INSTRUCTION MANUAL E E INSTRUCTION MANUAL
Thank you for purchasing a Canon product. The EOS 40D is a high-performance, digital SLR camera featuring a fine-detail CMOS sensor with 10.10 effective megapixels, DIGIC III, high-precision and high-speed 9-point AF (all cross-type points), and high-speed 6.5 fps continuous shooting. The camera is highly responsive to any shooting situation at anytime, provides many features for demanding shoots, and expands shooting possibilities with system accessories.
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. The accessories included can also be checked on the System Map (p.178). Camera: EOS 40D (includes eyecup, body cap, and installed battery for the date/time clock) Lens: EF-S18-55mm f/3.5-5.6 IS or EF-S17-85mm f/4-5.6 IS USM * Lens kit only. * The lens included in the lens kit may differ from the above.
Conventions Used in this Manual Icons in this Manual <6> indicates the Main Dial. <5> indicates the Quick Control Dial. <9> indicates the Multi-controller. <0> indicates the SET button. 0, 9 or 8 indicates that the respective function remains active for 4 sec., 6 sec., or 16 sec. respectively after you let go of the button. In this manual, the icons and markings indicating the camera’s buttons, dials, and settings correspond to the icons and markings on the camera and on the LCD monitor.
Contents Introduction Item Check List ..................................................................................................3 Conventions Used in this Manual.......................................................................4 Index to Features ...............................................................................................8 Handling Precautions .......................................................................................12 Quick Start Guide...........................
Contents 6 4 Setting the AF and Drive Modes 5 Advanced Operations 6 Live View Shooting 7 Image Playback 75 Selecting the AF Mode .................................................................................... 76 Selecting the AF Point ..................................................................................... 78 When Autofocus Fails...................................................................................... 80 Manual Focusing ..............................................
Contents 8 9 Sensor Cleaning Direct Printing from the Camera/Digital Print Order Format Transferring Images to a Personal Computer 11 Customizing the Camera 2 3 147 Transferring Images to a Personal Computer ................................................148 4 151 Setting Custom Functions ..............................................................................152 Custom Functions .......................................................................................
Index to Features Power White balance Battery • Charging • Battery check Î p.24 Î p.26 White balance selection Î p.67 Color temperature setting Î p.69 Power outlet Î p.170 White balance correction Î p.70 Auto power off Î p.42 WB bracketing Menus & Basic Settings Î p.68 Î p.71 AF Menus Î p.38 AF mode Î p.76 Camera setting display Î p.168 AF point selection Î p.78 Manual focusing Î p.80 LCD brightness adjustment Î p.125 Language Î p.41 Date/Time Î p.41 Beeper Î p.
Index to Features Exposure adjustment Exposure compensation Î p.93 AEB Î p.94 AE lock Î p.95 Exposure level increments Î p.154 Flash Auto rotate of vertical images Î p.126 Image protect Î p.123 Image erase Î p.124 Video OUT Î p.122 Camera Direct Printing/DPOF PictBridge Î p.133 Built-in flash Î p.99 Print Order (DPOF) Î p.143 External flash Î p.105 Image transfer • Transfer order Î p.148 Î p.150 External flash control • Flash settings Î p.103 • Flash Custom Functions Î p.
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. • Keep the camera from the reach of small children. The neck strap can accidentally choke the child.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe with a well-wrung wet cloth. Never leave the camera near anything having a strong magnetic field such as a magnet or electric motor.
Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there might be a few dead pixels among the remaining 0.01% or less pixels. Dead pixels displaying only black or red, etc., are not a malfunction. They do not affect the images recorded. If the LCD monitor is left on for a prolonged period, screen burn-in may occur where you see remnants of what was displayed.
Quick Start Guide Insert the battery. (p.26) To recharge the battery, see page 24. 1 2 3 For EF-EF-S S レンズ lens For EF lens Attach the lens. (p.30) When attaching an EF-S lens, align it with the white index on the camera. For other lenses, align it with the red index. Set the lens focus mode switch to . (p.30) Open the CF card slot cover and insert a CF card. (p.28) 4 Face the label side toward you and insert the end with the small holes into the camera. 5 14 Set the power switch to <1>. (p.
Quick Start Guide 6 Set the Mode Dial to <1> (Full Auto). (p.46) 7 Focus the subject. (p.32) 8 Take the picture. (p.32) Press the shutter button completely to take the picture. 9 Review the picture on the LCD monitor. (p.125) All the necessary camera settings will be set automatically. Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus the subject. The captured image will be displayed for about 2 sec.
Nomenclature For detailed information, reference page numbers are provided in parentheses (p.**). Metering mode selection/White balance selection button (p.92/67) AF mode selection/Drive mode selection button (p.76/81) ISO speed set/ Flash exposure compensation button (p.59/101) <6> Main Dial (p.33) LCD panel illumination button (p.96) LCD panel (p.18) EF Lens mount index (p.30) Built-in flash/AF-assist beam (p.99/79) EF-S Lens mount index (p.30) Flash-sync contacts Hot shoe (p.
Nomenclature Focal plane mark AF start button (p.32,76,114) <9> Multi-controller (p.34) Dioptric adjustment knob (p.35) Eyecup (p.97) AE lock/ FE lock button/Index/ Reduce button (p.95/102/119/120,141) Viewfinder eyepiece AF point selection/ Enlarge button (p.78/120,141) Print/ Share button (p.139,149) Menu button (p.36) Strap mount (p.23) LCD monitor (p.36, 125) Jump button (p.119) CF card slot cover (p.28) Erase button (p.124) Playback button (p.
Nomenclature LCD Panel AF point selection ([ - -- --- -- - ]) CF card full warning (FuLL CF) Shutter speed Busy (buSY) Built-in flash recycling (buSY) CF card error warning (Err CF) Image-recording quality No CF card warning (no CF) Error code (Err) 37 38 47 Large/Fine Large/Normal Medium/Fine 48 67 68 Medium/Normal Small/Fine Small/Normal Cleaning image sensor (CLEA n) Aperture Shots remaining Shots remaining during WB bracketing 1 RAW D Small RAW Self-timer countdown Bulb exposure time White
Nomenclature Viewfinder Information Spot metering circle Focusing screen AF points (Superimposed display) ISO speed Focus confirmation light AE lock/ AEB in-progress Max.
Nomenclature Mode Dial The Mode Dial has the Basic Zone modes and Creative Zone modes. Camera User Settings Most camera settings can be registered under w, x, or y. (p.165) Creative Zone These modes give you more control over the result. d : Program AE (p.84) s : Shutter-priority AE (p.86) f : Aperture-priority AE (p.88) a : Manual exposure (p.90) 8 : Automatic depth-of-field AE (p.91) Full Auto Basic Zone All you do is press the shutter button.
Nomenclature EF-S18-55mm f/3.5-5.6 IS lens Focusing ring (p.80,110) Hood EW-60C (sold separately) mount Focus mode switch (p.30) Zoom ring Zoom position index 58 mm filter thread (front of lens) Image Stabilizer switch (p.31) Lens mount index (p.30) Contacts (p.13) EF-S17-85mm f/4-5.6 IS USM lens Focus mode switch (p.30) Zoom position index Focusing ring (p.80,110) Hood EW-73B (sold separately) mount Distance scale 67 mm filter thread (front of lens) Zoom ring Contacts (p.
Nomenclature Battery Charger CG-580 This is a battery pack charger. (p.24) Battery pack slot Power plug Charge lamp This power unit is intended to be correctly orientated in a vertical or floor mount position. IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet.
1 Getting Started This chapter explains preliminary steps and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap. (p.
Recharging the Battery 1 Remove the cover. When you remove the battery from the camera, be sure to reattach the cover to protect against short circuiting. the battery. 2 Attach Align the battery’s front edge with the battery charger’s index line. While pressing down the battery, slide it in the direction of the arrow. To detach the battery, follow the above procedure in reverse. Battery pack slot index CG-580 the battery.
Recharging the Battery Tips for Using the Battery and Charger Recharge the battery on the day before or on the day it is to be used. A charged battery unused will still gradually lose its power over time. After recharging the battery, detach it and unplug the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Installing the Battery Load a fully charged BP-511A battery pack into the camera. 1 Open the battery compartment cover. Slide the lever as shown by the arrow and open the cover. the battery. 2 Insert Point the battery contacts downward. Insert the battery until it locks in place. the cover. 3 Close Press the cover until it snaps shut. Battery Pack BP-514, BP-511, or BP-512 can also be used. Checking the Battery Level When the power switch is set to <1> or (p.
