Division of IMAGE 14 120V Operator's Manual READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
Table of Contents Operator Safety Instructions ............................................................................................................ 3 Introduction & Machine Specifications ............................................................................................. 5 Instructions - Power Supply 120 Volt ................................................................................................ 6 Machine Controls ..................................................................
IMPORTANT SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
IMPORTANTES MESURES DE SECURITE AVERTISSEMENT: Pour réduire les risques d'incendie,de choc électrique ou de blessure: 1. Ne pas laisser l'appareil sans surveillance lorsqu'il est branché. Débrancher lorsque l'appareil n'est pas utilisé et avant l'entretien. 2. Pour réduire les risques de choc électrique, utiliser à l'intérieur seulement. 3. Ne pas permettre aux enfants de jouer avec l'appareil. Une attention particuliére est 4.
DANGER: Machines can cause an explosion when operated near flammable materials and vapors. Do not use this machine with or near fuels, grain dust, solvents, thinners, or other flammable materials. WARNING: You must have training in the operation of this machine before using it. READ THE INSTRUCTION BOOK FIRST. WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders.
120 VOLT, 50/60 CYCLE MACHINES GROUNDING INSTRUCTIONS This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipmentgrounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
THE CONTROLS The Vacuum/Accessory/Pump Switch This switch is located on the handle. To turn the vacuum motor on, place the switch in the middle position. To turn pump, brush, and vacuum motor on, place the switch in bottom position. (Figure 2, #1) 1 2 The Vacuum Hose Connector The vacuum hose connector is on the right hand rear of the machine. (Figure 2, #2) The Solution Hose Connector The solution hose connector is located on the bottom center of the machine.
HOW TO CLEAN AN AREA OF CARPET CAUTION: The recovery tank is equipped with a mechanical shut-off float switch. When the recovery tank becomes full the machine will no longer recover water. Turn the vacuum/accessory and spray/brush/switch to the "O" position before emptying the recovery tank. NOTE: When using the extractor to clean carpets, follow this procedure: 1. Do not walk on freshly cleaned carpets for at least four hours or until the carpet is dry to touch. 2.
To clean a larger area of carpet, follow this procedure: (See Figure 4) 3 1 1. Begin at the right-hand corner of the carpet. 2. Make a pass halfway along the edge of the carpet. Pull the machine backward at a steady speed. 3. Move to the edge of the carpet. Make another pass next to your first pass. 4. As you make more passes, overlap one inch of the area already cleaned. Make each pass four inches different in length to prevent making a line in the center of the carpet. 5.
MAINTENANCE (cont) How To Attach The Auxiliary Floor Tool To attach the auxiliary floor tool, follow this procedure: 1. Remove the vacuum hose from the recovery tank. 2. Connect the auxiliary floor tool vacuum hose to the recovery tank and to the auxiliary tool. 3. Move and hold the brush height lever (figure 5) away from the auxillary connection. Make connection and release brush height lever (will rest against connection). See figure 5a. 4. Connect the solution hose to the machine and to the floor tool.
How to Prevent Damage From Freezing Temperatures To prevent damage from freezing temperatures, follow this procedure: 1. Remove any solution remaining in the solution tank. 2. Make sure the machine and pump are completely dry. 3. Pour windshield-type antifreeze into the solution tank until the screen in the filter is covered. 4. Turn on the vacuum/accessory switch and the spray/ brush switch for 30 seconds. 5. Remove antifreeze solution from the system before using the extractor. 6.
NOTES Page 12 Clarke® Operator's Manual - Image 14
Division of Image 14 Section II Parts and Service Manual (70088A) Clarke® Operator's Manual - Image 14 Page 13
AUTHORIZED PERSONNEL MAINTENANCE To Access Pump/Brush Unit Brush Maintenance 1. Remove six (6) screws in rear plate that secure solution tank to machine. 1. Remove (6) screws in rear plate that secure solution tank to machine. 2. Remove solution tank from machine. 2. Remove solution tank from machine. 3. Disconnect pump ground wire from ground screw. 3. Remove screws holding brush cover on. Remove brush cover. 4. Remove solution hoses. 5.
HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM CAUSE ACTION The machine will not run. 1. Machine does not have power... 1. Make sure the machine is connected to the correct frequency and voltage, and all connections are tight. There is no suction. 1. Vacuum motor may not be running... 1. Be sure the vacuum/accessory switch is at the vacuum/accessory position. 2. 2. Remove and clean lint screen on vacuum stand pipe. Vacuum intake screen clogged. 3. There may be a loose motor connection. 3.
Clarke® Image 14 Drawing and Parts List Final Assembly 4/98 2 10 13 1 3 4 5 6 12 7 8 9 11 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 Page 16 Part No. Page 15 Page 16 Page 17 Page 18 80013A Page 19 82509A 58540A 925004 68504A 85397A 85398A 57427A Description Handle Assembly Recovery Tank Assembly Solution Tank Assembly Brush/Pump Assembly Bolt, Shoulder Main Frame Assembly Pin, Clevis Spacer Pin, Cotter Drain, Preventor Screw, 10-24 x 3/8 S.S. Screw, ¼-20 S.S.
Clarke® Image 14 Drawing & Parts List, Handle Assembly 4/98 Form #15347A 6 1 6 4 5 3 2 To main frame assembly Ref. Part No.
Clarke® Image 14 Drawing and Parts List, Recovery Tank Assembly 9/02 Form #10450A 7 8 9 18 10 1 13 6 11 2 5 14 3 15 12 4 17 16 Page 18 Ref. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 692409 86303A 81901A 30290A 962954 55670A 31803A 50805A 34286A 57425A 85606A 84237A 962987 34288A 980982 85397A 69893A 920224 Chain, Cover Screw, #10-24 x 1.
Clarke® Image 14 Drawing and Parts List, Solution Tank Assembly 9/02 Form #10451A 1 2 20 3 17 4 16 5 6 13 15 23 5 21 7 8 13 14 12 To Vacuum Motor 10 18 22 19 To Recovery Tank *Note: Service Item Only Ref. Part No.
Clarke® Image 14 Drawing and Parts List, Brush/Pump Assembly 9/01 Form #17651A 1 6 2 5 28 4 27 24 23 3 22 25 26 4 29 21 5 6 11 20 9 2 7 12 18 12 16 17 14 15 13 11 30 13 Ref. Part No.
Clarke® Image 14 Drawing and Parts List, Main Frame Assembly 9/01 Form #17650A 48 2 47 25b 48 50 46 49 44 38 25a 2 12 2 4 1 45 11 28 5 6 30 26 7 4 8 10 49 5 9 13 10 14 27 39 25 11A 34 24 49 43 23 35 37 40 42 27 15 29 41 32 28 18 31 17 22 21 20 19 33 Ref. 1 2 4 5 6 7 8 9 10 11 11a 12 13 14 15 16 17 18 19 20 21 22 23 24 25 16 Part No.
Clarke® Image 14 115V Drawing and Parts List 10/97 Brush/Pump Unit 3 2 1 6 5 4 Ref. Part No.
Clarke® Image 14 120 Volt Connection Diagram 3/98 Clarke® Operator's Manual - Image 14 Page 23
Clarke® Image 14 120 Volt Electrical Schematic 03/98 Page 24 Clarke® Operator's Manual - Image 14
Authentic Clarke® Products 9/01 6 3 7 8 9 4 10 2 5 1** Ref 1 2 3 4 5 6 7 8 9 10 11 ASM NI Part No. 30108A 59231A 59230A 59229A 59232A 59228A 398426 398425 398427 55183A 52953A 55173A 68204A Description Adaptor, 2" to 1½ RM-4P Tool Assembly RM-8P Tool Assembly RM-12M Tool Assembly Hide-A- Hose 10' RM-4M Tool Assembly Defoamer Extractor, Concentrate Traffic Lane/Spot Cleaner Hide-A-Hose 20' General Purpose Spot Cleaner 4" Hand Tool and 10' Hose Asm.
NOTES
PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St.
Clarke® U.S. WARRANTY This Clarke Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke's Maintenance and Operations Instructions. This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear parts such as electrical cable, rubber parts, hoses and motor brushes.