C INSTRUCTION MANUAL E Y P O E INSTRUCTION MANUAL
Thank you for purchasing a Canon product. The EOS 50D is a high-performance, digital SLR camera featuring a fine-detail CMOS sensor with 15.10 effective megapixels, DIGIC 4, high-precision and high-speed 9-point AF (all cross-type points), highspeed 6.3 fps continuous shooting, and Live View shooting. The camera is highly responsive to any shooting situation at anytime, provides many features for demanding shoots, and expands shooting possibilities with system accessories.
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Camera Battery Pack BP-511A (with protective cover) Battery Charger CG-580/CB-5L* (with eyecup and body cap) Wide Strap EW-EOS50D EOS DIGITAL Solution Disk (Software) Y P O Interface Cable IFC-200U C Video Cable Software Instruction Manual (1) Instruction Manual (this booklet) (2) Pocket Guide Quick start guide to shooting.
Conventions Used in this Manual Icons in this Manual <6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. <9> : Indicates the Multi-controller. <0> : Indicates the setting button. 0, 9, 8 : Indicates that the respective function remains active for 4 sec., 6 sec., or 16 sec. respectively after you let go of the button. * In this manual, the icons and markings indicating the camera’s buttons, dials, and settings correspond to the icons and markings on the camera and on the LCD monitor.
Chapters For first-time users, chapters 1 and 2 explain the camera’s basic operations and shooting procedures. Introduction 2 Camera basics. 1 2 3 4 5 6 7 8 9 10 11 Getting Started 23 Basic Shooting Fully automatic shooting for different subjects. Image Settings Y P O Setting the AF and Drive Modes Advanced Operations C Shooting features for specific types of subjects. Live View Shooting Shoot while viewing the LCD monitor.
Contents Introduction Item Check List.................................................................................................. 3 Conventions Used in this Manual ...................................................................... 4 Chapters ............................................................................................................ 5 Index to Features ............................................................................................ 10 Handling Precautions ..............
Contents 3 Image Settings 59 Setting the Image-recording Quality.................................................................60 i: Setting the ISO Speed..............................................................................63 A Selecting a Picture Style ..........................................................................65 A Customizing a Picture Style .....................................................................67 A Registering a Picture Style...................................
Contents D Using the Built-in Flash.............................................................................. 107 Flash Control ................................................................................................. 111 External Speedlites ....................................................................................... 113 6 Live View Shooting 7 Image Playback 115 A Preparing for Live View Shooting............................................................ 116 Shooting .........
Contents 9 Printing Images and Transferring Images to a Computer 153 Preparing to Print ...........................................................................................154 w Printing.....................................................................................................156 Trimming the Image ....................................................................................161 Digital Print Order Format (DPOF).................................................................
Index to Features Power Image improvement features Battery • Charging • Battery check Î p.24 Î p.28 Power outlet Î p.190 Auto power off Î p.44 Lens Attaching/Detaching Î p.31 Zoom Î p.32 Image Stabilizer Î p.33 Basic Settings (Menu Functions) • Lens peripheral illumination correction Î p.76 • Auto Lighting Optimizer Î p.177 • Noise reduction for long exposures Î p.176 • Noise reduction for high ISO Î p.176 • Highlight tone priority Î p.177 White balance White balance selection Î p.
Index to Features Shooting Image playback Creative Auto Î p.57 Image review time Î p.145 Quick Control screen Î p.38 Single image playback Î p.132 Self-timer Î p.90 Program AE Î p.92 • Shooting information display Î p.133 Shutter-priority AE Î p.94 Index display Î p.135 Aperture-priority AE Î p.96 Manual exposure Î p.98 Image browsing (Jump display) Î p.136 Bulb Î p.104 Magnified view Î p.137 Mirror lockup Î p.106 Manual image rotate Î p.138 Auto image rotate Î p.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth. Never leave the camera near anything having a strong magnetic field such as a magnet or electric motor.
Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there might be a few dead pixels among the remaining 0.01% or less pixels. Dead pixels displaying only black or red, etc., are not a malfunction. They do not affect the images recorded. If the LCD monitor is left on for a prolonged period, screen burn-in may occur where you see remnants of what was displayed.
Quick Start Guide Insert the battery. (p.26) 1 2 3 To recharge the battery, see page 24. For EF-EF-S S レンズ lens For EF lens Attach the lens. (p.31) When attaching an EF-S lens, align it with the white index on the camera. For other lenses, align it with the red index. Y P O Set the lens focus mode switch to . (p.31) C Open the slot cover and insert a card. (p.29) 4 Face the label side toward you and insert the end with the small holes into the camera. 5 14 Set the power switch to <1>.
Quick Start Guide Set the Mode Dial to <1> (Full Auto). (p.48) 6 All the necessary camera settings will be set automatically. Focus the subject. (p.35) 7 8 9 Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus the subject. If necessary, the built-in flash will popup automatically. C Y P O Take the picture. (p.35) Press the shutter button completely to take the picture. Review the picture. (p.
Nomenclature For detailed information, reference page numbers are provided in parentheses (p.**). Metering mode selection/White balance selection button (p.100/71) LCD panel illumination button (p.104) LCD panel (p.18) AF mode selection/Drive mode selection button (p.84/89) EF lens mount index (p.31) Built-in flash/AF-assist beam (p.107/87) ISO speed setting/ Flash exposure compensation button (p.63/109) EF-S lens mount index (p.31) Flash-sync contacts <6> Main Dial (p.
Nomenclature Focal plane mark AF start button (p.35,84,118) <9> Multi-controller (p.36) AE lock/ FE lock button/Index/ Reduce button (p.103/110/135/137,161) Dioptric adjustment knob (p.34) Eyecup (p.97) Viewfinder eyepiece Live View shooting/Print/Share button (p.117/159,168) AF point selection/ Magnify button (p.86/137,161) Menu button (p.40) Strap mount (p.23) LCD monitor (p.40, 145) Info/ Trimming orientation button (p.120,132,188/ 161) Playback button (p.
Nomenclature LCD Panel Shutter speed Busy (buSY) AF point selection ([ - -- --- -- - ]) Card full warning (FuLL CF) Built-in flash recycling (buSY) Card error warning (Err CF) No card warning (no CF) Image-recording quality (p.60) 37 38 47 48 67 68 1 D Error code (Err) Large/Fine Large/Normal Medium/Fine Medium/Normal Small/Fine Small/Normal RAW Small RAW White balance (p.
Nomenclature Viewfinder Information AF points (Superimposed display) Focusing screen Spot metering circle ISO speed AE lock/ AEB in-progress Flash-ready Improper FE lock warning C Y P O White balance correction Focus confirmation light Max.
Nomenclature Mode Dial The Mode Dial has the Basic Zone modes and Creative Zone modes. Camera User Settings Most camera settings can be registered under w or x (p.186). Creative Zone These modes give you more control over the result. d : Program AE (p.92) s : Shutter-priority AE (p.94) f : Aperture-priority AE (p.96) Y P O a : Manual exposure (p.98) 8 : Automatic depth-of-field AE (p.99) C Basic Zone All you do is press the shutter button. Fully automatic shooting for specific kinds of subjects.
Nomenclature Nomenclature for Kit Lenses EF-S18-200mm f/3.5-5.6 IS and EF-S18-55mm f/3.5-5.6 IS EF-S18-135mm f/3.5-5.6 IS Focus mode switch (p.31) Focusing ring (p.88,127) Zoom ring (p.32) Zoom position index (p.32) Hood mount (p.209, 210) Filter thread (front of lens) (p.209, 210) Image Stabilizer switch (p.33) Lens mount index (p.31) C Y P O Contacts (p.13) EF-S17-85mm f/4-5.6 IS USM and EF28-135mm f/3.5-5.6 IS USM Focus mode switch (p.31) Hood mount (p.209, 210) Zoom position index (p.
Nomenclature Battery Charger CG-580 Charger for Battery Pack BP-511A (p.24). Power plug Battery pack slot Charge lamp This power unit is intended to be correctly orientated in a vertical or floor mount position. Y P O IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet.
1 Getting Started Y P O This chapter explains preparatory steps and basic camera operations. C Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap (p.105).
Recharging the Battery 1 Remove the protective cover. When you remove the battery from the camera, be sure to reattach the cover to protect it against short circuiting. the battery. 2 Attach Align the battery’s front edge with the battery charger’s index line. While pressing down the battery, slide it in the direction of the arrow. To detach the battery, follow the above procedure in reverse. Battery pack slot index CG-580 the battery.
Recharging the Battery Tips for Using the Battery and Charger Recharge the battery on the day before or on the day it is to be used. Even during non-use or storage, a charged battery will gradually discharge and lose its power. After recharging the battery, detach it and unplug the power cord or prongs from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Installing the Battery Load a fully charged Battery Pack BP-511A into the camera. 1 Open the battery compartment cover. Slide the lever as shown by the arrow and open the cover. the battery. 2 Insert Insert the end with the battery contacts. Insert the battery until it locks in place. Y P O the cover. 3 Close Press the cover until it snaps shut. C Battery Pack BP-514, BP-511, or BP-512 can also be used. Removing the Battery Open the cover and remove the battery.
Turning on the Power <2> : The camera is turned off and does not operate. Set to this position when not using the camera. <1> : The camera turns on. : The camera and <5> operate (p.37). About the Automatic Self-Cleaning Sensor Whenever you set the power switch to <1/J> or <2>, the sensor cleaning will be executed automatically. During the sensor cleaning, the LCD monitor will display . Even during the sensor cleaning, you can still shoot by pressing the shutter button halfway (p.
Turning on the Power Checking the Battery Level When the power switch is set to <1> or , the battery level will be indicated in one of four levels: z : Battery level is OK. x : Battery level is slightly down, but adequate power remains. b : Battery will be exhausted soon. n : Battery must be recharged. Battery Life Temperature [Approx.