Installing and Removing the Battery Battery Life Temperature [Number of shots • approx.] Shooting Conditions No Flash 50% Flash Use At 23°C / 73°F 1100 800 At 0°C / 32°F 950 700 The figures above are based on a fully-charged BP-511A, no Live View shooting, and CIPA (Camera & Imaging Products Association) testing standards. The actual number of shots may be fewer than indicated above depending on the shooting conditions.
Installing and Removing the CF Card The captured image is recorded onto the CF card (sold separately). Although the thickness is different between the Type I and Type II CF cards, either one can be inserted into the camera. The camera is also compatible with Microdrive (hard disk-type) and CF cards with 2 GB or higher capacity. Installing a Card 1 Label side CF card eject button Open the cover. Slide the cover as shown by the arrow to open it. the CF card.
Installing and Removing the CF Card Removing the Card 1 Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. Access lamp the CF card. 2 Remove Press the CF card eject button. X The CF card will come out. Close the cover. When the access lamp is lit or blinking, it indicates that the images are being written to or read by the CF card, being erased, or data is being transferred. While the access lamp is lit or blinking, never do any of the following.
Mounting and Detaching a Lens Mounting a Lens 1 EF-S lens mount index EF lens mount index Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrow. the lens. 2 Attach Align the EF-S lens with the camera’s white EF-S lens mount index and turn the lens as shown by the arrow until it clicks in place. When attaching a lens other than an EF-S lens, align the lens with the red EF lens mount index. the lens, set the focus mode 3 On switch to .
Mounting and Detaching a Lens About the Image Stabilizer Lenses If an Image Stabilizer (IS) lens is attached and the lens IS switch is set to <1>, the Image Stabilizer will operate when you press the shutter button halfway. When the image in the viewfinder looks steady, take the picture. For bulb exposures, set the IS switch to <2>. If it is set to <1>, the Image Stabilizer may malfunction. The Image Stabilizer continues to operate for about 2 sec. after you let go of the shutter button.
Basic Operation Power/Quick Control Dial Switch <2> : The camera is turned off and does not operate. Position for when you do not use the camera. <1> : The camera operates. : The camera and <5> operate. (p.34) Whenever you set the power switch to <1/J> or <2>, the sensor cleaning will be executed automatically. During the sensor cleaning, the LCD monitor will display a logo. To save battery power, the camera turns off automatically after about 1 minute of non-operation.
Basic Operation Pressing completely This releases the shutter and takes the picture. If you press the shutter button completely without pressing it halfway first or if you press the shutter button halfway and then press it completely immediately, the camera will take a moment before it takes the picture. Even during the menu display, image playback, and image recording, you can instantly go back to shooting-ready by pressing the shutter button halfway.
Basic Operation <5> Using the Quick Control Dial for Selecting Before using the <5> dial, set the power switch to . (1) After pressing a button, turn the <5> dial. When you press a button, its function remains selected for 6 seconds (9). During this time, you can turn the <5> dial to set the desired setting. When the function turns off or if you press the shutter button halfway, the camera will be ready to shoot.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lens E (10 types, sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake. Horizontal shooting Vertical shooting 1. Wrap your right hand around the camera grip firmly.
Menu Operations By setting various optional settings with the menus, you can set the image-recording quality, Picture Style, the date/time, Custom Functions, etc. While looking at the LCD monitor, you use the button on the camera back and the <6> <5> dials. button LCD monitor <6> Main Dial <5> Quick Control Dial <0> button Set-up Playback Shooting Custom Functions My Menu Tab Menu items Menu settings * The [2/7/8/9] tabs are not displayed in Basic Zone modes such as Full Auto.
Menu Operations Menu Setting Procedure 1 Display the menu. Press the button to display the menu. a tab. 2 Select Turn the <6> dial to select a tab. a menu item. 3 Select Turn the <5> dial to select the menu item, then press <0>. the setting. 4 Select Turn the <5> dial to select the desired setting. the desired setting. 5 SetPress <0> to set it. the menu. 6 ExitPress the button to exit the menu and return to camera shooting.
Menu Operations Menu Settings 1 Shooting 1 (Red) Page Quality 73 / 83 / 74 / 84 / 76 / 86 / 1 / D 1+(73 / 83 / 74 / 84 / 76 / 86) D + (73 / 83 / 74 / 84 / 76 / 86) Red-eye On/Off Off / On Beep On / Off – Shoot w/o card On / Off 29 Review time Off / 2 sec. / 4 sec. / 8 sec.
Menu Operations 4 Playback 2 (Blue) Page Highlight alert Disabled / Enable 117 AF point disp. Disabled / Enable 117 Histogram Brightness / RGB 118 Auto play Auto playback of images 121 Auto power off 1min. / 2 min. / 4 min. / 8 min. / 15 min. / 30 min. / Off 42 File numbering Continuous / Auto reset / Manual reset 72 Auto rotate On zD / On D / Off 126 INFO button Normal disp. / Camera set. / Shoot. func.
Menu Operations 7 Set-up 3 (Yellow) Page Camera user setting Register current camera settings to the Mode Dial’s , , or position 165 Clear all camera settings Resets the camera to the default settings 44 Firmware Ver. For updating the firmware – 8 Custom Functions (Orange) C.Fn I: Exposure 154 C.Fn II: Image C.Fn III: Auto focus/Drive 156 Customize the camera as desired 157 C.Fn IV: Operation/Others 160 Clear all Custom Func. Clears all Custom Function settings (C.
Before You Start 3 Setting the Interface Language 1 Select [Language]. Under the [6] tab, select [Language] (the third item from the top), then press <0>. the desired language. 2 SetTurn the <5> dial to select the language, then press <0>. X The language will change. 3 Setting the Date and Time Check if the camera’s date and time are set correctly. If necessary, set the correct date and time. 1 Select [Date/Time]. Under the [6] tab, select [Date/ Time], then press <0>.
Before You Start 3 Set the power-off time/Auto power off You can change this auto power-off time for the camera to turn off automatically after a certain period of non-operation. If you do not want the camera to turn off automatically, set this to [Off]. After the power turns off, you can turn on the camera again by pressing the shutter button or other button. 1 Select [Auto power off]. Under the [5] tab, select [Auto power off], then press <0>. the desired time.
Before You Start [OK]. 2 Select Turn the <5> dial to select [OK], then press <0>. X The CF card will be formatted (initialized). X When the formatting is completed, the menu will reappear. When the CF card is formatted or erased, only the file management information is changed. The actual data is not completely erased. Be aware of this when selling or discarding the card. When discarding the CF card, destroy the card physically to prevent personal data from being leaked.
3 Resetting Camera SettingsN The camera’s shooting settings and menu settings can be reset to the default settings. 1 Select [Clear all camera settings]. Under the [7] tab, select [Clear all camera settings], then press <0>. [OK]. 2 Select Turn the <5> dial to select [OK], then press <0>. X When [Clear all camera settings] is set, the camera will be reset to the following settings.
2 Basic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. With the Basic Zone modes, all you do is point and shoot and the camera sets everything automatically. (p.172) Also, to prevent botched pictures due to mistaken operations, camera settings cannot be changed in the Basic Zone modes. Full Auto Basic ne Zo Automatic image correction in Basic Zone modes In Basic Zone modes, the image is adjusted automatically to obtain the best brightness.
1 Fully Automatic Shooting AF point 1 Set the Mode Dial to <1>. any AF point over the 2 Aim subject. All the AF points will operate, and focus will generally be achieved at the AF point covering the closest object. Aiming the center AF point over the subject will make focusing easier. the subject. 3 Focus Press the shutter button halfway, and the lens will move to focus. X The AF point which achieves focus will briefly flash in red.
1 Fully Automatic Shooting FAQ The focus confirmation light blinks and focus is not achieved. Aim the AF point over an area having good contrast between light and dark, then press the shutter button halfway. (p.80) If you are too close to the subject, move away and try again. Sometimes multiple AF points flash simultaneously. This indicates that focus has been achieved at all those AF points. As long as the AF point covering the desired subject flashes, you can take the picture.
1 Full Auto Techniques Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the <1> (Full Auto) mode, while you press the shutter button halfway to focus a still subject, the focus will be locked. You can then recompose the shot and press the shutter button completely to take the picture. This is called focus lock. Focus lock is also possible in other Basic Zone modes (except <5>).
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes flesh tones and the hair look softer than with the <1> (Full Auto) mode. Shooting Tips The further the distance between the subject and background, the better. The further the distance between the subject and background, the more blurred the background will look. The subject will also stand out better in front of a plain, dark background. Use a telephoto lens.
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery, night scenes, and to have everything in focus from near to far. The greens and blues also become more vivid and sharp than with <1> (Full Auto). Shooting Tips With a zoom lens, use the wide-angle end. When using a zoom lens, use the wide-angle end. This will have objects near and far in focus, better than at the telephoto end. It also adds breadth to landscapes. Shooting night scenes.
