Service manual

Chapter 14
14-9
14.4.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)>
0011-4178
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Adjust the position at which horizontal scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the top margin of the image
becomes.
14.4.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)>
0011-4179
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Adjust the position at which horizontal scanning of a document being copied ends (when scanning on a document fed from ADF). The larger the adjustment value,
the narrower the bottom margin of the image becomes.
14.4.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)>
0011-4180
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Adjust the position at which horizontal scanning of a FAX document scanned in superfine mode ends. The larger the adjustment value, the narrower the bottom
margin of the image becomes.
14.4.13 <045: Horizontal scan end position correction (fine:scanning on ADF)>
0011-4181
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Adjust the position at which horizontal scanning of a FAX document scanned in fine mode ends. The larger the adjustment value, the narrower the bottom margin
of the image becomes.
14.4.14 <046: Horizontal scan end position correction (standard:scanning on ADF)>
0011-4182
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Adjust the position at which horizontal scanning of a FAX document set to the standard scan resolution ends. The larger the adjustment value, the narrower the
bottom margin of the image becomes.
14.4.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)>
0011-4183
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Correct the magnification of vertical scanning of a document fed from the ADF. The larger the adjustment value, the more the image stretches in the vertical scan-
ning direction.
14.4.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)>
0011-4184
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Correct the magnification of horizontal scanning of a document fed from the ADF. The smaller the adjustment value, the more the image ruduces in the horizontal
scanning direction.
This menu is used to adjust the ADF feed motor speed. If you changed the adjustment value in this mode, the adjustment value selected for SCAN NUMERIC>54
must also be incremented/decremented by the same amount.
Do not change the adjustment value extremely.
14.4.17 <054: Pickup motor speed correction (when the ADF is used) >
0011-4185
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
This menu is used to adjust the ADF pickup motor speed. If you have adjusted the ADF feed motor speed by selecting SCAN NUMERIC>48, the ADF pickup
motor speed must also be incremented/decremented by the same amount.
Do not change the adjustment value extremely.
14.4.18 <193: ADF special standard-sized paper: LGL misidentification-ready>
0011-4208
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LEGAL").
0: LEGAL
1: FOOLSCAP
2: M_OFFICIO
3: A_FOOLSCAP
4: FOLIO
5: G_LEGAL
6: A_OFFICIO
7: B_OFFICIO
14.4.19 <194: ADF special standard-sized paper: LTR misidentification-ready>
0011-4209
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").
0: LTR
1: G_LTR
2: A_LTR
14.4.20 <195: ADF special standard-sized paper: LTR_R misidentification-ready>
0011-4210
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTRR").
0: LTR_R
Download Free Service Manual And Resetter Printer at http://printer1.blogspot.com