiful results
Semi-transparent
finish
Can be used on interior and exterior surfaces
UV stable and Zero VOC
Low cost, easy to use, and low maintenance
In most cases, it can be sealed with a Classic
Coatings Sealer on the same day
Do not dilute with more than 5 quarts of
distilled water
Not for use on self-leveling cement or light
weight concrete
Must be installed over a clean dry surface that
should feel like it is under 100 grit sandpaper
Moisture & efflorescence must be removed
before applying stains or sealers
ADVANTAGES LIMITATIONS
REVISED: FEBRUARY 2024
Never apply adhesive tape
over stained or
sealed surfaces as it may cause damage. Once
sealed, allow 5-7 days before parking.
Classic Simple Stain Concentrate is an easy to use water-based stain that enhances the
aesthetic of many different types of surfaces. Multiple colors can be used to create unique
and beautiful results. This advanced formula allows color to reach its full potential
almost immediately upon application. Color may be built up without the worry of damaging
the concrete like acid stain does. Classic Simple Stain Concentrate is UV stable and has zero
VOC. After applying the first coat, you only have to wait 20 - 30 minutes to apply the
second coat at 77ºF. All colors may be used on interior and exterior surfaces
in a wide range of environments. Apply a Classic Coatings Systems water-based
sealer over the stain to protect the color and make it more vibrant. It is highly
recommended to test a sample area first. We recommend mixing 1 quart of Classic Simple
Stain Concentrate with 4 quarts of distilled or deionized water. New 4" concrete must cure
for 28 days before the stain can be applied.
COVERAGE:
1
quart (1.06 Liters)
covers approximately
600-700 sq. ft. with one
coat depending on the
surface and application
method.
PACKAGING:
1
quart bottle
S
TORAGE:
1. S
tore in a cool, dry
location.
2. Store out of direct
sunlight
3. Protect from freezing
weather and other
damage.
4.
Store at a temperature
between 40ºF (4ºC) and
90ºF (32ºC).
SHELF LIFE:
3 years - Unopened
COLOR:
See color chart
Clean surfaces with Classic Organic Concrete
Cleaner. Follow label instructions
Visit our Youtube channel for
How-to Videos and our Instagram
for inspiration!
@ClassicCoatingSystems
@ClassicCoatingsSystems
@SimpleStains