4 Shooting Close-ups When you want to photograph flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips Use a simple background. A simple background makes the flower, etc., stand out better. Move to the subject as close as possible. Check the lens for its minimum focusing distance. Some lenses have indications such as <40.28m/0.9ft>.
5 Shooting Moving Subjects To photograph a moving subject whether it be a child running or an auto race, use the <5> (Sports) mode. Shooting Tips Use a telephoto lens. Using a telephoto lens is recommended so you can shoot from afar. Use the center AF point to focus. Aim the center AF point over the subject, then press the shutter button halfway to auto focus. During autofocusing, the beeper will continue beeping softly. If focus cannot be achieved, the focus confirmation light will blink.
6 Shooting Portraits at Night To shoot someone at night and obtain a natural-looking exposure in the background, use the <6> (Night Portrait) mode. Shooting Tips Use a wide-angle lens and a tripod. If you use a zoom lens, set it to the wide-angle end to obtain a wide night view. Use a tripod to prevent camera shake. Keep the person within 5 meters/16.4 feet from the camera. Under low light, the built-in flash will fire automatically to obtain a good exposure of the person.
7 Disabling Flash In places where flash photography is prohibited, use the <7> (Flash Off) mode. This mode is also effective for candlelight scenes when you want to obtain the candlelight effect. Shooting Tips If the numeric display in the viewfinder blinks, take care to prevent camera shake. Under low light when camera shake is prone to occur, the viewfinder’s shutter speed display will blink. Hold the camera steady or use a tripod.
3 Image Settings This chapter explains the digital image settings for the image-recording quality, ISO speed, Picture Style, white balance, and color space. In the Basic Zone modes, only the image-recording quality (except RAW/sRAW, RAW/sRAW+JPEG) and the file numbering method can be set as explained in this chapter. The asterisk M on the right of the page title indicates that the respective feature is available only in Creative Zone modes (d, s, f, a, 8).
3 Setting the Image-recording Quality Set the image-recording quality to suit the intended image size for printing, etc. In the Basic Zone modes, only the following imagerecording quality settings can be set: 73, 83, 74, 84, 76, 86. They are all JPEG images. In the 1/D modes, the image will require processing with the software provided. (p.58) 1 Select [Quality]. Under the [1] tab, select [Quality], then press <0>. X The image-recording quality screen will appear. the image-recording 2 Select quality.
3 Setting the Image-recording Quality Image File Size and CF Card Capacity According to Image-Recording Quality Quality 73 Maximum Burst (Approx.) File Size Possible Shots (Approx. MB) (Approx.) o High-speed i Low-speed 3.5 274 75 205 83 1.8 523 171 523 74 2.1 454 140 454 84 1.1 854 303 854 76 1.2 779 271 779 86 0.7 1451 625 1451 1 12.4 76 17 20 1+73 12.4 + 3.5 59 14 16 1+83 12.4 + 1.8 66 14 16 1+74 12.4 + 2.1 65 14 16 1+84 12.4 + 1.1 70 14 16 1+76 12.
3 Setting the Image-recording Quality About RAW The RAW image is the data output by the image sensor and converted to digital data which is recorded on the CF card as is. The RAW image is transferred to a personal computer where software (provided) is used to adjust the image as needed. From the RAW image, the software can develop and generate the adjusted image in the desired type such as JPEG or TIFF. About sRAW This is a small RAW image which is one-fourth (approx. 2.
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. For example, when you increase the ISO speed (higher number) for low light, a faster shutter speed can be used and camera shake will be less prone to occur. The effective range of the flash will also increase. ISO Speed in the Basic Zone Modes The ISO speed is set automatically within ISO 100 - 800. ISO Speed in the Creative Zone Modes ISO 100 - 1600 can be set in 1/3-stop increments.
i: Setting the ISO SpeedN About “Auto” ISO Speed If the ISO speed is set to “Auto”, the actual ISO speed to be set will be displayed when you press the shutter button halfway. As indicated below, the ISO speed will be set automatically to suit the shooting mode. Shooting Mode ISO Speed Setting 1, 3, 4, 6, 7 The ISO speed is set automatically within ISO 100 - 800. The ISO speed set automatically will vary depending on the shooting mode. The picture will be taken at the standard exposure.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain the desired image effects matching your photographic expression or the subject. In the Basic Zone modes, the Picture Style is set automatically, so the operation explained on this page to page 66 cannot be done. 1 Press the button. When the camera is ready to shoot, press the button. X The Picture Style screen will appear. a Picture Style. 2 Select Turn the <5> dial to select a Picture Style, then press <0>.
A Selecting a Picture StyleN Faithful The image is dull and subdued. When the subject is captured under a color temperature of 5200K, the color is adjusted colorimetrically to match the subject’s color. This Picture Style assumes that you will do post-processing with a personal computer. Monochrome For black-and-white images. To obtain natural-looking, black-and-white images, set a suitable white balance. The image cannot be reverted back to color except for 1 and D images.
A Customizing the Picture StyleN You can customize the Picture Style by adjusting the individual parameters like [Sharpness] and [Contrast]. To customize [Monochrome], see the next page. 1 Press the button. a Picture Style. 2 Select Turn the <5> dial to select a Picture Style, then press the button. a parameter. 3 Select Turn the <5> dial to select a parameter, then press <0>. the parameter. 4 SetTurn the <5> dial to set the parameter as desired, then press <0>.
A Customizing the Picture StyleN By selecting [Default set.] in step 3, you can revert the respective Picture Style to its default parameters. To shoot with the Picture Style you modified, follow step 2 on the preceding page to select the Picture Style and then shoot. Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast].
A Registering the Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create Picture Styles whose parameters such as sharpness and contrast are different. You can also select a Picture Style already set with the provided software. 1 Press the button. [User Def.]. 2 Select Turn the <5> dial to select [User Def. *], then press the button. <0>.
A Registering the Picture StyleN the parameter. 6 SetTurn the <5> dial to set the parameter as desired, then press <0>. Press the button to register the new Picture Style. The Picture Style selection screen will then reappear. X The base Picture Style will be displayed on the right of [User Def. *]. X The name of the Picture Style having any modified settings (different from the default) registered under [User Def. *] will be displayed in blue.
B: Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the (Auto) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with , you can set the white balance manually to suit the respective light source. In the Basic Zone modes, will be set automatically. 1 Press the button. (9) the white balance. 2 Select While looking at the LCD panel, turn the <5> dial. Icon Mode Q Auto Color Temperature (Approx.
B: Setting the White BalanceN O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. 1 Photograph a white object. The plain, white object should fill the spot metering circle. Focus manually and set the standard exposure for the white object. You can set any white balance. Spot metering circle [Custom WB]. 2 Select Under the [2] tab, select [Custom WB], then press <0>. X The SET screen will appear.
B: Setting the White BalanceN If the exposure obtained in step 1 is way off, a correct white balance might not be obtained. If the image was captured while the Picture Style was set to [Monochrome] (p.62), it cannot be selected in step 3. Instead of a white object, an 18% gray card (commercially available) can produce a more accurate white balance. The personal white balance registered with the provided software will be registered under .
3 White Balance CorrectionN You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. Users familiar with using color temperature conversion or color compensating filters will find this feature handy. White Balance Correction 1 Select [WB SHIFT/BKT]. Under the [2] tab, select [WB SHIFT/BKT], then press <0>.
3 White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images having a different color tone can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing (WB-BKT). White balance bracketing is possible up to ±3 levels in single-level increments. Set the white balance bracketing amount.
3 File Numbering Methods The file number is like the frame number on a roll of film. The captured images are assigned a sequential file number from 0001 to 9999 and saved in one folder. You can also change how the file number is assigned. The file number will appear on the personal computer in this format: IMG_0001.JPG. 1 Select [File numbering]. Under the [5] tab, select [File numbering], then press <0>. the file numbering method. 2 Select Turn the <5> dial to select the desired method, then press <0>.
3 File Numbering Methods Auto Reset Resets the file numbering to 0001 whenever the CF card is replaced Each time the CF card is replaced, the file numbering starts from 0001. This is convenient if you want to organize images according to CF cards. If the replacement CF card contains images recorded previously, the file numbering of the new images might continue from the file numbering of the existing images in the card. To start the file numbering from 0001, the CF card must be formatted before use.
3 Setting the Color SpaceN The color space refers to the range of reproducible colors. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal images, sRGB is recommended. 1 Select [Color space]. Under the [2] tab, select [Color space], then press <0>. the desired color space. 2 SetSelect [sRGB] or [Adobe RGB], then press <0>. About Adobe RGB This is mainly used for commercial printing and other industrial uses.