Installing and Removing the CF Card Although the thickness is different between the two types of CF cards, either one can be inserted into the camera. Also, Ultra DMA (UDMA) cards and hard disk-type cards can be used. Installing the Card 1 Label side Card ejection button Open the cover. Slide the cover as shown by the arrow to open it. the card. 2 Insert As shown in the illustration, face the label side toward you and insert the end with the small holes into the camera.
Installing and Removing the CF Card Removing the Card 1 Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. Access lamp the card. 2 Remove Press the card ejection button. X The card will come out. Close the cover. Card ejection button Y P O The access lamp lights or blinks while the picture is taken, when data is being transferred to the card and when data is being recorded, read, or erased on the card.
Attaching and Detaching a Lens Attaching a Lens 1 EF-S lens mount index Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrow. the lens. 2 Attach Align the EF-S lens with the camera’s white EF-S lens mount index and turn the lens as shown by the arrow until it clicks in place. When attaching a lens other than an EF-S lens, align the lens with the red EF lens mount index. EF lens mount index Y P O the lens, set the focus mode 3 On switch to (autofocus).
Attaching and Detaching a Lens About Zooming To zoom, turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus slightly. Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrow. Y P O Turn the lens until it stops, then detach it. Attach the dust cap to the detached lens. C To owners of the EF-S18-200mm f/3.5-5.
About the Lens Image Stabilizer The procedure explained here is based on the EF-S17-85mm f/4-5.6 IS USM lens as an example. * IS stands for Image Stabilizer. 1 Set the IS switch to <1>. Set the camera’s power switch to <1>. the shutter button halfway. 2 Press X The Image Stabilizer will operate. the picture. 3 TakeWhen the picture looks steady in the Y P O viewfinder, press the shutter button completely to take the picture. C The Image Stabilizer is not effective for moving subjects.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the nine AF points in the viewfinder look sharp. If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lens E (10 types, sold separately) is recommended. Holding the Camera Y P O To obtain sharp images, hold the camera still to minimize camera shake. C Horizontal shooting Vertical shooting 1.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and automatic exposure metering that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed on the LCD panel and in the viewfinder (0). Pressing completely This releases the shutter and takes the picture.
Basic Operation <6> Using the Main Dial for Selecting (1) After pressing a button, turn the <6> dial. When you press a button, its function remains selected for 6 seconds (9). During this time, you can turn the <6> dial to set the desired setting. When the function turns off or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select or set the metering mode, AF mode, ISO speed, AF point, etc. Y P O (2) Turn the <6> dial only.
Basic Operation <5> Using the Quick Control Dial for Selecting Before using the <5> dial, set the power switch to . (1) After pressing a button, turn the <5> dial. When you press a button, its function remains selected for 6 seconds (9). During this time, you can turn the <5> dial to set the desired setting. When the function turns off or if you press the shutter button halfway, the camera will be ready to shoot.
Using the Quick Control Screen The shooting settings are displayed on the LCD monitor where you can quickly select and set the functions. This is called the Quick Control screen. 1 Display the Quick Control screen. Press <9> straight down. X The Quick Control screen will appear (10 sec.). the desired setting. 2 SetUse <9> to select the function. Basic Zone modes In the Basic Zone modes, you can select certain drive modes (p.89) and the image-recording quality (p.60).
Using the Quick Control Screen Quick Control Screen Nomenclature Aperture (p.96) Shutter speed (p.94) ISO speed (p.63) Exposure compensation/ AEB setting (p.102) Highlight tone priority (p.177) Shooting mode (p.20) Metering mode (p.100) Flash exposure compensation (p.109) Drive mode (p.89) Image-recording quality (p.60) White balance (p.71) AF point (p.86) Picture Style (p.65) Function Setting Display C Ð <0> AF mode (p.84) Y P O On the Quick Control screen, select the function and press <0>.
Menu Operations By setting various functions with the menus, you can set the imagerecording quality, date/time, etc. While looking at the LCD monitor, you use the button on the camera back and the <6> <5> dials. button LCD monitor <6> Main Dial <5> Quick Control Dial <0> button Basic Zone Mode Menu Screen C Y P O * The [2/8/9] tabs are not displayed in the Full Auto and Basic Zone modes. When a Basic Zone mode is set, there are menu items which are not displayed.
Menu Operations Menu Setting Procedure 1 Display the menu. Press the button to display the menu. a tab. 2 Select Turn the <6> dial to select a tab. the desired item. 3 Select Turn the <5> dial to select the item, then press <0>. Y P O the setting. 4 Select Turn the <5> dial to select the C desired setting. Some menu items will indicate the current setting in blue. the desired setting. 5 SetPress <0> to set it. the menu. 6 ExitPress the button to exit the menu and return to camera shooting.
Before You Start 3 Setting the Interface Language 1 Select [Language]. Under the [6] tab, select [Language] (the third item from the top), then press <0>. the desired language. 2 SetTurn the <5> dial to select the language, then press <0>. X The language will change. 3 Setting the Date and Time Y P O Check if the camera’s date and time are set correctly. If necessary, set the correct date and time. 1 Select [Date/Time]. C 2 Under the [6] tab, select [Date/ Time], then press <0>.
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or personal computer, format the card with the camera. When the card is formatted, all images and data in the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images to a personal computer, etc., before formatting the card. 1 Select [Format]. Under the [5] tab, select [Format], then press <0>. Y P O [OK].
Before You Start 3 Set the Power-off Time/Auto Power Off You can change the auto power-off time for the camera to turn off automatically after a certain period of non-operation. If you do not want the camera to turn off automatically, set this to [Off]. After the power turns off, you can turn on the camera again by pressing the shutter button or other button. 1 Select [Auto power off]. Under the [5] tab, select [Auto power off], then press <0>. the desired time.
Before You Start 3 Reverting the Camera to the Default SettingsN The camera’s shooting settings and menu settings can be reverted to the default. 1 Select [Clear settings]. Under the [7] tab, select [Clear settings], then press <0>. [Clear all camera settings]. 2 Select Turn the <5> dial to select [Clear all camera settings], then press <0>. [OK]. 3 Select Turn the <5> dial to select [OK], Y P O then press <0>.
Before You Start Camera Settings Camera Settings Auto power off 1 min. Beep On Image jump w/6 Auto rotate Shoot w/o card On LCD brightness Review time 2 sec.
2 Basic Shooting Y P O This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. With the Basic Zone modes, all you do is point and shoot and the camera sets everything automatically (p.196). Also, to prevent botched pictures due to mistaken operations, shooting settings cannot be changed in the Basic Zone modes.
1 Fully Automatic Shooting 1 AF point Set the Mode Dial to <1>. any AF point over the 2 Aim subject. All the AF points will operate, and focus will generally be achieved at the AF point covering the closest object. Aiming the center AF point over the subject will make focusing easier. the subject. 3 Focus Press the shutter button halfway, and Y P O the lens focusing ring will rotate to focus. X The AF point which achieves focus will briefly flash in red.
1 Fully Automatic Shooting FAQ The focus confirmation light blinks and focus is not achieved. Aim the AF point over an area having good contrast between light and dark, then press the shutter button halfway (p.88). If you are too close to the subject, move away and try again. Sometimes multiple AF points flash simultaneously. This indicates that focus has been achieved at all those AF points. As long as the AF point covering the desired subject flashes, you can take the picture.
1 Full Auto Techniques Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the <1> (Full Auto) mode, while you press the shutter button halfway to focus a still subject, the focus will be locked. You can then recompose the shot and press the shutter button completely to take the picture. This is called “focus lock”. Focus lock is also possible in other Basic Zone modes (except <5> Sports).
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes flesh tones and the hair look softer than with the <1> (Full Auto) mode. Shooting Tips C Y P O The farther the distance between the subject and background, the better. The further the distance between the subject and background, the more blurred the background will look. The subject will also stand out better in front of a plain, dark background. Use a telephoto lens.
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery, night scenes, or to have everything in focus from near to far. The greens and blues also become more vivid and sharper than with <1> (Full Auto). Shooting Tips C Y P O With a zoom lens, use the wide-angle end. When using the wide-angle end of a zoom lens, objects near and far will be in focus better than at the telephoto end. It also adds breadth to landscapes. Shooting night scenes.
4 Shooting Close-ups When you want to photograph flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips C Y P O Use a simple background. A simple background makes the flower, etc., stand out better. Move to the subject as close as possible. Check the lens for its minimum focusing distance. Some lenses have indications such as <40.28m/0.9ft>.
5 Shooting Moving Subjects To photograph a moving subject, whether it is a child running or a moving vehicle, use the <5> (Sports) mode. Shooting Tips Y P O Use a telephoto lens. Using a telephoto lens is recommended so you can shoot from afar. C Use the center AF point to focus. Aim the center AF point over the subject, then press the shutter button halfway to auto focus. During autofocusing, the beeper will continue beeping softly.
6 Shooting Portraits at Night To shoot someone at night and obtain a natural-looking exposure in the background, use the <6> (Night Portrait) mode. Shooting Tips Y P O Use a wide-angle lens and a tripod. When using a zoom lens, use the wide-angle end to obtain a wide night view. Also, use a tripod to prevent camera shake. C Keep the person within 5 meters/16.4 feet from the camera. Under low light, the built-in flash will fire automatically to obtain a good exposure of the person.
7 Disabling Flash In places where flash photography is prohibited, use the <7> (Flash Off) mode. This mode is also effective for candlelight scenes when you want to capture the ambient light. Shooting Tips C Y P O If the numeric display in the viewfinder blinks, take care to prevent camera shake. Under low light when camera shake is prone to occur, the viewfinder’s shutter speed display will blink. Hold the camera steady or use a tripod.
