FAXPHONE L80 Set-Up Instructions

ManualsBrandsCanon ManualsFax MachineFAXPHONE L80

Set-Up Instructions

Thank you for purchasing the Canon FAXPHONE L80.

To get your machine ready for use, please follow the instructions in this document before

referring to any other documentation.

Unpack the machine and its components.

Check that you have the following:

NOTE

•You need a USB cable (less than 16.4 ft./5 m) to connect your machine to a computer.

•To lift the machine, hold it firmly and level as illustrated.

●

Machine

●

FX-3 S Cartridge

●

Support trays (2)

●

Multi-purpose

tray

●

Multi-purpose tray

cover

●

Document support

●

Handset

●

Handset cradle

●

Plugs with

pins (2)

●

Paper loading warning label

●

Power cord

●

Telephone line cord

●

Documentation

Set-Up Instructions

Basic Guide

Warranty

Registration card (for USA only)

●

FAXPHONE L80 Software CD-ROM

●

Destination labels

Summary of content (8 pages)

PAGE 1
Set-Up Instructions Thank you for purchasing the Canon FAXPHONE L80. To get your machine ready for use, please follow the instructions in this document before referring to any other documentation. Unpack the machine and its components.
PAGE 2
Remove the shipping materials from the machine. 1 Place the machine on a flat surface. 2 Remove all shipping tapes from the exterior of the machine. 3 Gently open the operation panel ➊ (it only opens partially) and remove the protective sheet ➋ from the ADF. 4 Close the operation panel by pressing at the center until it locks into place. NOTE Ë • Do not remove the USB label on the back of the machine at this stage. USB label Assemble the machine. 1 Attach the paper loading warning label.
PAGE 3
Load paper. 1 Insert a stack of paper into the multi-purpose tray ➊ (print side facing you and top edge first), then adjust the paper width guides to the width of the paper ➋. 2 Attach the multi-purpose tray cover to prevent dust accumulating inside the machine. Ë Multi-purpose tray cover Ë Paper width guide Attach the handset cradle to the machine. 1 Insert the plugs with pins into the holes on the handset cradle. Plug with pin NOTE • Do not push the pins all the way into the plugs at this stage.
PAGE 4
Connect the handset and telephone line cord. Connect external devices as follows: = Telephone line jack = External device jack = Handset jack • Telephone or answering machine Telephone or answering machine Telephone line Telephone line cord Connect the supplied cord to the L jack. Then connect the other end to the telephone line jack on your wall. External device (optional) Connect the cord of an extension telephone, answering machine or data modem to the t jack.
PAGE 5
Install the FX-3 S Cartridge. 1 Lift the latch and open the front cover. 2 Remove the FX-3 S Cartridge from its protective bag. 3 Gently rock the cartridge from side to side a few times to distribute the toner evenly inside it. •Print quality may be poor if the toner is unequally distributed. NOTE • Do not open the drum protective shutter on the cartridge. 4 Place and hold the cartridge on a flat, clean surface, then gently pull the plastic tab straight out to remove the plastic seal.
PAGE 6
Set the fax receive mode. 1 Press Function ➊. Clear 01 02 03 04 05 06 07 08 Set 2 Press Receive Mode ➋. 3 Press or ➌ until the mode you want appears in the LCD: Data Delayed Registration Transmission 10 09 Polling 13 ex.
PAGE 7
Install the Printer Driver. (Windows 98/Me/2000/XP) IMPORTANT • DO NOT connect the USB cable before installing the software. NOTE • When installing the software in Windows XP or Windows 2000, log onto the system as a member of the Administrator group. • If the Found New Hardware Wizard appears, click Cancel, and follow this procedure. 1 Insert the CD-ROM into your CD-ROM drive. 2 If AutoRun is enabled, the installation starts automatically. NOTE • If installation does not start automatically, choose Run.
PAGE 8
6 When the system displays messages indicating that the driver for your printer is being installed, proceed as follows: For Windows 98/Me: Wait for the system to complete the installation of the printer driver. For Windows 2000: When the Found New Hardware Wizard appears during the setup, choose the following: • Search for a suitable driver for the printer. (Do not display a list of drivers.) • Search only on the installation disk. (Click CD-ROM drives only, and clear the other options.