User Guide
Table Of Contents
- Contents
- About this guide
- Installing
- Printing
- Printing documents
- Changing print settings (Opening the settings dialog box)
- Setting the paper type and print quality/[Main] tab
- Setting page size and number of copies/ [Page Setup] tab
- Printing on a custom paper size
- Enlarging/reducing to fit the paper size (Fit-to-page printing)
- Scaled printing
- Printing multiple pages on one sheet (Page layout printing)
- Poster printing
- Duplex printing and binding a document into a booklet (Booklet printing)
- Borderless printing
- Duplex printing
- Setting background printing (Windows 98/Me only)
- Selecting a stamp/[Stamp/Background] tab
- Selecting a background/[Stamp/Background] tab
- Setting special effects/[Effects] tab
- Saving settings as a print profile/[Profiles] tab
- Cleaning and machine settings/[Maintenance] tab
- Checking the status of the machine with the BJ Status Monitor
- Sharing the printer and using it on a network
- Scanning
- Scanning with the operation panel
- Scanning with the MP Toolbox
- MP Toolbox settings
- Scanning an image from an application
- Creating one PDF file from two or more pages
- Scanning two or more small documents at one time
- Setting preferences and scanning with ScanGear MP
- Switching between Simple Mode and Advanced Mode
- Using Simple Mode
- Using Advanced Mode
- Advanced Mode Toolbar
- Advanced Mode - Specifying the parameters of a scan
- Advanced Mode - [Main] tab settings
- Advanced Mode - [Settings] tab settings
- Advanced Mode - [Settings 1] tab settings in the [Preferences] dialog box
- Advanced Mode - [Settings 2] tab settings in the [Preferences] dialog box
- Advanced Mode - [Color] tab settings
- Advanced Mode - [Color] tab - Brightness and contrast
- Advanced Mode - [Color] tab - Gamma
- Advanced Mode - [Color] tab - Histogram
- Advanced Mode - [Color] tab - Tone curve
- Advanced Mode - [Halftone] tab
- Determining resolution
- Scanning with the WIA driver (Windows XP only)
- Faxing (Fax model only)
- Sending a fax
- Registering or editing a recipient in the Address Book
- Troubleshooting
- Glossary
- Index
![](/manual/canon/multipass-mp360/user-guide-english/images/img-28.png)
26
[Dither]
– Dither creates halftones using pixels arranged in a fixed pattern. Dithering is suitable for graphs
and charts with well-defined color boundaries.
[Diffusion]
– Diffusion creates halftones by arranging image pixels randomly. Diffusion is suitable for
photographs and graphs that require a fine color gradation.
IMPORTANT
With some combination of [Media Type] and [Quality], certain halftoning methods cannot
be selected.
z [Reduce spool data size] (Windows 2000/XP only)
You can reduce the size of printing data when spooling. Select this check box when the
document is not printed properly (in such case as the image is not printed).
NOTE
You may not be able to see the effect of this setting depending on the application you are using.
3 Click [OK].
Setting a custom color adjustment
Normally color is adjusted in an application. To make finer adjustments, set up color balance in the
dialog box below. In the photograph and illustration at the upper left of the dialog box, you can
roughly check the changes made.
The following changes are made in the [Printer Properties] or [Printing Preferences] dialog box, on
the [Main] tab.
To open the [Printer Properties] or [Printing Preferences] dialog box J “Changing print settings
(Opening the settings dialog box)”
1 In [Color Adjustment], select [Manual], then click [Set].
2 In the [Manual Color Adjustment] dialog box, move the sliders to the left or right to
adjust color balance and intensity.
3 Click [Enable ICM] to activate the color correction function built into Windows.
If you clear this setting, in [Print Type], select the document type to be printed, and in [Brightness],
select a level of the brightness when printing.
NOTE
ICM stands for Image Color Management.
4 Click [OK].
FWsoft-E.book Page 26 Friday, October 17, 2003 2:01 PM