4 Setting the AF and Drive Modes The viewfinder has 9 AF points. By selecting a suitable AF point, you can shoot with autofocus while framing the subject as desired. You can also select the AF mode and drive mode best matching the shooting conditions and subject. The asterisk M on the right of the page title indicates that the respective feature is available only in Creative Zone modes (d, s, f, a, 8). In the Basic Zone modes, the AF mode, AF point selection, and drive mode are set automatically.
f: Selecting the AF ModeN Select the AF mode suiting the shooting conditions or subject. In the Basic Zone modes, the optimum AF mode is set automatically. 1 On the lens, set the focus mode switch to . the Mode Dial to a Creative 2 Set Zone mode. 3 Press the button. (9) the AF mode. 4 Select While looking at the LCD panel, turn the <6> dial. X: One-Shot AF 9: AI Focus AF Z: AI Servo AF One-Shot AF for Still Subjects Suited for still subjects.
f: Selecting the AF ModeN If focus cannot be achieved, the focus confirmation light in the viewfinder will blink. If this occurs, a picture cannot be taken even if the shutter button is pressed completely. Recompose the picture and try and focus again. Or see “When Autofocus Fails” (p.80). If the [1 Beep] menu is set to [Off], the beeper will not sound when focus is achieved. AI Servo AF for Moving Subjects This AF mode is for moving subjects when the focusing distance keeps changing.
S Selecting the AF PointN Select one of the nine AF points to autofocus. In the Basic Zone and <8> modes, automatic AF point selection will take effect automatically. You cannot select the AF point. 1 Press the button. (9) X The selected AF point will be displayed in the viewfinder and on the LCD panel. If all the AF points light in the viewfinder, it means automatic AF point selection is in effect. the AF point. 2 Select To select an AF point, you can either turn the <6> or <5> dial or use <9>.
S Selecting the AF PointN When looking at the LCD panel to select the AF point, note the following: Automatic selection right , center , , top If focus cannot be achieved with the external, EOS-dedicated Speedlite’s AF-assist beam, select the center AF point. AF-Assist Beam with the Built-in Flash Under low-light conditions, when you press the shutter button halfway, the built-in flash fires a brief burst of flashes. It illuminates the subject to enable easier autofocusing.
When Autofocus Fails Autofocus can fail to achieve focus (the focus confirmation light blinks) with certain subjects such as the following: Subjects difficult to focus Low-contrast subjects Example: Blue sky, solid-color walls, etc. Subjects in low light Extremely backlit and reflective subjects Example: Car with a reflective body, etc. Overlapping near and far objects Example: Animal in a cage, etc. Repetitive patterns Example: Skyscraper windows, computer keyboards, etc.
i Selecting the Drive ModeN Single and continuous drive modes are provided. In the Basic Zone modes, the optimum drive mode is set automatically. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel, turn the <5> dial. u : Single shooting When you press the shutter button completely, one shot will be taken. o: High-speed continuous shooting (Max. 6.5 shots per sec.) i : Low-speed continuous shooting (Max. 3 shots per sec.
j Self-timer Operation Use the self-timer when you want to be in the picture. The (10 sec. timer) can be used in all shooting modes. 1 Press the button. (9) either or . 2 Select Look at the LCD panel and turn the <5> dial to select or . j : 10-sec. self-timer l : 2-sec. self-timer N the picture. 3 TakeFocus the subject and press the shutter button completely. X The picture will be taken after the self-timer delay elapses.
5 Advanced Operations Cre ati v e ne Zo With Creative Zone modes, you can set the desired shutter speed or aperture to obtain the result you want. You take control of the camera. The asterisk M on the right of the page title indicates that the respective feature is available only in Creative Zone modes (d, s, f, a, 8). After you press the shutter button halfway and let go, the LCD panel and viewfinder information will remain displayed for about 4 sec. (0).
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . the subject. 2 Focus Look through the viewfinder and aim the selected AF point over the subject. Then press the shutter button halfway. X The AF point which achieves focus flashes in red, and the focus confirmation light in the viewfinder’s bottom right lights.
d: Program AE If “30"” shutter speed and the maximum aperture blink, it indicates underexposure. Increase the ISO speed or use flash. If “8000” shutter speed and the minimum aperture blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and <1> (Full Auto) With <1>, many functions such the AF mode, drive mode, and built-in flash are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the correct exposure matching the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or moving subject. Or a slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Fast shutter speed 1 Slow shutter speed Set the Mode Dial to . the desired shutter speed.
s: Shutter-Priority AE If the maximum aperture blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the minimum aperture blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the correct exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/ number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/ number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (smaller f/ number) until the blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (larger f/ number) until the blinking stops or set a lower ISO speed. Aperture Display The larger the f/number, the smaller the aperture opening will be.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available handheld exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . the shutter speed and 2 Set aperture. To set the shutter speed, turn the <6> dial. To set the aperture, set the power switch to , and turn the <5> dial.
8: Automatic Depth-of-Field AE Objects in the foreground and background will be in focus automatically. All the AF points will function to detect the subject, and the aperture required to attain the necessary depth of field will be set automatically. * <8> stands for Auto-Depth of field. This mode sets the depth of field automatically. 1 Set the Mode Dial to <8>. the subject. 2 Focus Aim the AF points over the subjects and press the shutter button halfway.
q Selecting the Metering ModeN Four metering modes are provided: Evaluative, partial, spot, and center-weighted average metering. In the Basic Zone modes, evaluative metering is set automatically. 1 Press the button. (9) the metering mode. 2 Select While looking at the LCD panel, turn the <6> dial. q: Evaluative metering w: Partial metering r: Spot metering e: Center-weighted average metering q Evaluative metering This is an all-around metering mode suited for portraits and even backlit subjects.
Setting Exposure CompensationN Exposure compensation is used to alter the standard exposure set by the camera. You can make the image look brighter (increased exposure) or darker (decreased exposure). You can set the exposure compensation up to ±2 stops in 1/3-stop increments. the Mode Dial to any 1 Turn Creative Zone mode except . the exposure level 2 Check indicator. Press the shutter button halfway and check the exposure level indicator.
3 Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±2 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [AEB]. Under the [2] tab, select [AEB], then press <0>. the AEB amount. 2 SetTurn the <5> dial to set the AEB amount, then press <0>. X When you exit the menu, and the AEB level will be displayed on the LCD panel. AEB amount the picture.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the shot. This is called AE lock. It is effective for backlit subjects. 1 Focus the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button.
Bulb Exposures When bulb is set, the shutter stays open while you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. 1 Set the Mode Dial to . the shutter speed to “buLb.” 2 SetWhile looking at the LCD panel, turn the <6> dial to select “buLb.” The next setting after “30"” is “buLb.” aperture and shoot.
Bulb Exposures Using the Eyepiece Cover If you take a picture without looking at the viewfinder, light entering the eyepiece can throw off the exposure. To prevent this, use the eyepiece cover attached to the camera strap. 1 Remove the eyecup. From the bottom of the eyecup, push it upward. the Eyepiece Cover. 2 Attaching Slide the eyepiece cover down into the eyepiece groove to attach it.
Mirror LockupN Although using the self-timer or Remote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations can also help when you use a super telephoto lens or shoot close ups. When [8C.Fn III -7] (Mirror lockup) is set to [1:Enable] (p.160), shooting with mirror lockup will be possible. 1 Focus the subject, press the shutter button completely and release it. X The mirror will swing up. 2 Press the shutter button completely again.
Using the Built-in Flash E-TTL II autoflash obtains high-precision and consistent flash shots. Using the Built-in Flash in the Basic Zone If necessary, the built-in flash will pop-up automatically in low-light or backlit conditions. (except in <3> <5> <7> modes) Using the Built-in Flash in the Creative Zone Regardless of the light level, you can press the button to pop-up and fire the built-in flash whenever desired. If the built-in flash has popped up, you can push it back down with your fingers.
Using the Built-in Flash Effective Range of Built-in Flash ISO Speed EF-S18-55mm f/3.5-5.6 IS Wide Angle: 18mm Telephoto: 55mm [Approx. meters/feet] EF-S17-85mm f/4-5.6 IS USM Wide Angle: 17mm Telephoto: 85mm 100 1 - 3.7 / 3.3 - 12.1 1 - 2.3 / 3.3 - 7.5 1 - 3.3 / 3.3 - 10.8 1 - 2.3 / 3.3 - 7.5 200 1 - 5.3 / 3.3 - 17.4 1 - 3.3 / 3.3 - 10.8 1 - 4.6 / 3.3 - 15.1 1 - 3.3 / 3.3 - 10.8 400 1 - 7.4 / 3.3 - 24.3 1 - 4.6 / 3.3 - 15.1 1 - 6.5 / 3.3 - 21.3 1 - 4.6 / 3.3 - 15.1 800 1 - 10.5 / 3.3 - 34.