C Creative Auto Shooting The (Creative Auto) mode enables you to easily change the picture’s brightness, etc. The default settings are the same as the <1> (Full Auto) mode. * CA stands for Creative Auto. 1 Set the Mode Dial to . X The Creative Auto screen appears on the LCD monitor. <9> straight down. 2 Press X You can use <9> to select a function. Functions (1) to (6) shown on the next page can be selected. Y P O the desired setting. 3 SetUse <9> to select the function.
C Creative Auto Shooting Shutter speed and aperture (1) (2) (3) (4) (6) (5) Possible shots Battery check Maximum burst (1) Flash firing (Auto firing), (Flash on), or (Flash off, with AF-assist beam enabled) can be selected. If you set , see “Disabling Flash” on page 56. Y P O (2) Blurring/sharpening the background If you move the index mark toward the left, the background will look more blurred. If you move it toward the right, the background will look more in focus.
3 Image Settings Y P O This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Styles, white balance, color space, etc. C In the Basic Zone modes, you can only set the imagerecording quality and lens peripheral illumination correction, create and select folders, and set the file numbering as explained in this chapter. The M icon on the right of the page title indicates that the respective feature is available only in Creative Zone modes (d, s, f, a, 8).
3 Setting the Image-recording Quality You can select the pixel count and the image quality. The following JPEG quality settings can be set: 73, 83, 74, 84, 76, 86. RAW images captured as 1, D1, or D2 must be processed with the provided software (p.62). 1 Select [Quality]. Under the [1] tab, select [Quality], then press <0>. X The [Quality] screen will appear. the image-recording quality. 2 Select To select a RAW setting, turn the <6> dial. To select a JPEG setting, turn the <5> dial.
3 Setting the Image-recording Quality Guide to Image-recording Quality Settings (Approx.) Pixels Printing Size Approx. 15.1 megapixels (15M) A3 or larger Approx. 8.0 megapixels (8M) A3 - A4 Approx. 3.7 megapixels (3.7M) A4 or smaller 1 Approx. 15.1 megapixels (15M) D1 D2 Quality 73 83 JPEG setting 74 84 5.0 370 60 (90) 2.5 740 150 (740) 3.0 620 110 (620) 1.6 1190 390 (1190) 1.7 1090 330 (1090) 0.9 2040 1050 (2040) A3 or larger 20.2 91 16 (16) Approx. 7.1 megapixels (7.
3 Setting the Image-recording Quality About RAW The RAW image is the data output by the image sensor and converted to digital data which is recorded on the card as is. You can select it from among 1, D1, or D2. “RAW” written in the text will refer to all three RAW settings: 1, D1, and D2. With RAW images, you can use the provided software to make various adjustments as needed. From the RAW image, the software can develop and produce the adjusted image in the desired type such as JPEG or TIFF. About [8C.
3 Setting the Image-recording Quality The maximum burst is displayed even when a card is not in the camera. Make sure that a card is loaded before taking a picture. The maximum burst for is displayed regardless of the drive mode setting. If [8C.Fn II -2: High ISO speed noise reduction] is set to [2: Strong], the maximum burst will be reduced (p.176). If the viewfinder displays “99” for the maximum burst, it means the maximum burst is 99 or higher.
i: Setting the ISO SpeedN ISO Speed Guide ISO Speed Shooting Situation (No flash) 100 - 200 Sunny outdoors 400 - 800 Overcast skies, evening 1600 - 3200, H1, H2 Dark indoors or night Flash Range The higher the ISO speed, the farther the flash range will be (p.108). If [8C.Fn II -3: Highlight tone priority] is set to [1: Enable], the settable ISO speed range will be ISO 200 - 3200 (p.177). Using a high ISO speed or shooting in high-temperature conditions may result in more grainy images.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain the image effects matching your photographic expression or the subject. In the Basic Zone modes (except for C), you cannot select the Picture Style. 1 Press the button. When the camera is ready to shoot, press the button. X The Picture Style screen will appear. a Picture Style. 2 Select Turn the <6> or <5> dial to select a Picture Style, then press <0>.
A Selecting a Picture StyleN S Neutral This Picture Style is for users who prefer to process images with their personal computer. For natural colors and subdued images. U Faithful This Picture Style is for users who prefer to process images with their personal computer. When the subject is captured under a color temperature of 5200K, the color is adjusted colorimetrically to match the subject’s color. The image is dull and subdued. V Monochrome (C: Monochrome image) For black-and-white images.
A Customizing a Picture StyleN You can customize a Picture Style by adjusting individual parameters like [Sharpness] and [Contrast]. To see the resulting effects, take test shots. To customize [Monochrome], see the next page. 1 Press the button. a Picture Style. 2 Select Turn the <6> or <5> dial to select a Picture Style, then press the button. a parameter. 3 Select Turn the <5> dial to select a parameter, then press <0>. Y P C4 O Set the parameter.
A Customizing a Picture StyleN By selecting [Default set.] in step 3, you can revert the respective Picture Style to its default parameter settings. To shoot with the Picture Style you modified, follow step 2 on the preceding page to select the modified Picture Style and then shoot. Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding page.
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create Picture Styles whose parameter settings such as for sharpness and contrast are different. You can also adjust the parameters of a Picture Style which has been registered to the camera with the provided software. 1 Press the button. [User Def.].
A Registering a Picture StyleN the parameter. 6 SetTurn the <5> dial to adjust the parameter as desired, then press <0>. For details, see “Customizing the Picture Style” on pages 67-68. Press the button to register the new Picture Style. The Picture Style selection screen will then reappear. X The base Picture Style will be indicated on the right of [User Def. *]. C Y P O If a Picture Style has already been registered under [User Def.
B: Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the (Auto) setting will obtain the correct white balance. If naturallooking colors cannot be obtained with , you can select the white balance for each light source or set it manually by shooting a white object. In the Basic Zone modes, will be set automatically. 1 Press the button. (9) the white balance. 2 Select While looking at the LCD panel, turn the <5> dial.
B: Setting the White BalanceN O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Do this procedure under the actual light source to be used. 1 Photograph a white object. The plain, white object should fill the spot metering circle. Focus manually and set the standard exposure for the white object. You can set any white balance. Spot metering circle Y P O [Custom WB].
B: Setting the White BalanceN If the exposure obtained in step 1 is way off, a correct white balance might not be obtained. If the image was captured while the Picture Style was set to [Monochrome] (p.66), it cannot be selected in step 3. Instead of a white object, an 18% gray card (commercially available) can produce a more accurate white balance. The personal white balance registered with the provided software will be registered under .
3 White Balance CorrectionN You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This is for advanced users who are familiar with using color temperature conversion or color compensating filters. White Balance Correction 1 Select [WB SHIFT/BKT]. Under the [2] tab, select [WB SHIFT/BKT], then press <0>.
3 White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images having a different color tone can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing (WB-BKT). White balance bracketing is possible up to ±3 levels in single-level increments. Set the white balance bracketing amount.
3 Lens Peripheral Illumination Correction Due to the lens characteristics, the four corners of the picture might look darker. This is called lens light fall-off or drops in peripheral illumination. This can be corrected. For JPEG images, lens light fall-off is corrected when the image is captured. For RAW images, it can be corrected with Digital Photo Professional (provided software). 1 Select [Peripheral illumin. correct.]. Under the [1] tab, select [Peripheral illumin. correct.], then press <0>.
3 Lens Peripheral Illumination Correction About the Lens Correction Data The camera already contains lens peripheral light correction data for about 20 lenses. In step 2, if you select [Enable], the peripheral light correction will be applied automatically for any lens whose correction data has been registered in the camera. With the EOS Utility (provided software), you can check which lenses have their correction data registered in the camera.
3 Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This is optional since a folder will be created automatically for saving captured images. Create a Folder 1 Select [Select folder]. Under the [5] tab, select [Select folder], then press <0>. [Create folder]. 2 Select Turn the <5> dial to select [Create Y P O folder], then press <0>. C a folder. 3 Create Turn the <5> dial to select [OK], then press <0>.
3 Creating and Selecting a Folder Selecting a Folder Lowest file number Quantity of images in folder With the Select folder screen displayed, turn the <5> dial to select the desired folder, then press <0>. X The folder where the captured images will be saved will be selected. Subsequent captured images will be recorded into the selected folder.
3 File Numbering Methods The file number is like the frame number on a roll of film. The captured images are assigned a sequential file number from 0001 to 9999 and saved in one folder. You can change how the file number is assigned. The file number will appear on a personal computer in this format: IMG_0001.JPG. 1 Select [File numbering]. Under the [5] tab, select [File numbering], then press <0>. the file numbering method. 2 Select Turn the <5> dial to select the desired method, then press <0>.
3 File Numbering Methods Auto Reset The file numbering restarts from 0001 each time the card is replaced or a new folder is created. Whenever the card is replaced or a new folder created, the file numbering starts from 0001. This is convenient if you want to organize images according to cards or folders.
3 Setting the Color SpaceN The color space refers to the range of reproducible colors. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. In the Basic Zone modes, sRGB is set automatically. 1 Select [Color space]. Under the [2] tab, select [Color space], then press <0>. the desired color space. 2 SetSelect [sRGB] or [Adobe RGB], then press <0>.
4 Setting the AF and Drive Modes Y P O The viewfinder has 9 AF points. By selecting a suitable AF point, you can shoot with autofocus while framing the subject as desired. C You can also select the AF mode and drive mode best matching the shooting conditions and subject. The M icon on the right of the page title indicates that the respective feature is available only in the Creative Zone modes (d, s, f, a, 8).
f: Selecting the AF ModeN Select the AF mode suiting the shooting conditions or subject. In the Basic Zone modes, the optimum AF mode is set automatically. 1 On the lens, set the focus mode switch to . the Mode Dial to a Creative 2 Set Zone mode. 3 Press the button. (9) Y P O the AF mode. 4 Select While looking at the LCD panel, turn the <6> dial. C X: One-Shot AF 9: AI Focus AF Z: AI Servo AF One-Shot AF for Still Subjects Suited for still subjects.
f: Selecting the AF ModeN If focus cannot be achieved, the focus confirmation light in the viewfinder will blink. If this occurs, a picture cannot be taken even if the shutter button is pressed completely. Recompose the picture and try to focus again. Or see “When Autofocus Fails” (p.88). If the [1 Beep] menu is set to [Off], the beeper will not sound when focus is achieved. AI Servo AF for Moving Subjects This AF mode is for moving subjects when the focusing distance keeps changing.
