Specifications

ManualsBrandsCentral Pneumatic ManualsDo-It-Yourself tools92208

AIR IMPACT WRENCH

AND

RATCHET SET

ASSEMBLY AND OPERATION

INSTRUCTIONS

Model 92208

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

2004 by Harbor Freight Tools

of this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

REV 11h

Summary of content (9 pages)

PAGE 1
® AIR Impact wrench and ratchet set Model 92208 ASSEMBLY and OPERATIoN INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com To prevent serious injury, Read and understand all warnings and instructions before use. Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
PAGE 2
Specifications 1 Air Inlet /4”-18 NPT (All tools) Maximum Operating Pressure 90 PSI (All tools) Air Ratchet Dimensions 1-5/8” D x 10-3/8” L Drive Size 3/8” Sq. Maximum Torque Output 50 Ft. Lbs. Air Consumption 4 CFM No Load RPM 150 (Reversible) Impact Wrench Dimensions 2-3/4” W x 7-1/4” L x 8” H Drive Size 1/2” Sq. Maximum Torque Output 240 Ft. Lbs.
PAGE 3
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 9. Maintain tools with care. Keep tools clean for better and safer performance.
PAGE 4
21. Compressed air only. Never use combustible gas as a power source. 22. Use both hands. The torque generated from these tools can cause the tools to break free of your grasp, causing serious injury and damage. Always operate the tools with both hands. 23. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.
PAGE 5
Air Impact Wrench Operation Warning!! This Impact Wrench supplies FIGURE 1 powerful torque and is designed to be operated with two hands. Failure to operate the Impact Wrench with two hands may result in serious injury. Air Inlet (10) Note: Turn off your air compressor and disconnect the air hose when you are changing sockets. After you attach the socket, attach the air hose and turn the air compressor on. Air Regulator 1. Select the appropriate size 1/2” (12) drive socket for your needs. 2.
PAGE 6
Air Ratchet Operation FIGURE 2 Reverse Switch (21a) Air Inlet Trigger (35a) Anvil (22a) Warning! Do not use a “cheater” or other extension to increase torque for this tool. Do not exceed the maximum torque rating on this tool. Warning! Disconnect the Ratchet from the air source when attaching and removing sockets. There is no safety lock mechanism on this tool; always disconnect from the air source when not in use. Refer to the photograph above. 1. Attach a 3/8” drive socket to the Ratchet Anvil (22a).
PAGE 7
Air Impact Wrench Assembly Diagram Parts List Part Description Part Description Part Description 1 Housing 16 Screw 31 Spring 2 Valve Sleeve 17 Anvil Bushing 32 Pin 3 Reverse Valve 18 Anvil (1/2”) 33 Rear Gasket 7 4 Trigger 19 Hammer Cage 34 Rear Cover 1 5 Pin 20 Hammer Pin 35 Washer 9 6 Bushing 21 Hammer Dog 36 Screw 5 7 Valve Stem 22 Drive Cam 37 Rubber Cover 11 8 Steel Ball 23 Cylinder Pin 38 Exhaust Deflector 3 9 Spring 24 Cylinder 39 Scr
PAGE 8
Assembly Diagram A - Air Ratchet Note:All part numbers referred to on this diagram are indicated with a suffix of a. For example, part 1a refers to part 1 on this diagram. Parts List A Part Description Qty. Part Description Qty. Part Description Qty.
PAGE 9
0 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.