Using the Built-in Flash y Flash Exposure CompensationN In the same way as normal exposure compensation, you can set exposure compensation for flash. You can set flash exposure compensation up to ±2 stops in 1/3-stop increments. 1 Increased exposure Decreased exposure Press the button. (9) the flash exposure 2 Set compensation amount. While looking at the LCD panel or viewfinder, turn the <5> dial. To cancel the flash exposure compensation, set the flash exposure compensation amount back to .
Using the Built-in Flash A FE LockN FE (flash exposure) lock obtains and locks the correct flash exposure reading for any part of a subject. 1 Press the button to pop-up the built-in flash. Press the shutter button halfway and look in the viewfinder to check that the icon is lit. 2 Focus the subject. the button. (8) 3 Press Aim the viewfinder center over the subject where you want to lock the flash exposure, then press the button.
3 Flash ControlN The built-in flash and external Speedlite can also be set with the menu. The menu for the external Speedlite will be applicable only to EX-series Speedlites whose functions can be set with the camera. Select [Flash control]. Under the [6] tab, select [Flash control], then press <0>. X The flash control screen will appear. [Flash firing] Normally, set this to [Enable]. If [Disable] is set, both the built-in flash and external Speedlite will not fire.
3 Flash ControlN E-TTL II For normal flash exposures, set it to [Evaluative]. If [Average] is set, the flash exposure will be averaged for the entire metered scene as with an external metering flash. Flash exposure compensation may be necessary depending on the scene, so this is for advanced users. Setting the External Speedlites Select either [External flash func. setting] or [External flash C.Fn setting].
External Speedlites EOS-dedicated, EX-series Speedlites Basically operates like a built-in flash for easy operation. When an EX-series Speedlite is attached to the camera, almost all the autoflash control is done by the camera. In other words, it is like a highoutput flash attached externally in place of the built-in flash. For detailed instructions, see the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites.
External Speedlites Using Non-Canon Flash Units Sync Speed The camera can synchronize with compact, non-Canon flash units at 1/ 250 sec. or slower shutter speeds. With large studio flash, the sync speed is 1/60 sec. or slower. Be sure to test the flash unit beforehand to make sure it synchronizes properly with the camera. PC Terminal The camera’s PC terminal is provided for flash units having a sync cord. The PC terminal is threaded to prevent inadvertent disconnection.
6 Live View Shooting You can shoot while viewing a real-time image on the camera’s LCD monitor or on a personal computer screen. This is called “Live View shooting.” When using Live View shooting, using a hard disk-type CF card (such as MicroDrive) is not recommended. If Live View shooting is done under direct sunlight or other hightemperature environments, the < > icon (warning for high temperature in the camera) may appear on the screen.
Live View ShootingN Instead of looking through the viewfinder, you can look at a real-time image on the camera’s LCD monitor while shooting. Live View shooting does not work in Basic Zone modes. Preparing for Live View Shooting the lens focus mode switch to 1 Set . mode. 2 SetSetthetheshooting shooting mode to a Creative Zone mode. [Live View function 3 Select settings]. Under the [6] tab, select [Live View function settings], then press <0>. [Live View shoot.].
Live View ShootingN Displaying Live View Image on the LCD Monitor With the camera ready to shoot, press <0>. X The Live View image will appear on the LCD monitor in real-time with approx. 100% field of view. With the video cable (provided) connecting the camera to a TV set, you can view images on the TV. (p.122) During Live View image display, if you point the camera in a different direction, it might throw off the correct brightness momentarily and the image might not look right.
Live View ShootingN Magnifying the Image for Manual Focusing 1 Move the focusing frame to the position where you want to focus. Use <9> to move the focusing frame in full view. If you press <9> straight down, the focusing frame will return to the center. the button. 2 Press X The focusing frame will be magnified. Magnification: Approx. 10x X AE lock will be applied to the full-view exposure, and the shutter speed and aperture settings will be displayed in orange.
Live View ShootingN Taking the picture 1 Check the composition. Press the button to check the image composition in full view. the shutter speed and 2 Check aperture display. the picture. 3 TakePress the shutter button completely. X The picture will be taken and the captured image is displayed on the LCD monitor. X After the image review ends, the camera will return to Live View shooting automatically. To terminate shooting, press <0> while Live View image is displayed.
Live View ShootingN About the Information Display Each time you press the button, the information display will change. Histogram (Brightness/ RGB) Focusing frame Live View exposure simulation (C.
Live View ShootingN About Silent Shooting Instructions for setting the [6 Live View function settings] menu’s [Silent shoot.] are explained below. Mode 1 The shooting sound will be quieter than when Live View shooting is not used. Continuous shooting is also possible. For high-speed continuous shooting, it will be approx. 6 fps. Mode 2 When you press the shutter button completely, only one shot will be taken. While you keep holding down the shutter button, further camera operation will be suspended.
Live View ShootingN Using AF to Focus If the [8C.Fn III -6] (AF during Live View shooting) setting is set to [Enable], you can focus with the
button. Be sure to set the lens focus mode switch to , set the AF mode to , and select the center AF point. <0> to the display Live 1 Press View image. the subject. 2 Focus Cover the subject with the focusing frame and press the button. X The Live View image will turn off, the reflex mirror will go back down, and AF will be executed.
7 Image Playback This chapter explains how to playback images, including how to erase images and how to display images on a TV screen. For images taken with another camera: The camera might not be able to properly display images captured with a different camera or edited with a personal computer or whose file name was changed.
x Image Playback Single Image Display 1 Playback the image. Press the button. X The last captured image or last image viewed will appear. the image. 2 Select To playback images starting with the last image, turn the <5> dial counterclockwise. To playback images starting with the first captured image, turn the dial clockwise. Press the button to change the display format.
x Image Playback Shooting Information Display Exposure compensation amount Protect Flash exposure compensation amount Folder number - File number CF card Aperture Histogram (Brightness/RGB) Shutter speed Picture Style settings Metering mode Shooting mode ISO speed Color temperature if
is set Image-recording quality Color space Date and time File number/ Total images recorded Original decision (image verification) data appended White balance White balance correction File size About the H
x Image Playback About the Histogram The brightness histogram display shows the exposure level distribution, overall brightness, and gradation. And the RGB histogram display is for checking the color saturation and gradation. The display can be switched with the [4 Histogram] menu. [Brightness] Display Sample Histograms This histogram is a graph showing the distribution of the image’s brightness level.
x Image Playback Index Display 1 Turn on the index display. During image playback, press the button. X The 4-image index display will appear. The currently-selected image will be highlighted in a blue frame. Press the button again to switch to the 9-image index display. the image. 2 Select Turn the <5> dial to move the blue frame. To display an image, press the button. I Jump Display You can skip over images during playback to find the image you want faster.
x Image Playback u/y Magnified View Magnify the image. During image playback, press the button to magnify the image. If you keep pressing the button, you can magnify the image up to 10x. Press the button to reduce the magnification. Use <9> to scroll around the magnified image. Magnified area You can turn the <6> or <5> dial to view another image. Magnified view is not possible during the image review immediately after the image is taken. b Rotating an Image 1 Select [Rotate].
x Image Playback 3 Auto Playback You can playback the CF card’s images in an automatic slide show. Each image will be displayed for about 4 sec. 1 Select [Auto play]. Under the [4] tab, select [Auto play], then press <0>. X The auto play screen will appear. the auto play. 2 Start X After [Loading image...] is displayed Ð for a few seconds, auto play will start. To pause the auto play, press <0>. During pause, [ ] will be displayed on the upper left of the image.
x Image Playback Viewing the Images on TV By connecting the camera to a TV set with the video cable (provided), you can view the captured images on a TV set. Turn off the camera and the television before connecting them. 1 Connect the camera to the TV. Open the camera’s terminal cover. Use the video cable (provided) to connect the camera’s video OUT terminal to the TV monitor’s VIDEO IN terminal. Insert the video cable plugs firmly all the way.
3 Protecting Images This prevents the image from being erased accidentally. 1 Image protect Select [Protect images]. Under the [3] tab, select [Protect images], then press <0>. X The protect setting screen will appear. the image. 2 Protect Turn the <5> dial to select the image to be protected, then press <0>. X When an image is protected, the icon will appear on the screen. To cancel the image protection, press <0> again. The icon will disappear. To protect another image, repeat step 2.