S Selecting the AF PointN Select one of the nine AF points to autofocus. In the Basic Zone and <8> modes, automatic AF point selection will take effect automatically. You cannot select the AF point. 1 Press the button. (9) X The selected AF point will be displayed in the viewfinder and on the LCD panel. When all AF points light up, automatic AF point selection will be set. the AF point. 2 Select To select an AF point, you can either turn the <6> or <5> dial or use <9>.
S Selecting the AF PointN When looking at the LCD panel to select the AF point, note the following: Automatic selection , center , right , top If focus cannot be achieved with the external, EOS-dedicated Speedlite’s AF-assist beam, select the center AF point. AF-Assist Beam with the Built-in Flash Under low-light conditions, when you press the shutter button halfway, the built-in flash fires a brief burst of flashes. It illuminates the subject to enable easier autofocusing.
When Autofocus Fails Autofocus can fail to achieve focus (the focus confirmation light blinks) with certain subjects such as the following: Subjects difficult to focus Low-contrast subjects (Example: Blue sky, solid-color walls, etc.) Subjects in low light Extremely backlit or reflective subjects (Example: Car with a reflective body, etc.) Near and far subjects covered by an AF point (Example: Animal in a cage, etc.) Repetitive patterns (Example: Skyscraper windows, computer keyboards, etc.
i Selecting the Drive ModeN Single and continuous drive modes are provided. In the Basic Zone modes, the optimum drive mode is set automatically. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel, turn the <5> dial. u : Single shooting When you press the shutter button completely, one shot will be taken. o: High-speed continuous shooting (Max. 6.3 shots per sec.) i : Low-speed continuous shooting (Max. 3 shots per sec.
j Self-timer Operation Use the self-timer when you want to be in the picture. The (10 sec. timer) can be used in all shooting modes. 1 Press the button. (9) the self-timer. 2 Select Look at the LCD panel and turn the <5> dial. j : 10-sec. self-timer l : 2-sec. self-timerN the picture. 3 TakeFocus the subject and press the shutter button completely. X You can check the self-timer operation with the self-timer lamp, beeper, and countdown display (in seconds) on the LCD panel.
5 Advanced Operations ve Cre at i Zo ne Y P O With the Creative Zone modes, you can set the desired shutter speed or aperture to obtain the result you want. You take control of the camera. C The M icon on the right of the page title indicates that the respective feature is available only in the Creative Zone modes (d, s, f, a, 8). After you press the shutter button halfway and let go, the LCD panel and viewfinder information will remain displayed for about 4 sec. (0).
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . the subject. 2 Focus Look through the viewfinder and aim the selected AF point over the subject. Then press the shutter button halfway.
d: Program AE If the “30"” shutter speed and the maximum aperture blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the minimum aperture blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and <1> (Full Auto) With <1>, many functions such the AF mode, drive mode, and built-in flash are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the correct exposure matching the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or moving subject. Or a slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Frozen action (Fast shutter speed) 1 Y P O Blurred motion (Slow shutter speed) Set the Mode Dial to .
s: Shutter-Priority AE If the maximum aperture blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the minimum aperture blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the correct exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (smaller f/number) until the blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (larger f/number) until the blinking stops or set a lower ISO speed. Aperture Display The larger the f/number, the smaller the aperture opening will be.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available handheld exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . the shutter speed and 2 Set aperture. To set the shutter speed, turn the <6> dial. To set the aperture, set the power switch to , and turn the <5> dial.
8: Automatic Depth-of-Field AE Objects in the foreground and background will be in focus automatically. All the AF points will function to detect the subject, and the aperture required to attain the necessary depth of field will be set automatically. * <8> stands for Auto-Depth of field. This mode sets the depth of field automatically. 1 Set the Mode Dial to <8>. the subject. 2 Focus Aim the AF points over the subjects and press the shutter button halfway (0).
q Selecting the Metering ModeN The metering mode is the method of measuring the brightness of the subject. In the Basic Zone modes, evaluative metering is set automatically. 1 Press the button. (9) the metering mode. 2 Select While looking at the LCD panel, turn the <6> dial. Y P O q Evaluative metering This is an all-around metering mode suited for portraits and even backlit subjects. The camera sets the exposure automatically to suit the scene.
Setting Exposure CompensationN Exposure compensation is used to alter the standard exposure set by the camera. You can make the image look brighter (increased exposure) or darker (decreased exposure). You can set the exposure compensation up to ±2 stops in 1/3-stop increments. 1 Turn the Mode Dial to any Creative Zone mode except . the exposure level 2 Check indicator. Press the shutter button halfway and check the exposure level indicator.
3 Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±2 stops in 1/3-stop increments for three successive shots. This is called AEB. 1 Select [Expo. comp./AEB]. Under the [2] tab, select [Expo. comp./AEB], then press <0>. the AEB amount. 2 SetTurn the <6> dial to set the AEB AEB amount amount. You can set the exposure compensation amount with the <5> dial.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the shot. This is called AE lock. It is effective for backlit subjects. 1 Focus the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button.
Bulb Exposures When bulb is set, the shutter stays open while you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. 1 Set the Mode Dial to . the shutter speed to “buLb.” 2 SetWhile looking at the LCD panel, turn the <6> dial to select “buLb.” The next setting after “30" ” is “buLb.
Bulb Exposures Using the Eyepiece Cover If you take a picture without looking at the viewfinder, light entering the eyepiece can throw off the exposure. To prevent this, use the eyepiece cover (p.23) attached to the camera strap. 1 Remove the eyecup. Push the bottom of the eyecup upward. the eyepiece cover. 2 Attaching Slide the eyepiece cover down into the eyepiece groove to attach it.
Mirror LockupN Although using the self-timer or Remote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations can also help when you use a super telephoto lens or shoot close ups. When [8C.Fn III -6: Mirror lockup] is set to [1: Enable] (p.180), shooting with mirror lockup will be possible. 1 Focus the subject, press the shutter button completely and release it. X The mirror will swing up. 2 Press the shutter button completely again.
Using the Built-in Flash E-TTL II autoflash obtains high-precision and consistent flash shots. Using the Built-in Flash in the Basic Zone If necessary, the built-in flash will pop-up automatically in low-light or backlit conditions. (except in <3> <5> <7> modes) Using the Built-in Flash in the Creative Zone Regardless of the light level, you can press the button to pop-up and fire the built-in flash whenever desired. If the built-in flash has popped up, you can push it back down with your fingers.
Using the Built-in Flash Effective Range of Built-in Flash Aperture [Approx. meters/feet] ISO Speed 100 200 400 800 1600 3200 H1: 6400 H2: 12800 f/3.5 3.7 / 12.1 5.3 / 17.4 7.4 / 24.3 10.5 / 34.4 14.9 / 48.9 21.0 / 68.9 29.7 / 97.4 42.0 / 137.8 f/4 3.3 / 10.8 4.6 / 15.1 6.5 / 21.3 9.2 / 30.2 13.0 / 42.7 18.4 / 60.4 26.0 / 85.3 36.8 / 120.7 2.3 / 7.5 4.6 / 15.1 6.6 / 21.7 18.6 / 61.0 26.3 / 86.3 f/5.6 3.3 / 10.8 9.3 / 30.5 13.1 / 43.
Using the Built-in Flash y Flash Exposure CompensationN In the same way as normal exposure compensation, you can set exposure compensation for flash. You can set flash exposure compensation up to ±2 stops in 1/3-stop increments. 1 Increased exposure Press the button. (9) the exposure compensation amount. 2 SetWhile looking at the LCD panel or viewfinder, turn the <5> dial. To cancel the flash exposure compensation, set the flash exposure compensation amount back to .
Using the Built-in Flash A FE LockN FE (flash exposure) lock obtains and locks the correct flash exposure reading for any part of a subject. 1 Press the button to pop-up the built-in flash. Press the shutter button halfway and look in the viewfinder to check that the icon is lit. 2 Focus the subject. the button. (8) 3 Press Aim the viewfinder center over the subject Y P O where you want to lock the flash exposure, then press the button.
3 Flash ControlN The built-in flash and an external Speedlite can also be set with the menu. The menu for the external Speedlite will be applicable only to EX-series Speedlites whose functions can be set with the camera. Select [Flash control]. Under the [7] tab, select [Flash control], then press <0>. X The flash control screen will appear. About [Flash firing] Normally, set this to [Enable]. If [Disable] is set, both the built-in flash and external Speedlite will not fire.
3 Flash ControlN E-TTL II For normal flash exposures, set it to [Evaluative]. If [Average] is set, the flash exposure will be averaged for the entire metered scene as with an external metering flash. Flash exposure compensation may be necessary depending on the scene, so this setting is for advanced users. Setting an External Speedlite Select either [External flash func. setting] or [External flash C.Fn setting].
External Speedlites EOS-dedicated, EX-series Speedlites Basically operates like a built-in flash for easy operation. When an EX-series Speedlite is attached to the camera, almost all the autoflash control is done by the camera. In other words, it is like a highoutput flash attached externally in place of the built-in flash. For detailed instructions, see the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites.
External Speedlites Using Non-Canon Flash Units Sync Speed The camera can synchronize with non-Canon compact flash units at 1/250 sec. and slower speeds. With large studio flash units, since the flash duration is longer, set the sync speed within 1/60 sec. to 1/30 sec. Be sure to test the flash synchronization before shooting. PC Terminal The camera’s PC terminal can be used with flash units having a sync cord. The PC terminal is threaded to prevent inadvertent disconnection.
