Owner manual

ManualsBrandsCCI Thermal Technologies ManualsToolsSF-1 - Stratafa Forced Convection Fan for Infrared Heaters

1.0 SPECIAL NOTICES

1.1 The following special notices highlight

important information in the installation

and maintenance sections. Each serves a

special purpose and is displayed in the

format shown:

This symbol indicates a potentially hazardous

situation, which, if not avoided, can result in

personal injury or damage to the equipment.

This symbol indicates a potentially hazardous

situation, which, if not avoided, may be a

shock hazard.

This symbol indicates an imminently

hazardous situation, which, if not avoided,

could result in death or serious injury.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, EXCESSIVE VIBRATION,

SERVICE OR MAINTENANCE CAN CAUSE

PROPERTY DAMAGE, INJURY OR DEATH.

READ THE INSTALLATION, OPERATING

AND MAINTENANCE INSTRUCTIONS

THOROUGHLY BEFORE INSTALLATION

OR SERVICING THIS EQUIPMENT.

STANDARD APPLICATIONS

STRATAFAN™

INSTALLATION & OPERATION INSTRUCTIONS

E-mail: info@ccithermal.com www.ccithermal.com

Date of Issue: January 2013

11416.Rev.3.01

Printed In Canada

2.0 CERTIFICATION

2.1 Stratafan™ model SF-1 is certied

intrinsically safe by the Canadian Standards

Association for use in Class I, Divisions

1 and 2, Group D; Class I, Zone 1 and 2,

Groups IIA hazardous (classied) locations.

The unit has a temperature code of T2C at

a maximum ambient temperature of 40°C

(104°F) and must be used in conjunction with

a Cata-Dyne™ WX or MKII catalytic heater.

3.0 INTENDED USE

3.1 The Cata-Dyne™ Stratafan™ can be used in

industrial locations to promote higher overall

air temperature, lower humidity, reduced

condensation and ice build up.

3.2 The Stratafan™ thermoelectric fan is

designed and intended for use only with

Cata-Dyne™ WX or MKII catalytic heaters,

a product by CCI Thermal Technologies Inc.

Use of the Stratafan™ with any other style of

heater will void the product certication and

may pose a risk of property damage, injury

or death. Under no circumstances should

the Stratafan™ be used with any alternative

catalytic heater, gas stove, wood stove, etc.

C US

ISO 9001

CAUTION

WARNING

Summary of content (6 pages)

PAGE 1
standard applications stratafan™ INSTALLATION & OPERATION INSTRUCTIONS 1.0 sPECIAL nOTICES 1.1 CAUTION CAUTION WARNING 2.0 The following special notices highlight important information in the installation and maintenance sections. Each serves a special purpose and is displayed in the format shown: CERTIFICATION 2.1 This symbol indicates a potentially hazardous situation, which, if not avoided, can result in personal injury or damage to the equipment.
PAGE 2
4.0 OPERATION 4.1 5.2 Top Installation: Startup: (i) Install the Stratafan™ in the desired location as per the Installation Instructions section of the Installation & Operation Instructions. The fan will start operation when the unit absorbs sufficient heat from the heater. Under normal operating conditions with the heater at steady-state temperature, the fan should reach continuous operating speed within approximately 5 minutes. The Stratafan™ does not require any assistance for start-up. 4.
PAGE 3
5.3 Side Installation Cata-Dyne™ Z - Mounting Bracket: 5/16” x 1” hex head bolt use a 5/32” allen key (i) Remove the 1.5” socket head cap screws from the back of the Stratafan™ using a 5/32” allen key. Flip the rear mounted clamp bracket. Install the included 2.5” long hex head socket cap screws using a 5/32” allen key. This will leave a 1/2” (12.7 mm) gap between the clamp and the Stratafan™ unit. (ii) Align the hole in rear clamp bracket with any available holes on the Z-bracket.
PAGE 4
5.4 Side Installation Cata-Dyne™ Standard Mounting Bracket: use a 5/32” allen key 5/16” hex head bolt (i) Remove the 1.5” hex head cap screws from the back of the Stratafan™ and flip the rear mounted clamp bracket. Install the 2.5” long, 5/32” socket cap screws using a 5/32” allen key. This will leave a 1/2” (12.7 mm) gap between the clamp and the Stratafan™ unit.
PAGE 5
.5 Bottom Installation: 6.0 7.0 REPAIRS 6.1 Under no circumstances should users attempt to repair the Stratafan™. User repair will void the product warranty and the CSA Intrinsic Safety Certification. 6.2 Contact the original sales distributor to arrange for product repair. RETURN GOODS POLICY 7.1 (i) Place on top of the unit with the heat collection plate directly in front of the pad surface. CAUTION do not put stratafan™ over top of the supporting rail. 8.
PAGE 6
5918 Roper Road, Edmonton, Alberta, Canada T6B 3E1 Phone: (780) 466-3178 Fax: (780) 468-5904 PLEASE ADHERE TO INSTRUCTIONS PUBLISHED IN THIS MANUAL. Failure to do so may be dangerous and may void certain provisions of your warranty. For further assistance, please call: 24 Hr. Hotline: 1-800-661-8529 (U.S.A. and Canada) Please have model and serial numbers available before calling.