L Erasing Images You can either select and erase images one by one or erase them in one batch. Protected images (p.123) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a Single Image 1 Playback the image to be erased. the button. 2 Press The erase menu will appear at the bottom of the screen. the image.
Changing Image Playback Settings 3 Setting the LCD Monitor Brightness You can adjust the brightness of the LCD monitor to make it easier to read. 1 Select [LCD brightness]. Under the [6] tab, select [LCD brightness], then press <0>. the brightness. 2 Adjust While referring to the gray chart, turn the <5> dial, then press <0>. To check the image’s exposure, you should look at the histogram (p.118).
Changing Image Playback Settings 3 Auto Rotate of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and personal computer instead of horizontally. The setting of this feature can be changed. 1 Select [Auto rotate]. Under the [5] tab, select [Auto rotate], then press <0>. the auto rotate display. 2 SetTurn the <5> dial to select the setting, then press <0>.
8 Sensor Cleaning The camera has a Self Cleaning Sensor Unit attached to the sensor’s front layer (low-pass filter) to shake off dust automatically. The Dust Delete Data can also be appended to the image so that the remaining dust spots can be removed automatically by Digital Photo Professional (provided software). Minimizing Dust When changing lenses, do it in a place with minimal dust. When storing the camera without a lens attached, be sure to attach the body cap to the camera.
3 Automatic Sensor Cleaning Whenever you set the power switch to <1/J> or <2>, the Self Cleaning Sensor Unit operates (approx. 1 sec.) to automatically shake off the dust on the front of the sensor. Normally, you need not be aware of this operation. However, you can execute the sensor cleaning at anytime as well as disable it. Cleaning the Sensor Now 1 Select [Sensor cleaning]. Under the [6] tab, select [Sensor cleaning], then press <0>. [Clean nowf].
3 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image to later erase the dust spots. The Dust Delete Data is used by Digital Photo Professional (provided software) to erase the dust spots automatically. Preparation Get a solid-white object (paper, etc.). Set the lens focal length to 50mm or longer.
3 Appending Dust Delete DataN a solid-white object. 3 Photograph At a distance of 20 - 30 cm / 0.7 - 1.0 feet, fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in the aperture-priority AE mode with an aperture of f/22. Since the image will not be saved, the data can still be obtained even if there is no CF card in the camera. X When the picture is taken, the data will be obtained. When the data is obtained, a message will appear.
3 Manual Sensor CleaningN Dust which could not be removed by the automatic sensor cleaning can be removed manually with a blower, etc. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. Before cleaning the sensor, detach the lens from the camera. 1 Select [Sensor cleaning]. Under the [6] tab, select [Sensor cleaning], then press <0>. [Clean manually].
3 Manual Sensor CleaningN While cleaning the sensor, never do any of the following. If the power is cut off, the shutter will close and the shutter curtains and image sensor might get damaged. • Setting the power switch to <2>. • Opening the battery compartment cover. • Opening the CF card slot cover. The surface of the image sensor is extremely delicate. Clean the sensor with care. Use a plain blower without any brush attached. A brush can scratch the sensor.
9 Direct Printing from the Camera/ Digital Print Order Format You can connect the camera directly to a printer and print out the images in the CF card. The camera is compatible with “wPictBridge” which is the standard for direct printing. You can also preselect images in the CF card for printing. (p.143) About DPOF DPOF (Digital Print Order Format) is a standard for recording printing instructions (image selections, quantity to print, etc.) in the CF card.
Preparing to Print You do the direct printing procedure entirely with your camera while you look at the LCD monitor. Connecting the Camera to a Printer 1 Set the camera’s power switch to <2>. the printer. 2 SetForupdetails, see the printer’s instruction manual. the camera to the 3 Connect printer. Use the interface cable that came with the camera. When connecting the cable plug to the camera’s terminal, the cable plug’s icon must face the front side of the camera.
Preparing to Print wPictBridge the image. 6 Playback Press the button. X The image will appear, and the icon will appear on the upper left to indicate that the camera is connected to a printer. X The button lamp will light in blue. The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct. When connecting the camera to the printer, do not use any cable other than the interface cable provided.
wPrinting The screen display and setting options will differ depending on the printer. Some settings might not be available. For details, see the printer’s instruction manual. Printer-connected icon 1 Select the image to be printed. Check that the icon is displayed on the upper left of the LCD monitor. Turn the <5> dial to select the image to be printed. <0>. 2 Press X The print setting screen will appear. Print setting screen Sets the printing effects. (p.
wPrinting QSetting the Paper Size Turn the <5> dial to select the size of the paper loaded in the printer, then press <0>. X The paper type screen will appear. YSetting the Paper Type Turn the <5> dial to select the type of the paper loaded in the printer, then press <0>. When using a Canon printer and Canon paper, read the printer’s instruction manual to check what paper types can be used. X The page layout screen will appear.
wPrinting effects. 4 SetSettheasprinting necessary. Turn the <5> dial to select the item on the upper right, then press <0>. If the icon is displayed next to , the printing effects can also be adjusted. (p.140) Next, turn the <5> dial to select the desired printing effect, then press <0>. Item Description Same as the printing characteristics turned “On”. No automatic EOff correction will be performed. The image will be printed according to the printer’s standard colors.
wPrinting the date and file number 5 Set imprinting. Set as necessary. Turn the <5> dial to select , then press <0>. Turn the <5> dial to select the desired setting, then press <0>. of copies. 6 SetSettheasnumber necessary. Turn the <5> dial to select , then press <0>. Turn the <5> dial to select the number of copies, then press <0>. 7 StartTurnprinting. the <5> dial to select [Print], then press <0>. X The button’s blue lamp will blink and the printing will start.
wPrinting e Adjustment of Printing Effects In step 4 on page 138, select the printing effect. When the icon is displayed next to , press the button. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4. Brightness The image brightness can be adjusted. Adjust levels When you select [Manual], you can change the histogram’s distribution and adjust the image’s brightness and contrast.
wPrinting Trimming the Image You can crop the image and print only the trimmed portion as if the image was recomposed. Do the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again. 1 On the print setting screen, select [Trimming]. 2 Set the trimming frame size, position, and proportion. The image area within the trimming frame will be printed. The shape of the trimming frame can be changed with [Paper settings].
wPrinting Depending on the printer, the trimmed image area might not be printed as you specified. The smaller you make the trimming frame, the grainier the picture will look on the print. If the picture will be too grainy, the trimming frame will turn red. While trimming the image, look at the camera’s LCD monitor. If you look at the image on a TV screen, the trimming frame might not be displayed accurately. Handling Printer Errors If you resolve a printer error (no ink, no paper, etc.
W Digital Print Order Format (DPOF) Set the print type, date imprinting, and file No. imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) Setting the Printing Options 1 Select [Print order]. X Under the [3] tab, select [Print order], then press <0>. [Set up]. 2 Select Turn the <5> dial to select [Set up], then press <0>. as desired. 3 SetSetthetheoptions [Print type], [Date], and [File No.].
W Digital Print Order Format (DPOF) Print type K Standard Prints one image on one sheet. L Index Multiple, thumbnail images are printed on one sheet. K L Both Prints both the standard and index prints. On Date Off File No. On Off [On] imprints the recorded date on the print. [On] imprints the file No. on the print. 4 Exit the setting. Press the <7> button. X The print order screen will reappear. Next, select [Sel.Image] or [All image] to order the images to be printed.
W Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. Press the button to display the three-image view. To return to the singleimage display, press the button. After completing the print order, press the button to save the print order to the CF card. Quantity Total images selected Check mark Index icon [Standard] [Both] Press <0> and a print order for 1 copy of the displayed image will be placed.
W Direct Printing with DPOF With a PictBridge printer, you can easily print images with DPOF. 1 Prepare to print. See page 134. Follow the “Connecting the Camera to a Printer” procedure up to step 5. 2 Under the [3] tab, select [Print order]. 3 Select [Print]. [Print] will be displayed only if the camera is connected to the printer and printing is possible. 4 Set the [Paper settings]. (p.136) Set the printing effects (p.138) as necessary. 5 Select [OK]. Before printing, be sure to set the paper size.
