IWA-200 IWA-220 Infrared Wall Mounted Amplifier System Operation manual ISO 9001 R EG ISTER ED IS O 140 01 ISO 14001 R EG ISTER ED OHSAS 180 01 OHSAS 18001 GREEN PRODUCT
Thank you for purchasing our infrared wireless microphone system. Please be sure to read the user's manual thoroughly and keep it for future reference. Cautions Do not cover the infrared emitter area of the wireless transmitter or the surface of the infrared sensor. Do not use the transmitter too close to speakers to prevent feedback. Do not replace the battery when power is on. Do not install near heat source or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
ISO 9001｜ISO 14001｜OHSAS 18001 Connections External sensor or IWA-200/220 amplifier AC adaptor Installing the external sensor IS-20A (wall/ceiling-mount type) fixing holder with a screw angle-adjustable shaft Find the best position for sensor to be mounted as illustrated for optimal coverage. Mount the external sensor IS-20A on a wall or ceiling.
Installing the external sensor IS-30A (ceiling-mount type) In an ordinary space such as a classroom 1. Locate the IS-30A sensor in the middle of the ceiling, as illustrated below 2. Connect the sensor cable to the receiver. 3. Turn on the IR system and amplifier then operation can be started. In a larger space such as a fitness center 1. Locate 2 or 3 IS-30A sensors on the suggested positions on the cater-corner of the ceiling, as illustrated below. 2. Connect all sensor cables to the receiver. 3.
ISO 9001｜ISO 14001｜OHSAS 18001 Two IS-20A wall sensors rostrum IS-20A IRX2 IS-20A IS-20A IRX2 please be careful of the angles IS-20A rostrum IS-20A 2.5m 1.5m rostrum IRX2 Ex: 10x10 sqm classroom IS-20A 3~3.5m 1.
Handheld/Pendant IR Transmitter IWH-401 Parts and functions 1 2 3 4 5 7 8 6 9 1. 2. 3. 4. Cartridge screen. Infrared emitter. IR ray radiates from here. Do not block or hold this part of the body. Anti-rolling color ring. Status LED: Bicolor LED will glow when switch is put to ON. Green: Battery is full and transmitter is in normal mode. Red: Battery is weak and will shut off soon. Please charge the battery. 5. Power switch: Slide to turn transmitter on or off. 6. Battery compartment.
ISO 9001｜ISO 14001｜OHSAS 18001 Handheld/Pendant IR Transmitter ITX2 Parts and functions 1 2 3 4 5 11 6 7 8 9 10 12 1. 2. 3. 4. Cartridge screen. Release buttons of pendant holder. Channel selector. Channel A: 2.08MHz, Channel B: 2.54MHz Bicolor status LED. Green: Battery full. Red: Battery weak and needs recharging. 5. Power on-off/audio mute switch. 6. Infrared emitter. IR ray radiates from here. Do not block or hold this part of the body. 7. Line input (Φ3.5mm) for external audio input. 8.
Handheld IR Transmitter IWH-301 Parts and functions 1 2 3 6 5 7 4 8 1. Cartridge screen. 2. Status LED: Bicolor LED will glow when switch is put to ON: Green: Battery is full and transmitter is in normal mode. Red: Battery is weak and will shut off soon. Please charge the battery. 3. Power switch: Slide to turn transmitter on or off. 4. Infrared emitter. IR ray radiates from here. Do not block or hold this part of the body. 5. Battery compartment. Turn the battery cover counterclockwise and pull out.
ISO 9001｜ISO 14001｜OHSAS 18001 Pendant IR Transmitter IWM-402 Parts and functions 1 4 9 7 2 3 5 6 11 8 10 Mic in (Φ2.5mm). Headset or lavalier microphone. Power switch. Charging port. IR emitter area. IR ray radiates from here. Do not block or hold this part of the body. Status LED: Bicolor LED will glow when switch is ON. Green: Battery is full and transmitter is in normal mode. Red: Battery is weak and will shut off soon. Please charge the battery. 6. Mute.
-9-
ISO 9001｜ISO 14001｜OHSAS 18001 -10-
CHIAYO ELECTRONICS CO.,LTD. Http://www.chiayo.com.tw｜Email: sales@chiayo.com.