6 Live View Shooting Y P O You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting.” Live View shooting is effective for still subjects which do not move. If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images. Using a tripod is recommended.
Preparing for Live View ShootingN Set the camera for Live View shooting. 1 Set the shooting mode. Set the shooting mode to a Creative Zone mode. Live View shooting does not work in Basic Zone modes. [Live View function 2 Select settings]. Under the [6] tab, select [Live View function settings], then press <0>. Y P O [Live View shoot.]. 3 Select Turn the <5> dial to select [Live View shoot.], then press <0>. Turn the <5> dial to select [Enable], then press <0>. C other functions.
Preparing for Live View ShootingN the Live View image. 5 Display Press the button. X The Live View image will appear on the LCD monitor. Press the button again to turn off the LCD monitor and return to normal shooting. About [Exposure simulation] Exposure simulation displays and simulates how the brightness of the actual image will look.
ShootingN 1 Use AF to focus. Press the
button. X The camera will focus with the current AF mode (p.121). the picture. 2 TakePress the shutter button completely. X The picture will be taken and the captured image is displayed on the LCD monitor. X After the image review ends, the camera will return to Live View shooting automatically.
ShootingN Pressing the button will display the menu screen so you can set menu functions. Press the button again to return to the Live View image. If you select [2 Dust Delete Data], [6 Sensor cleaning], [7 Clear settings], or [7 Firmware Ver.], the Live View shooting will be terminated. Battery Life with Live View Shooting [Approx.
ShootingN About the Information Display Each time you press the button, the information display will change.
Using AF to FocusN Selecting the AF Mode Three AF modes are provided: [Quick mode], [Live mode] (p.123), and [Liveu mode] (face detection) (p.124). If you want to achieve precise focusing, magnify the image and focus manually (p.127). Select the AF mode. Under [6 Live View function settings], select [AF mode]. While the Live View image is displayed, if you press the button, you can also select the AF mode with the <6> dial.
Using AF to FocusN the AF point. 2 Select Press the button, then use <9> to select the AF point. If you keep tilting <9> in the same direction, it will toggle between manual and automatic AF point selection. the subject. 3 Focus Aim the AF point over the subject, and hold down the button. X The Live View image will turn off, the reflex mirror will go back down, and AF will be executed. X When focus is achieved, the beeper will sound and the Live View image will reappear.
Using AF to FocusN Live Mode The image sensor is used to focus. Although AF is possible with the Live View image displayed, the AF operation will take longer than with Quick mode. Also, achieving focus may be more difficult than with Quick mode. 1 AF point Display the Live View image. Press the button. X The Live View image will appear on the LCD monitor. The AF point < > will appear. You can use <9> to move the AF point to where you want to focus (it cannot go to the edges of the picture).
Using AF to FocusN Liveu (Face Detection) Mode With the same AF method as with the Live mode, the human face is detected and focused. Have the person face the camera. 1 Display the Live View image. Press the button. X The Live View image will appear on the LCD monitor. When a face is detected, the frame will appear over the face to be focused. If multiple faces are detected, will be displayed. Use the <9> to move the frame over the target face. Y P O the subject.
Using AF to FocusN The face-detecting AF point might cover only part of the face. An object other than a human face might be detected as a face. Face detection will not work if the face is very small or large in the picture, too bright or too dark, titled horizontally or diagonally, or partially hidden. When you press <9> straight down, it will switch to the Live mode (p.123). You can tilt the <9> to switch to another AF point.
Using AF to FocusN Shooting conditions which can make focusing difficult: Low-contrast subjects such as the blue sky and solid-color surfaces. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Under a light source whose brightness, color, or pattern keeps changing. Night scenes or points of light. Under fluorescent lighting or when the image flickers. Extremely small subjects. Subjects strongly reflecting light.
Focusing ManuallyN Magnify the image and focus manually. 1 Set the lens focus mode switch to . Turn the lens focusing ring to focus roughly. the magnifying frame to the 2 Move position where you want to focus. Use <9> to move the magnifying frame. If you press <9> straight down, it will return to the image center. Magnifying frame Y P O the image. 3 Magnify Press the button. X The image within the magnifying frame will be magnified.
Silent ShootingN Instructions for setting the [6 Live View function settings] menu’s [Silent shoot.] are explained below. Mode 1 The shooting operation noise is quieter than the normal shooting. Continuous shooting is also possible. High-speed continuous shooting will be approx. 5.8 fps. Mode 2 When you press the shutter button completely, only one shot will be taken. While you keep holding down the shutter button, the camera operation will be suspended.
Notes about the Live View image Under low light or bright light conditions, the Live View image might not reflect the brightness of the captured image. If the light source within the image changes, the screen might flicker. If this happens, stop and resume the Live View shooting under the actual light source to be used. If you point the camera in a different direction, it might throw off the Live View image’s correct brightness momentarily. Wait until the brightness level stabilizes before shooting.
Notes about Custom Functions Live View shooting will disable some Custom Function settings (p.173). If [8C.Fn II -4: Auto Lighting Optimizer] (p.177) is not set to [3: Disable], the image will look bright even if a decreased exposure compensation has been set. Notes about lenses and flash The focus preset feature on super telephoto lenses cannot be used. FE lock is not possible when the built-in flash or external Speedlite is used. Modeling flash is not possible when external Speedlite is used.
7 Image Playback Y P O This chapter explains how to playback and erase images, how to display images on a TV screen, and other playback-related functions. C About images taken with another camera: The camera might not be able to properly display images captured with a different camera or edited with a personal computer or whose file name was changed.
x Image Playback Single Image Display 1 Playback the image. Press the button. X The last captured image or last image viewed will appear. the image. 2 Select To playback images starting with the last image, turn the <5> dial counterclockwise. To playback images starting with the first captured image, turn the dial clockwise. Press the button to change the display format.
x Image Playback B Shooting Information Display Protect Exposure compensation amount AF Microadjustment Folder number - File number Flash exposure compensation amount Aperture Shutter speed Card Histogram (Brightness/RGB) Metering mode ISO speed Shooting mode Highlight tone priority Picture Style and settings Color temperature if
is set Image-recording quality Playback number/ Total images recorded White balance White balance correction C Y P O Color space Date and time Original decision (i
x Image Playback About the Histogram The brightness histogram display shows the exposure level distribution and overall brightness. And the RGB histogram display is for checking the color saturation and gradation. The display can be switched with the [4 Histogram] menu. [Brightness] Display Sample Histograms This histogram is a graph showing the distribution of the image’s brightness level.
x Searching for Images Quickly H Display Multiple Images on One Screen (Index display) Search for images quickly with the index display showing four or nine images on one screen. 1 Turn on the index display. During image playback, press the button. X The 4-image index display will appear. The currently-selected image will be highlighted in a blue frame. Press the button again to switch to the 9-image index display. Î Y P O Î C2 Select the image.
x Searching for Images Quickly I Jump through Images (Jump display) With the single image display, index display, and magnified view, you can turn the <6> dial to jump through the images. 1 Select the jump method. With the [4 Image jump w/6] menu’s [1 image/10 images/100 images/Screen/Date/Folder] option, you can set the desired jump method. With the index display, you can jump by a single screen by selecting [Screen]. If you want to jump by date, select [Date]. To jump by folder, select [Folder].
u/y Magnified View You can magnify the image by 1.5x to 10x on the LCD monitor. 1 Magnified area position Magnify the image. During image playback, press the button. X The image will be magnified. To increase the magnification, hold down the button. The image will continue to be magnified until it reaches the maximum magnification. Press the button to reduce the magnification. If you hold down the button, the image will continue to reduce to the single image display. Y P O around the image.
b Rotating the Image You can rotate the image to the desired orientation. 1 Select [Rotate]. Under the [3] tab, select [Rotate], then press <0>. the image. 2 Select Turn the <5> dial to select the image to be rotated. You can also select an image on the index display. Y P O the image. 3 Rotate Each time you press <0>, the image will rotate clockwise as follows: 90° → 270° → 0° To rotate another image, repeat steps 2 and 3. C To exit and return to the menu, press the button.
3 Auto Playback (Slide Show) You can playback the images in the card as an automatic slide show. 1 Quantity of images for playback Select [Slide show]. Under the [4] tab, select [Slide show], then press <0>. X The slide show setting screen appears. the images to be played 2 Select back. Turn the <5> dial to select the item, then press <0>. Turn the <5> dial to select the desired playback images, then press <0>. Item Y P O Playback Images jAll images All the images in the card will be played back.
3 Auto Playback (Slide Show) the Play time and Repeat 3 Set options. Turn the <5> dial to select [Set up], then press <0>. Set the [Play time] and [Repeat] options, then press the button. [Play time] [Repeat] Y P O show. 4 StartTurnthetheslide <5> dial to select [Start], then press <0> X After [Loading image...] is displayed for a few seconds, the slide show will start. To pause the slide show, press <0>. During pause, [ ] will be displayed on the upper left of the image.
Viewing the Images on TV You can also view the images on a TV set. Turn off the camera and the television before connecting them. * Depending on the TV monitor, part of the image might be cut off. Viewing on Non-HD (Hi-Definition) TV Sets 1 Connect the provided video cable to the camera. Connect the video cable to the camera’s
Viewing the Images on TV Viewing on HD (Hi-Definition) TV Sets The HDMI Cable HTC-100 (sold separately) is required. 1 Connect the HDMI cable to the camera. Connect the HDMI cable to the camera’s terminal. With the plug’s logo facing the front of the camera, insert it into the camera’s terminal. the HDMI cable to the TV 2 Connect set. Connect the HDMI cable to the TV’s HDMI IN port. Y P O on the TV and switch the 3 Turn TV’s video input to select the C connected port.