10 Transferring Images to a Personal Computer You can use the camera to select images in the CF card and transfer them directly to a personal computer. If the computer software (EOS DIGITAL Solution Disk CD-ROM) provided with the camera has been installed in your personal computer, you can easily transfer the images without operating the personal computer. For instructions to install the provided software, see the separate sheet, “CD-ROM Guide.
d Transferring Images to a Personal Computer Before connecting the camera to the personal computer, be sure to first install the EOS DIGITAL Solution Disk software (in the CD-ROM provided with the camera) in the personal computer. Preparation for Image Transfer 1 Connect the camera to the personal computer. Turn off the camera and use the interface cable that came with the camera.
d Transferring Images to a Personal Computer Transferring Images to a Personal Computer The images transferred to the personal computer will be organized according to the shooting date and saved in the [My Pictures] folder for Windows or the [Pictures] folder in the Macintosh. Select the desired option, then press the button. The button’s blue lamp will blink and the image transfer will begin. When the image transfer is completed, the blue lamp will stay lit.
d Transferring Images to a Personal Computer 3 Selecting the Images to be Transferred Under the [3] tab, you can use [Transfer order] to select the images to be transferred to a personal computer. When you select [Transfer order images] on the preceding page, you can transfer the images set by the transfer order. Sel.Image Select and order images one by one. Press <0> to include the displayed image in the transfer order. The icon will also appear on the upper left.
11 Customizing the Camera With Custom Functions, you can change the camera functions according to your preference. Also, the current camera settings can be saved under the Mode Dial’s , , and positions. The functions explained in this chapter apply to Creative Zone modes.
3 Setting Custom FunctionsN 1 Select [8]. Turn the <6> dial to select the [8] tab. the group. 2 Select Turn the <5> dial to select C.Fn I IV, then press <0>. Custom Function No. 3 Select the Custom Function No. 4 Change the setting as desired. Turn the <5> dial to select the Custom Function No., then press <0>. Turn the <5> dial to select the setting (number), then press <0>. Repeat steps 2 to 4 if you want to set other Custom Functions.
3 Setting Custom FunctionsN Custom Functions C.Fn I: Exposure 1 2 3 4 5 6 7 Exposure level increments ISO speed setting increments ISO expansion Bracketing auto cancel Bracketing sequence Safety shift Flash sync. speed in Av mode C.Fn II: Image 1 2 3 Long exposure noise reduction High ISO speed noise reduction Highlight tone priority C.
3 Custom Function SettingsN Custom Functions are organized into four groups based on the function type: C.Fn I: Exposure, C.Fn II: Image, C.Fn III: Auto focus/Drive, C.Fn IV: Operation/Others. C.Fn I: Exposure C.Fn I -1 Exposure level increments 0: 1/3-stop 1: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, etc. Effective when you prefer to control the exposure in less fine increments than 1/3-stop increments.
3 Custom Function SettingsN C.Fn I -4 Bracketing auto cancel 0: On The AEB and WB-BKT settings will be canceled if you set the power switch to <2> or clear the camera settings. AEB will also be canceled when the flash is ready to fire. 1: Off The AEB and WB-BKT settings will be retained even when the power switch is set to <2>. (When the flash is ready, AEB will be canceled. However, the AEB amount will be retained in memory.) C.
3 Custom Function SettingsN C.Fn II: Image C.Fn II -1 Long exposure noise reduction 0: Off 1: Auto For 1 sec. or longer exposures, noise reduction is performed automatically if noise typical of long exposures is detected. This [Auto] setting is effective in most cases. 2: On Noise reduction is performed for all exposures 1 sec. or longer. The [On] setting may be effective for noise that cannot be detected or reduced with the [Auto] setting.
3 Custom Function SettingsN C.Fn II -3 Highlight tone priority 0: Disable 1: Enable Improves the highlight detail. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. With setting 1, noise in the shadow areas may be slightly more than usual. With setting 1, the settable ISO speed range will be 200 - 1600.
3 Custom Function SettingsN C.Fn III -2 Lens AF stop button function 0: AF stop 1: AF start AF operates only while the button is pressed. While the button is pressed, AF operation with the camera is disabled. 2: AE lock When the button is pressed, AE lock is applied. Convenient when you want to focus and meter at different parts of the picture.
3 Custom Function SettingsN C.Fn III -3 AF point selection method 0: Normal Press the button and use <9> to select the AF point. 1: Multi-controller direct Without pressing the button first, you can just use the <9> to select the desired AF point. Pressing the button will set it to automatic AF point selection. 2: Quick Control Dial direct Without pressing the button first, you can just use the <5> to select the desired AF point.
3 Custom Function SettingsN C.Fn III -6 AF during Live View shooting 0: Disable 1: Enable During Live View shooting, you can interrupt the Live View image display and focus for as long as you hold down the
button. C.Fn III -7 Mirror lockup Prevents camera vibrations caused by the reflex mirror action which can disturb shooting with super telephoto lenses or close-up shooting. See page 98 for the mirror lockup procedure. 0: Disable 1: Enable C.Fn IV: Operation/Others C.
3 Custom Function SettingsN C.Fn IV -2 AF-ON/AE lock button switch 0: Disable 1: Enable The functions of the
and buttons will be switched with each other’s function. When set to 1, press the button to display the image index or to reduce the image display. C.Fn IV -3 SET button when shooting You can assign a frequently-used function to <0>. When the camera is ready to shoot, you can press <0>.
3 Custom Function SettingsN C.Fn IV -5 Focusing Screen The camera provides interchangeable focusing screens. This Custom Function must be set so that the exposure correction matches the respective focusing screen. 0: Ef-A 1: Ef-D 2: Ef-S About focusing screen characteristics Ef-A: Standard Precision Matte Standard focusing screen that comes with the camera. Provides good viewfinder brightness and enables easy manual focusing. Ef-D: Precision Matte with grid This is the Ef-A with a grid.
3 Custom Function SettingsN C.Fn IV -6 Add original decision data 0: Off 1: On Data for verifying whether the image is original or not is appended to the image automatically. When the shooting information of an image appended with the verification data is displayed (p.117), the icon will appear. To verify whether the image is original, the Original Data Security Kit OSK-E3 (sold separately) is required. C.
3 Registering My MenuN For faster access, you can register up to six menus and Custom Functions which you change frequently. 1 Select [My Menu settings]. Under the [9] tab, select [My Menu settings], then press <0>. [Register]. 2 Select Turn the <5> dial to select [Register], then press <0>. the desired items. 3 Register Turn the <5> dial to select an item, then press <0>. When the confirmation dialog appears and you select [OK] and press <0>, the item will be registered.
3 Register Camera User SettingsN Under the Mode Dial’s , , and positions, you can register most of the current camera settings containing your preferred shooting mode, menus, Custom Function settings, etc. 1 Select [Camera user setting]. Under the [7] tab, select [Camera user setting], then press <0>. 2 Select [Register]. the camera user setting. 3 Register Turn the <5> dial to select the Mode Dial position where the camera settings will be registered, then press <0>.
12 Reference This chapter provides reference information for camera features, system accessories, etc. The back of this chapter also has an index to make it easier to look up things.
B Checking Camera Settings When the camera is ready to shoot, press the button and “Camera set.” and “Shoot. func.” will appear. When “Shoot. func.” is displayed, you can set the ISO speed and other shooting functions while looking at the LCD monitor. Display “Camera set.” and “Shoot. func.” Press the button. X The button toggles between the two screens. Display one of them. On the [5 INFO button] menu, you can either display [Camera set.] or [Shoot. func.]. Camera Settings (p.61, 62) (p.74) (p.
B Checking Camera Settings Shooting Functions AE lock Aperture Shutter speed Built-in flash recycling (BUSY) Shooting mode Exposure level indicator Picture Style Image-recording quality White balance Metering mode Flash-ready FE lock High-speed sync Battery check ISO speed Flash exposure compensation Drive mode Possible Shots AF mode Maximum burst Time If you press the , , , or button, the setting screen will appear and you can turn the <6> or <5> dial to set it.
Using a Household Power Outlet With AC Adapter Kit ACK-E2 (sold separately), you can connect the camera to a household power outlet and not worry about the battery level. 1 Connect the DC plug. Connect the DC Coupler’s plug to the AC adapter’s socket. the power cord. 2 Connect Connect the power cord to the AC adapter. Insert the prongs into a power outlet. When you are finished, disconnect the plug from the power outlet. the cord in the groove.
Replacing the Date/Time Battery The date/time (back-up) battery maintains the camera’s date and time. Its service life is about 5 years. If the date/time is reset when the battery is replaced, replace the back-up battery with a new CR2016 lithium battery as described below. The date/time setting will also be reset, so be sure to set the correct date/time. 1 Set the power switch to <2>. 2 Remove the battery. 3 Take off the battery holder. (+) (–) the battery.
