MultiPASS MP370/360 Set-Up Sheet

ManualsBrandsCanon ManualsAll in One PrinterMultiPASS MP360

Set-Up Sheet

Thank you for purchasing the Canon MultiPASS MP370/360. To prepare your

machine for use, please follow the instructions in this

Set-Up Sheet before referring to

any other documentation.

READ THIS SHEET FIRSTREAD THIS SHEET FIRST

Do not connect the USB cable until , "Connect the USB

cable."

IMPORTANT

Setup procedures

Start

Setup flow

Setup procedures

End

This side explains the setup procedure for use without connecting to a computer. <Check packed contents, install and adjust machine>

This side explains the setup procedure for use by connecting to a computer. <Install MP Drivers and Utility Software>

You can use the copy, photo print (MP370) functions.

You can use the print, scan functions.

Connect power

cord

Install Utility Software

Install print head

Install MP Drivers

Install ink tanks

Connect USB cable

Load print media

Align print head

Unpack and install

the machine

Unpack and install the machine.

1 Carefully remove all items from the box.

NOTE

• When removing the machine from the

box, take sufficient care not to drop it.

2 Remove the protective material.

NOTE

• After removing the protective material,

do not lift the machine by grasping the

scan unit.

Hold the bottom side.

3 Place the machine on a flat surface.

• Be sure to hold the machine by the

sides. Set nothing in front of the

machine.

4 Remove all shipping tape from the

exterior of the machine.

• After removing the tape, remove the

protective sheet.

Do not grasp the

scan unit.

HT3-2142-000-V.1.0

Summary of content (8 pages)

PAGE 1
HT3-2142-000-V.1.0 Set-Up Sheet READ THIS SHEET FIRST Thank you for purchasing the Canon MultiPASS MP370/360. To prepare your machine for use, please follow the instructions in this Set-Up Sheet before referring to any other documentation. IMPORTANT Do not connect the USB cable until cable." , "Connect the USB Setup flow This side explains the setup procedure for use without connecting to a computer.
PAGE 2
Check the contents. • Ink tanks BCI-24 Black BCI-24 Color • Print head • MP370 • MP360 • Power cord • Set-Up Sheet • User's Guide • Setup CD-ROM The Setup CD-ROM contains the MP Drivers, as well as the electronic manuals Software Guide and Photo Application Guide. Please read these guides. NOTE • In this sheet, illustrations of MP370 are shown. • A printer cable is not included. You must purchase a USB cable (less than 16 3/8 ft./5 m) to connect your machine to a computer. Connect the power cord.
PAGE 3
Install the print head. 1 Lift the scan unit until it locks into place. • If a protective sheet is on the inner side of the scan unit, remove the protective sheet. Lift the scan unit. Click If the paper output tray does not open, press the Open button to open the paper output tray. NOTE • If you open the scan unit while the machine is turned ON, the paper output tray will open. 2 Open the inner cover. 3 Raise the lock lever. w The print head holder moves to the center. Touch only here! Install here.
PAGE 4
Install the ink tanks. 1 Prepare the ink tanks. 2 Insert the ink tanks. Click Black Remove the protective cap and dispose of it. Do not touch! Insert the black ink Push it in until it tank into the right slot. locks into place. Insert the color ink tank into the left slot. NOTE 3 Close the inner cover q and the scan unit w. Click Incorrectly installed w Lower it into place. Correctly installed q Swing it upward into place. Load the print media. 1 Open the multi-purpose tray.
PAGE 5
Align the print head from the operation panel. Be sure to align the position of the print head to ensure quality printing. 1 Print the print head position pattern. q This message appears. w Press [Set]. If this message does not appear after closing the scan unit, see page 86 of the User's Guide. e The machine prints a print head position pattern. 2 Enter checkmarks in the printed patterns.
PAGE 6
Install the MP Drivers. The MP Drivers must be installed on the hard disk of your computer in order to print from or scan images to the computer. In addition to installing the MP Drivers, install the MP Toolbox. Use the MP Toolbox to attach scanned images to e-mail and store them. IMPORTANT • For detailed system requirements, see page 64 of the User's Guide. • When installing the software in Windows 2000, you must have Service Pack 1 or later version installed.
PAGE 7
1 Install the MP Drivers. (Use when printing from PC applications or scanning images.) Follow the on-screen instructions to install the software. Click When the InstallShield Wizard Complete window appears, click [Finish]. If you are prompted to restart your computer after the installation, restart your computer. When restarting your computer is not necessary: Click When restarting your computer is necessary: Select [Yes, I want to restart my computer now.]. 2 Install the MP Toolbox.
PAGE 8
Connect the USB cable. Connect one end of the USB cable to the computer, the other (square shaped plug) to the machine. Make sure both your machine and computer are turned ON. When connecting the USB cable, the computer will automatically set necessary information. Please wait shortly. Click [OK] if you are prompted to restart your computer. In Windows 2000, the machine may not be set as [Set As Default Printer]. For details, see the Software Guide. Install the utility software.