K Protecting Images Protecting the image prevents it from being erased accidentally. 1 Image protect icon Select [Protect images]. Under the [3] tab, select [Protect images], then press <0>. X The protect setting screen will appear. the image and protect it. 2 Select Turn the <5> dial to select the image to be protected, then press <0>. X When an image is protected, the icon will appear on the screen. To cancel the image protection, press <0> again. The icon will disappear.
L Erasing Images You can either select and erase images one by one or erase them in one batch. Protected images (p.143) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect it. Erasing a Single Image 1 Playback the image to be erased. the button. 2 Press The erase menu will appear at the bottom of the screen. 3 Erase the image.
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness You can adjust the brightness of the LCD monitor to make it easier to read. 1 Select [LCD brightness]. Under the [6] tab, select [LCD brightness], then press <0>. the brightness. 2 Adjust While referring to the gray chart, turn the <5> dial, then press <0>. You can also display the [LCD brightness] screen with the button. Y P O To check the image’s exposure, you should look at the histogram (p.134).
Changing Image Playback Settings 3 Auto Rotate of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and personal computer instead of horizontally. The setting of this feature can be changed. 1 Select [Auto rotate]. Under the [5] tab, select [Auto rotate], then press <0>. the auto rotate. 2 SetTurn the <5> dial to select the setting, then press <0>.
8 Sensor Cleaning Y P O The camera has a Self Cleaning Sensor Unit attached to the image sensor’s front layer (low-pass filter) to shake off dust automatically. The Dust Delete Data can also be appended to the image so that the dust spots remaining can be erased automatically by Digital Photo Professional (provided software).
3 Automatic Sensor Cleaning Whenever you set the power switch to <1/J> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not be aware of this operation. However, you can execute the sensor cleaning at anytime as well as disable it. Cleaning the Sensor Now 1 Select [Sensor cleaning]. Under the [6] tab, select [Sensor cleaning], then press <0>. [Clean nowf].
3 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that might be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image to later erase the dust spots. The Dust Delete Data is used by Digital Photo Professional (provided software) to erase the dust spots automatically. Preparation Get a solid-white object (paper, etc.). Set the lens focal length to 50mm or longer.
3 Appending Dust Delete DataN a solid-white object. 3 Photograph At a distance of 20 cm - 30 cm / 0.7 ft. 1.0 ft., fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in the aperture-priority AE mode with an aperture of f/22. Since the image will not be saved, the data can still be obtained even if there is no card in the camera. X When the picture is taken, the camera will start obtaining the Dust Delete Data.
3 Manual Sensor CleaningN Dust which could not be removed by the automatic sensor cleaning can be removed manually with a blower, etc. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. Before cleaning the sensor, detach the lens from the camera. 1 Select [Sensor cleaning]. Under the [6] tab, select [Sensor cleaning], then press <0>. [Clean manually].
3 Manual Sensor CleaningN While cleaning the sensor, never do any of the following. Doing any of the following will cut off the power and close the shutter. The shutter curtains and image sensor might get damaged. • Setting the power switch to <2>. • Opening the battery compartment cover. • Opening the card slot cover. The surface of the image sensor is extremely delicate. Clean the sensor with care. Use a plain blower without any brush attached. A brush can scratch the sensor.
9 Printing Images and Transferring Images to a Computer Y P O Printing (p.154) You can connect the camera directly to a printer and print out the images in the card. The camera is compatible with “wPictBridge” which is the standard for direct printing. C Digital Print Order Format (DPOF) (p.163) DPOF (Digital Print Order Format) enables you to print images recorded in the card according to your printing instructions such as the image selection, quantity to print, etc.
Preparing to Print You do the direct printing procedure entirely with your camera while you look at the LCD monitor. Connecting the Camera to a Printer 1 Set the camera’s power switch to <2>. the printer. 2 SetForupdetails, see the printer’s instruction manual. Y P O the camera to the 3 Connect printer. Use the interface cable that came with the camera. When connecting the cable plug to the camera’s terminal, the cable plug’s icon must face the front side of the camera.
Preparing to Print wPictBridge the image. 6 Playback Press the button. X The image will appear, and the icon will appear on the upper left to indicate that the camera is connected to a printer. X The button lamp will light in blue. C Y P O The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct. When connecting the camera to the printer, do not use any cable other than the interface cable provided.
wPrinting The screen display and setting options will differ depending on the printer. Some settings might not be available. For details, see the printer’s instruction manual. Printer-connected icon 1 Select the image to be printed. Check that the icon is displayed on the upper left of the LCD monitor. Turn the <5> dial to select the image to be printed. <0>. 2 Press X The print setting screen will appear. Print setting screen Y P O Sets the printing effects (p.158).
wPrinting QSetting the Paper Size Select the size of the paper loaded in the printer, then press <0>. X The paper type screen will appear. YSetting the Paper Type Select the type of the paper loaded in the printer, then press <0>. When using a Canon printer and Canon paper, read the printer’s instruction manual to check what paper types can be used. X The page layout screen will appear. Y P O USetting the Page Layout Select the page layout, then press <0>. X The print setting screen will reappear.
wPrinting effects. 4 SetSettheasprinting necessary. If you need not set any printing effects, go to step 5. The screen display may differ depending on the printer. Select the option on the upper right, then press <0>. Select the desired printing effect, then press <0>. If the icon is displayed next to , you can also adjust the printing effect (p.160). Item Description EOn The image will be printed according to the printer’s standard colors.
wPrinting the date and file number 5 Set imprinting. Set as necessary. Select , then press <0>. Set as desired, then press <0>. of copies. 6 SetSettheasnumber necessary. Select , then press <0>. Set the number of copies, then press <0>. Y P O printing. 7 StartSelect [Print], then press <0>. X The button’s blue lamp will blink and the printing will start. C With Easy printing, you can print another image with the same settings. Just select the image and press the button lit in blue.
wPrinting e Adjustment of Printing Effects In step 4 on page 158, select the printing effect. When the icon is displayed next to , press the button. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4. Brightness The image brightness can be adjusted. Adjust levels When you select [Manual], you can change the histogram’s distribution and adjust the image’s brightness and contrast.
wPrinting Trimming the Image Tilt correction You can crop the image and print only the trimmed portion as if the image was recomposed. Do the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again. 1 On the print setting screen, select [Trimming]. 2 Set the trimming frame size, position, and proportion. Y P O The image area within the trimming frame will be printed.
wPrinting Depending on the printer, the trimmed image area might not be printed as you specified. The smaller you make the trimming frame, the grainier the picture will look on the print. While trimming the image, look at the camera’s LCD monitor. If you look at the image on a TV screen, the trimming frame might not be displayed accurately. Handling Printer Errors If you resolve a printer error (no ink, no paper, etc.
Digital Print Order Format (DPOF) You can set the print type, date imprinting, and file No. imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) Setting the Printing Options 1 Select [Print order]. X Under the [3] tab, select [Print order], then press <0>. [Set up]. 2 Select Select [Set up], then press <0>. C3 Y P O Set the option as desired. [Print type] Set the [Print type], [Date], and [File No.].
Digital Print Order Format (DPOF) Print type Date File number K Standard Prints one image on one sheet. L Index Multiple, thumbnail images are printed on one sheet. K L Both Prints both the standard and index prints. On Off On Off [On] imprints the recorded date on the print. [On] imprints the file No. on the print. 4 Exit the setting. Press the <7> button. X The print order screen will reappear. Y P O Next, select [Sel.Image], [Byn], or [All image] to order the images to be printed.
Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. Press the button to display the three-image view. To return to the singleimage display, press the button. After completing the print order, press the button to save the print order to the card. Quantity Total images selected Check mark Index icon [Standard] [Both] Press <0> and a print order for 1 copy of the displayed image will be placed.
Direct Printing with DPOF With a PictBridge printer, you can easily print images with DPOF. 1 Preparing to print. See page 154. Follow the “Connecting the Camera to a Printer” procedure up to step 5. 2 Under the [3] tab, select [Print order]. 3 Select [Print]. Y P O [Print] will be displayed only if the camera is connected to the printer and printing is possible. 4 Set the [Paper settings]. (p.156) C Set the printing effects (p.158) if necessary. 5 Select [OK].
d Transferring Images to a Personal Computer By connecting the camera to a personal computer, you can transfer images from the camera’s card by operating the camera. This feature is called direct image transfer. Before connecting the camera to a personal computer, be sure to install the provided software (EOS DIGITAL Solution Disk on CD-ROM) in the personal computer. For instructions to install the provided software, see the separate sheet, CD-ROM Guide.
d Transferring Images to a Personal Computer Shooting will be disabled while the direct transfer screen is displayed. If the [EOS Utility] screen does not appear, see Software Instruction Manual in the CD-ROM. Before disconnecting the cable, turn off the camera. Pull out the cable by grasping the plug (instead of the cord).
d Transferring Images to a Personal Computer Options other than [All Images] are explained below. To start the image transfer, press the button. New images Images which have not yet been transferred to the personal computer will be selected by the camera automatically and transferred. Transfer order images You select the images and they are transferred to the personal computer in a batch. To select the images, see page 170. Select & transfer You select the images individually to be transferred.
d Transferring Images to a Personal Computer 3 Selecting the Images to be Transferred Under the [3] tab, you can use [Transfer order] to select the images to be transferred to a personal computer. When you select [Transfer order images] on page 169, you can transfer the images set by the transfer order. Sel.Image Select and order images one by one. Press <0> to include the displayed image in the transfer order. The icon will also appear on the upper left.
10 Customizing the Camera Y P O With Custom Functions, you can change the camera functions according to your preference. Also, the current camera settings can be saved under the Mode Dial’s and positions. The functions explained in this chapter apply to Creative Zone modes.
