Installation & Assembly

ManualsBrandsCanora Grey ManualsFurnitureAgnew Kitchen Island

Part List

Hardware List

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Kitchen Island

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

Cam Lock Screw

8 pcs. (+1 extra)

Cam Lock

8 pcs. (+2 extra)

M6x35

Head Cap Bolt

12 pcs. (+1 extra)

Spring Washer

8 pcs. (+1 extra)

Flat Washer

8 pcs. (+1 extra)

Adjustable Pin

4 pcs. (+1 extra)

M4x20

Machine Screw

8 pcs.

Knob

4 pcs.

Handle

2 pcs.

Cross Dowel

4 pcs. (+1 extra)

M6x50

Head Cap Bolt (long)

12 pcs. (+1 extra)

Top

1 pc.

Summary of content (7 pages)

PAGE 1
Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. Hardware List Hex Wrench 1 pc. Cam Lock Screw 8 pcs. (+1 extra) Small Hex Wrench 1 pc. Cam Lock 8 pcs. (+2 extra) M6x35 Head Cap Bolt 12 pcs. (+1 extra) Cross Dowel 4 pcs.
PAGE 2
Assembly Instructions 2/6 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Remove drawer from Top (A). A Cam Lock Screw STEP 2 Place Top (A) and Side Panels (D) on a soft cloth.
PAGE 3
Assembly Instructions 3/6 STEP 3 Attach Side Panels (D) to Rails (H) with Cam Locks. (See Figure 2) Cam Lock Attach unit to Top (A) with Cam Locks. D H D H A Figure 2 Head Cap Bolt STEP 4 G G F E Attach Stretchers (G) to Posts (E) and (F) with Head Cap Bolts.
PAGE 4
Assembly Instructions 4/6 Head Cap Bolt E F I I I F I E STEP 5 Attach Shelves (I) to unit from Step 3. Attach post units to unit with Head Cap Bolts. Head Cap Bolt (long) Head Cap Bolt STEP 6 B Cross Dowel Attach Base (B) to unit with Cross Dowels, Head Cap Bolts (long) and Head Cap Bolts. (See Figure 4).
PAGE 5
Assembly Instructions 5/6 Head Cap Bolt (long) Spring Washer Flat Washer STEP 7 Attach Feet (C) to unit with Flat Washers, Spring Washers and Head Cap Bolts (long). (See Figure 5) C C C C Figure 5 STEP 8 Turn unit over to its upright position. Insert Adjustable Pins into side panels at desired level. Figure 6 Place Shelf (J) into position. Figure 7 Attach Doors (K) and (L) to unit by sliding door hinges into side panel hinges.
PAGE 6
Assembly Instructions 6/6 STEP 9 Machine Screw Handle Attach Handles to drawer with Machine Screws. STEP 10 Slide drawer into position. Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 8) Note: Unit must be level to work properly.
PAGE 7
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.