3 Setting Custom FunctionsN 1 Select [8]. Turn the <6> dial to select the [8] tab. the group. 2 Select Turn the <5> dial to select C.Fn I IV, then press <0>. Custom Function No. the Custom Function 3 Select number. Turn the <5> dial to select the Custom Function No., then press <0>. 4 Change the setting as desired. Y P O Turn the <5> dial to select the setting (number), then press <0>. Repeat steps 2 to 4 if you want to set other Custom Functions.
3 Custom FunctionsN C.Fn I: Exposure 1 2 3 4 5 6 7 Exposure level increments ISO speed setting increments ISO expansion Bracketing auto cancel Bracketing sequence Safety shift Flash sync. speed in Av mode p.174 p.175 C.Fn II: Image 1 2 3 4 Long exposure noise reduction High ISO speed noise reduction Highlight tone priority Auto Lighting Optimizer C.
3 Custom Function SettingsN C.Fn I: Exposure C.Fn I -1 Exposure level increments 0: 1/3-stop 1: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, etc. Effective when you prefer to control the exposure in less fine increments than 1/3-stop increments. The exposure level will be displayed in the viewfinder and on the LCD panel as shown below. C.Fn I -2 ISO speed setting increments 0: 1/3-stop 1: 1-stop C.
3 Custom Function SettingsN C.Fn I -5 Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0: 0, -, + 1: -, 0, + WB Bracketing B/A Direction M/G Direction 0 : Standard exposure 0 : Standard white balance 0 : Standard white balance - : Decreased exposure - : More blue - : More magenta + : Increased exposure + : More amber + : More green AEB C.
3 Custom Function SettingsN C.Fn II: Image C.Fn II -1 Long exposure noise reduction 0: Off 1: Auto For 1 sec. or longer exposures, noise reduction is performed automatically if noise typical of long exposures is detected. This [Auto] setting is effective in most cases. 2: On Noise reduction is performed for all exposures of 1 sec. or longer. The [On] setting may be effective for noise that cannot be detected or reduced with the [Auto] setting.
3 Custom Function SettingsN C.Fn II -3 Highlight tone priority 0: Disable 1: Enable Improves the highlight detail. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. With setting 1, noise in the shadow areas may be slightly more than usual. With setting 1, the settable ISO speed range will be 200 - 3200. Also, (dynamic range) will be displayed on the LCD panel and in the viewfinder. C.
3 Custom Function SettingsN C.Fn III: Autofocus/Drive C.Fn III -1 Lens drive when AF impossible If autofocus is executed, but focus cannot be achieved, the camera can either keep trying to focus or stop. 0: Focus search on 1: Focus search off Prevents the camera from becoming grossly out of focus as it attempts to focus again. Especially convenient with super telephoto lenses which can become extremely out of focus. C.
3 Custom Function SettingsN C.Fn III -3 AF point selection method 0: Normal Press the button and use <9> to select the AF point. 1: Multi-controller direct Without pressing the button first, you can just use <9> to select the desired AF point. Pressing the button will set it to automatic AF point selection. 2: Quick Control Dial direct Without pressing the button first, you can just use the <5> to select the desired AF point.
3 Custom Function SettingsN C.Fn III -6 Mirror lockup 0: Disable 1: Enable Prevents camera vibrations caused by the reflex mirror action which can disturb shooting with super telephoto lenses or close-up (macro) shooting. See page 106 for the mirror lockup procedure. C.Fn III -7 AF Microadjustment Normally, this adjustment is not required. Do this adjustment only if necessary. Note that doing this adjustment may prevent correct focusing from being achieved.
3 Custom Function SettingsN It is best to make the adjustment at the actual place to be photographed. This will make the adjustment more precise. With setting 2, if an Extender is used, the adjustment will be registered for the lens and Extender combination. The registered AF microadjustments will be retained even if you use the Custom Function to clear all settings (p.172). However, the setting itself will be [0: Disable]. C.Fn IV: Operation/Others C.
3 Custom Function SettingsN C.Fn IV -3 Assign SET button You can assign a frequently-used function to <0>. When the camera is ready to shoot, you can press <0>. 0: Normal (disabled) 1: Image quality Press <0> to display the image-recording quality setting screen on the LCD monitor. Turn the <6> or <5> dial to set the desired imagerecording quality, then press <0>. 2: Picture Style Press <0> to display the Picture Style selection screen on the LCD monitor.
3 Custom Function SettingsN C.Fn IV -5 Focusing Screen If you change the focusing screen, change this setting to match the focusing screen type. This is to obtain the correct exposures. 0: Ef-A 1: Ef-D 2: Ef-S About focusing screen characteristics Ef-A: Standard Precision Matte Standard focusing screen that comes with the camera. Provides good viewfinder brightness and enables easy manual focusing. Ef-D: Precision Matte with grid This is the Ef-A with a grid.
3 Custom Function SettingsN C.Fn IV -6 Add original decision data 0: Off 1: On Data for verifying whether the image is original or not is appended to the image automatically. When the shooting information of an image appended with the verification data is displayed (p.133), the icon will appear. To verify whether the image is original, the Original Data Security Kit OSK-E3 (sold separately) is required.
3 Registering My MenuN For faster access, you can register up to six menus and Custom Functions whose settings you change frequently. 1 Select [My Menu settings]. Under the [9] tab, select [My Menu settings], then press <0>. [Register]. 2 Select Turn the <5> dial to select [Register], then press <0>. the desired items. 3 Register Turn the <5> dial to select the item, C then press <0>. When the confirmation dialog appears and you select [OK] and press <0>, the menu will be registered.
3 Register Camera User SettingsN Under the Mode Dial’s and positions, you can register most of the current camera settings containing your preferred shooting mode, menus, Custom Function settings, etc. 1 Select [Camera user setting]. Under the [7] tab, select [Camera user setting], then press <0>. 2 Select [Register]. the desired items. 3 Register Turn the <5> dial to select the Mode Y P O Dial position where the camera settings are to be registered, then press <0>.
11 Reference Y P O This chapter provides reference information for camera features, system accessories, etc. The back of this chapter also has an index to make it easier to look up things.
B Checking Camera Settings When the camera is ready to shoot, press the button and “Camera settings” and “Shooting functions” screens will appear. When “Shooting functions” is displayed, you can set the shooting functions while looking at the LCD monitor. Display “Camera set.” and “Shoot. func.” Press the button. X The button toggles between the two screens. Display one of them. Under the [7] tab, select [INFO. button], then press <0>. Select [Camera set.] or [Shoot. func.], then press <0>.
B Checking Camera Settings Shooting Functions AE lock Aperture Shutter speed Picture Style ISO speed Highlight tone priority Exposure level/ AEB range Flash exposure compensation Shooting mode AF point Metering mode Image-recording quality Drive mode Shots remaining Quick Control icon Y P O White balance Battery check AF mode White balance correction C Maximum burst When you press <9> straight down, the Quick Control screen appears (p.38).
Using a Household Power Outlet With AC Adapter Kit ACK-E2 (sold separately), you can connect the camera to a household power outlet and not worry about the battery level. 1 Connect the DC plug. Connect the DC Coupler’s plug to the AC adapter’s socket. the power cord. 2 Connect Connect the power cord to the AC adapter. Insert the prongs into a power outlet. After using the camera, unplug the power plug from the power outlet. Y P O the cord in the groove.
Replacing the Date/Time Battery The date/time (back-up) battery maintains the camera’s date and time. Its service life is about 5 years. If the date/time is reset when the battery is replaced, replace the back-up battery with a new CR2016 lithium battery as described below. The date/time setting will also be reset, so be sure to set the correct date/time. 1 Set the power switch to <2>. 2 Remove the battery. Y P O 3 Take off the battery holder. (+) (–) C4 Replace the battery.
Using the Battery Grip These are supplemental instructions for using Battery Grip BG-E2 with this camera. For instructions other than “Detaching the Battery Compartment Cover” and “Battery Life” explained below, refer to the Battery Grip BG-E2 Instruction Manual. If you have Battery Grip BG-E2N, read the BG-E2N’s Instruction Manual. Detaching the Battery Compartment Cover Put the camera on a flat surface and hold it firmly so it does not fall.
Menu Settings 1 Shooting 1 (Red) Page Quality 73 / 83 / 74 / 84 / 76 / 86 1 / D1 / D2 60 Red-eye On/Off Off / On 108 Beep On / Off - Shoot w/o card On / Off 29 Review time Off / 2 sec. / 4 sec. / 8 sec. / Hold 145 Peripheral illumin. correct. Enable / Disable 76 Expo. comp.
Menu Settings 4 Playback 2 (Blue) Page Highlight alert Disable / Enable 133 AF point disp. Disable / Enable 133 Histogram Brightness / RGB 134 Slide show Set the Play time and Repeat settings for automatic playback of images 139 Image jump w/6 1 image / 10 images / 100 images / Screen / Date / Folder 136 Auto power off 1min. / 2 min. / 4 min. / 8 min. / 15 min. / 30 min.
Menu Settings 7 Set-up 3 (Yellow) Page INFO. button Normal disp. / Camera set. / Shoot. func. 188 Flash control Flash firing / Built-in flash function setting / External flash function setting / External flash C.Fn setting / Clear external flash C.Fn setting 111 Camera user setting Register current camera settings to the Mode Dial’s w or x position 186 Clear settings Clear all camera settings / Delete copyright information 45 Firmware Ver.
Function Availability Table o: Set automatically k: User selectable Mode Dial Basic Zone Quality ISO speed 1 2 3 4 5 6 7 C d s f a 8 JPEG k k k k k k k k k k k k k RAW k k k k k k k k k k k k k RAW + JPEG k k k k k k k k k k k k k Auto o o o o o o o o k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k Preset WB
Function Availability Table o: Set automatically k: User selectable Mode Dial Basic Zone : Not selectable Creative Zone 1 2 3 4 5 6 7 C d o o o o o o o o k k k k k Partial k k k k k Spot k k k k k Center-weighted average k k k k k Evaluative Metering mode Exposure Program shift k*1 k Exposure compensation k*2 s f a 8 k k k k AEB k k k AE lock k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k
Troubleshooting Guide If there is a problem, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power The battery cannot be recharged with the battery charger provided. Do not recharge any battery pack other than genuine Canon Battery Pack BP-511A, BP-514, BP-511, or BP-512. The camera does not operate even when the power switch is set to <1>. The battery is not properly installed in the camera (p.26).
Troubleshooting Guide Shooting No images can be shot or recorded. The card is not properly inserted (p.29). If the card is full, replace the card or delete unnecessary images to make room (p.29, 144). If you try to focus in the One-Shot AF mode while the focus confirmation light in the viewfinder blinks, a picture cannot be taken. Press the shutter button halfway again to focus, or focus manually (p.35, 88). The LCD monitor does not display a clear image.
Troubleshooting Guide Live View shooting is not possible. When using Live View shooting, use a memory card (a hard disk-type card such as MicroDrive is not recommended). A hard disk-type card requires a lower temperature range for operation than normal memory cards. If the temperature gets too high, the Live View shooting may stop temporarily to prevent damage to the card’s hard disk. When the camera’s internal temperature decreases, you can resume the Live View shooting (p.120).
Error Codes Error No. Countermeasures If there is a problem with the camera, an error message appears. Follow the onscreen instructions. To recover from the error screen, turn the power switch <2> and <1>, or remove and reinstall the battery. If error 02 (Card problem) is displayed, remove and reinstall the card or format the card. This may resolve the problem. If the same error keeps appearing, there may be a problem. Write down the error code and consult your nearest Canon Service Center. No.
System Map Eyepiece Extender EP-EX15 ST-E2 Rubber Frame Eb E-series Dioptric Adjustment Lenses 220EX 430EX II 580EX II Macro Ring Lite MR-14EX Bundled Accessories Focusing Screen Ef-A Eyecup Eb C Angle Finder C Wide Strap EW-EOS50D Y P O Focusing Screen Ef-D Ef-S Battery Pack BP-511A Date / time CR2016 lithium battery Battery Pack BP-511A Battery Grip BG-E2N Battery Magazine BGM-E2 202 Macro Twin Lite MT-24EX AC Adapter DC Coupler AC-E2 DR-400 AC Adapter Kit ACK-E2 Car Battery Cable CB-5
System Map Timer Remote Controller TC-80N3 Remote Switch RS-80N3 Wireless Controller LC-5 EF lenses EF-S lenses HDMI Cable HTC-100 Video Cable EOS DIGITAL Software Instruction Solution Disk Manual Y P O Video Cable VC-100 C TV/Video USB external media Wireless File Transmitter WFT-E3/WFT-E3A (Firmware Ver. 2.0.
Specifications • Type Type: Recording media: Image sensor size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera with built-in flash Type I or II CF card, UDMA-compatible 22.3 x 14.9 mm Canon EF lenses (including EF-S lenses) (35mm-equivalent focal length is approx.1.6 times the lens focal length) Canon EF mount • Image Sensor Type: Effective pixels: Aspect ratio: Dust delete feature: CMOS sensor Approx. 15.
Specifications • Viewfinder Type: Coverage: Magnification: Eye point: Built-in dioptric adjustment: Focusing screen: Eye-level pentaprism Vertical/Horizontal approx. 95% Approx. 0.95x (-1 m-1 with 50mm lens at infinity) Approx. 22 mm (From eyepiece lens center at -1m-1) -3.0 - +1.
Specifications • Shutter Type: Shutter speeds: Electronically-controlled, focal-plane shutter 1/8000 sec. to 1/60 sec. (Full Auto mode), X-sync at 1/250 sec. 1/8000 sec. to 30 sec., bulb (Total shutter speed range. Available range varies by shooting mode.) • Flash Built-in flash: External flash: Flash metering: Flash exposure compensation: FE lock: PC terminal: Retractable, auto pop-up flash Guide No.: 13/43 (ISO 100, in meters/feet) Flash coverage: 17mm lens angle of view Recycling time approx. 3 sec.
Specifications • LCD Monitor Type: Monitor size and dots: Coverage: Interface languages: TFT color liquid-crystal monitor (Brightness adjustable to 7 levels) 3-in. with approx. 920,000 dots (VGA) Approx. 100% 25 • Image Playback Image display formats: Single, Single + Info (Image-recording quality, shooting information, histogram), 4-image index, 9-image index, image rotate possible Zoom magnification: Approx. 1.
Specifications • Dimensions and Weight Dimensions (W x H x D): 145.5 x 107.8 x 73.5 mm / 5.7 x 4.2 x 2.9 in. Weight: Approx. 730 g / 25.7 oz. (body only) • Operation Environment Working temperature range: 0°C - 40°C / 32°F - 104°F Working humidity: 85% or less • Battery Pack BP-511A Type: Rated voltage: Battery capacity: Dimensions (W x H x D): Weight: Rechargeable lithium-ion battery 7.4 V DC 1390 mAh 38 x 21 x 55 mm / 1.5 x 0.8 x 2.2 in. Approx. 82 g / 2.9 oz.
Specifications • EF-S18-200mm f/3.5-5.6 IS Angle of view: Diagonal extent: 74°20’ - 7°50’ Horizontal extent: 64°30’ - 6°30’ Vertical extent: 45°30’ - 4°20’ Lens construction: 16 elements in 12 groups Minimum aperture: f/22 - 36 Closest focusing distance: 0.45 m / 1.48 ft. (From image sensor plane) Max. magnification: 0.24x (at 200 mm) Field of view: 452 x 291 - 93 x 62 mm / 17.8 x 11.5 - 3.7 x 2.4 in. (at 0.45 m) Image Stabilizer: Lens shift type Filter size: 72 mm Lens cap: E-72 Max.
Specifications • EF28-135mm f/3.5-5.6 IS USM Angle of view: Diagonal extent: 75° - 18° Horizontal extent: 65° - 15° Vertical extent: 46° - 10° Lens construction: 16 elements in 12 groups Minimum aperture: f/22 - 36 Closest focusing distance: 0.5 m / 1.64 ft. (From image sensor plane) Max. magnification: 0.19x (at 135 mm) Field of view: 551 x 355 - 188 x 125 mm / 21.7 x 14.0 - 7.4 x 4.9 in. (at 0.5 m) Image Stabilizer: Lens shift type Filter size: 72 mm Lens cap: E-72U Max. diameter x length: 78.4 x 96.
Specifications • EF-S18-135mm f/3.5-5.6 IS Angle of view: Diagonal extent: 74°20’ - 11°30’ Horizontal extent: 64°30’ - 9°30’ Vertical extent: 45°30’ - 6°20’ Lens construction: 16 elements in 12 groups Minimum aperture: f/22 - 36 Closest focusing distance: 0.45 m / 1.48 ft. (From image sensor plane) (at 135mm) * The minimum focusing distance varies depending on the lens focal length. Max. magnification: 0.21x (at 135mm) Field of view: 327 x 503 mm / 12.9 x 19.8 in. (at 0.49 m / 1.61 ft.) 75 x 112 mm / 3.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. CompactFlash is a trademark of SanDisk Corporation. Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Macintosh and Mac OS is a trademark or registered trademark of Apple Inc. in the United States and other countries. HDMI, HDMI logo, and High-Definition Multimedia Interface are a trademark or registered trademark of HDMI Licensing LLC.
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. • Keep the camera from the reach of small children. The neck strap can accidentally choke the child.
Digital Camera Model DS126211 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS — This manual contains important safety and operating instructions for Battery Charger CG-580 & CB-5L. 2. Before using the charger, read all instructions and cautionary remarks on (1) the charger, (2) the battery pack, and (3) the product using the battery pack. 3. CAUTION — To reduce risk of injury, charge only the Battery Pack BP-511A, BP-514, BP-511, or BP-512. Other types of batteries may burst, causing personal injury and other damage. 4.
MEMO C Y P O 217
MEMO C 218 Y P O
MEMO C Y P O 219
MEMO C 220 Y P O
MEMO C Y P O 221
MEMO C 222 Y P O
Index A C AC Adapter Kit ..............................190 w, x .................................... 20, 186 Access lamp....................................30 C (Creative Auto) ......................... 57 A-DEP (Automatic depth-of-field AE)..........99 Cable ................................ 3, 141, 142 Adobe RGB.....................................82 AE lock..........................................103 AEB (Auto Exposure Bracketing)....................
Index D Date J Date/Time Date/Time .......................................42 Date/time battery replacement...191 Depth-of-field preview.....................97 Dioptric adjustment .........................34 Direct printing J Printing Drive mode .............................89, 189 Single / Continuous shooting Self-timer ....................................90 Dust Delete Data ..........................149 E Easy printing .................................159 Erase (image) ...............................
Index Hi-Definition ..................................142 J Highlight alert ................................133 JPEG .............................................. 60 Highlight detail loss .......................133 Jump display ................................ 136 Highlight tone priority ....................177 L Histogram......................................134 Brightness / RGB Landscape................................ 52, 65 Household power ..........................190 Language selection ..
Index Metering mode......................100, 189 Evaluative / Partial / Spot / Center-weighted average MF (Manual focusing) .....................88 Picture Style Adjustment................................. 67 Selection .................................... 65 User defined .............................. 69 Mirror lockup .........................106, 180 Pixel count selection ...................... 60 Mode Dial J Shooting mode Playback J Image Monochrome image ..................66, 68 Portrait........
Index Revert to default settings ................45 sRAW (Small RAW).................. 60, 62 Review time ..................................145 Strap ............................................... 23 Rotate (image) ..............138, 146, 161 System map ................................. 202 S T Safety shift ....................................175 Safety warnings ............................213 Toning effect (Monochrome)........... 68 Sepia / Blue / Purple / Green Saturation......................
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.