Function Availability Table o: Set automatically k: User selectable Basic Zone Mode Dial Quality ISO speed 1 2 3 4 5 6 7 d k k k k k k k k k k k k RAW k k k k k RAW + JPEG k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k Neutral k k k k k Faithful k k k k k Monochrome k k k k k User Defined k k k k k k k k k k k k k k k k k k k k Preset WB k k k k k Custom WB k k k k k Color temperature s
Function Availability Table o: Set automatically k: User selectable Basic Zone Mode Dial : Not selectable Creative Zone Metering mode 1 2 3 4 5 6 7 d o o o o o o o k k k k k Partial k k k k k Spot k k k k k Center-weighted average k k k k k Program shift k Evaluative s f a 8 Exposure Exposure compensation k k k AEB k k k AE lock k k k Depth-of-field preview k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k
Troubleshooting Guide If there is a problem, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power The battery cannot be recharged with the battery charger provided. Do not recharge any battery pack other than Battery Pack BP-511A, BP-514, BP-511, or BP-512. The camera does not operate even when the power switch is set to <1>. The battery is not properly installed in the camera. (p.
Troubleshooting Guide Shooting No images can be shot or recorded. The CF card is not properly inserted. (p.28) If the CF card is full, replace the card or delete unnecessary images to make room. (p.28, 124) If you try to focus in the One-Shot AF mode while the focus confirmation light in the viewfinder blinks, a picture cannot be taken. Press the shutter button halfway again to focus, or focus manually. (p.32, 80) The LCD monitor does not display a clear image.
Troubleshooting Guide Live View shooting is not possible. When using Live View shooting, use a CF card (a hard disk-type CF card such as MicroDrive is not recommended). A hard disk-type CF card requires a lower temperature range for operation than with normal CF cards. If the temperature gets too high, the Live View shooting may stop temporarily to prevent damage to the card’s hard disk. When the camera’s internal temperature decreases, the Live View shooting will be able to resume. (p.
Error Codes Error code Countermeasures If there is a problem with the camera, an error message appears. Follow the onscreen instructions. To recover from the error screen, turn the power switch off and on, or remove and reinstall the battery. If error 02 (CF card problem) is displayed, remove and reinstall the CF card or format the card. This may resolve the problem. If the same error keeps appearing, there may be a problem. Write down the error code and consult your nearest Canon Service Center.
System Map Eyepiece Extender EP-EX15 ST-E2 Rubber Frame Eb E-series Dioptric Adjustment Lenses 220EX Bundled Accessories 430EX 580EX II Macro Ring Lite MR-14EX Macro Twin Lite MT-24EX Focusing Screen Ef-A Eyecup Eb Wide Strap EW-100DGR Angle Finder C Focusing Screen Ef-D Ef-S Battery Charger CG-580 or CB-5L Battery Pack BP-511A, BP-514 Battery Grip BG-E2N Battery Magazine BGM-E2 178 Battery Pack BP-511A AC Adapter DC Coupler AC-E2 DR-400 AC Adapter Kit ACK-E2 Car Battery Cable CB-570
System Map Timer Remote Controller TC-80N3 Remote Switch RS-80N3 Wireless Controller LC-5 EF-S lenses EF lenses TV/Video Wireless File Transmitter WFT-E3/WFT-E3A Video Cable VC-100 USB external media EOS DIGITAL Software Instruction Solution Disk Manual USB GPS unit Wireless LAN access point Interface Cable IFC-200U Wireless LAN adapter Ethernet port Interface Cable IFC-500U USB port Original Data Security Kit OSK-E3 CF card Card reader PC card slot PCMCIA adapter Personal computer Windo
Using the Battery Grip If you plan to use the camera with Battery Grip BG-E2, originally dedicated to the EOS 20D and EOS 30D, read the following. For instructions other than “Detaching the Battery Compartment Cover” and “Battery Life” explained below, refer to the Battery Grip BG-E2 Instruction Manual. If you have Battery Grip BG-E2N, read the BG-E2N’s Instruction Manual. Detaching the Battery Compartment Cover Put the camera on a flat surface and hold it firmly so it does not fall.
Specifications • Type Type: Recording media: Image sensor size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera with built-in flash Type I or II CF card * Compatible with Microdrive and 2GB and larger CF cards * Recording to USB external media enabled with Wireless File Transmitter WFT-E3/E3A attached 22.2 x 14.8mm Canon EF lenses (including EF-S lenses) (35mm-equivalent focal length is approx.1.
Specifications Recording functions: Backup recording: With the WFT-E3/E3A attached, image recording to the CF card and to USB external media connected to the WFT-E3/E3A will be possible as follows: (1) Standard (2) Automatic switching of recording media (3) Separate recordings according to image-recording quality (4) Recording images having the same size Enabled with WFT-E3/E3A attached • White Balance Type: Auto white balance: Color temperature compensation: Auto, daylight, shade, cloudy, tungsten lig
Specifications AF point selection: Automatic selection, manual selection Selected AF point display: Superimposed in viewfinder and indicated on LCD panel AF-assist beam: Small series of flashes fired by built-in flash Effective range: Approx. 4.0 m/13.1 ft. at center, approx. 3.5 m/11.5 ft. at periphery • Exposure Control Metering modes: Metering range: Exposure control: 35-zone TTL full-aperture metering • Evaluative metering (linkable to any AF point) • Partial metering (approx.
Specifications Flash coverage: 17mm lens angle of view Flash exposure compensation: ±2 stops in 1/3- or 1/2-stop increments FE lock: Provided • External Speedlite Compatible flash: EX-series Speedlites Flash metering: E-TTL II autoflash Flash exposure compensation: ±2 stops in 1/3- or 1/2-stop increments FE lock: Provided External flash settings: Flash function settings, Flash C.
Specifications • LCD Monitor Type: Monitor size: Pixels: Coverage: Brightness adjustment: Interface languages: TFT color liquid-crystal monitor 3.0 in. Approx. 230,000 Approx. 100% 7 levels provided 18 • Image Playback Display format: Highlight alert: Single image, Single image + Image-recording quality, shooting information, histogram, 4- or 9-image index, magnified view (approx. 1.
Specifications • Power Source Battery: Battery life: Single Battery Pack BP-511A, BP-514, BP-511, or BP-512 * AC power can be supplied via AC Adapter Kit ACK-E2 * With Battery Grip BG-E2N or BG-E2 attached, size-AA batteries can be used [Number of shots • approx.
Specifications Working humidity: 85% or less Dimensions (W x H x D): 91 x 67 x 31 mm / 3.6 x 2.6 x 1.2 in. Weight: Approx. 115 g / 4.1 oz. • Battery Charger CB-5L Compatible battery: Power cord length: Recharging time: Battery Pack BP-511A, BP-514, BP-511, or BP-512 Approx. 1.8 m / 5.9 ft. BP-511A, BP-514: Approx. 100 min. BP-511, BP-512: Approx. 90 min. Rated input: 100 - 240 V AC Rated output: 8.
Specifications Max. diameter x length: Weight: Hood: Case: 78.5 x 92 mm / 3.1 x 3.6 in. Approx. 475 g / 16.8 oz. EW-73B LP1116 All specifications above are based on Canon’s testing standards. The camera’s specifications and exterior are subject to change without notice. If a problem occurs with a non-Canon lens attached to the camera, consult the respective lens maker. Trademarks Adobe is a trademark of Adobe Systems Incorporated. CompactFlash is a trademark of SanDisk Corporation.
Digital Camera Model DS126171 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS — This manual contains important safety and operating instructions for Battery Charger CG-580 & CB-5L. 2. Before using the charger, read all instructions and cautionary remarks on (1) the charger, (2) the battery pack, and (3) the product using the battery pack. 3. CAUTION — To reduce risk of injury, charge only the Battery Pack BP-511A, BP-514, BP-511, or BP-512. Other types of batteries may burst, causing personal injury and other damage. 4.
MEMO 191
Index Index A AC Adapter Kit ..............................170 Access lamp ...................................29 A-DEP (Automatic depth-of-field AE)..........91 Adobe RGB.....................................74 AE lock............................................95 AEB (Auto Exposure Bracketing)....94 AF J Focusing AF start button........32, 160 AF stop button ..............................158 AI Focus AF ....................................77 Aperture-priority AE ........................
Index External Speedlite .........................105 Eyepiece cover .........................23, 97 F Faithful ............................................62 FE lock ..........................................102 File number .....................................72 Continuous / Auto reset / Manual reset File size...........................57, 117, 181 Filter effect (Monochrome)..............64 Yellow / Orange / Red / Green Flash 2nd-curtain sync .......................103 Custom Functions..................
Index ISO speed...............................59, 169 Automatic setting........................60 ISO expansion..........................154 J Jump display.................................119 L Landscape ................................50, 61 Language selection.........................41 LCD monitor....................................13 Brightness adjustment..............125 Image playback ........................115 Menus.........................................36 Shooting functions....................
Index Switch .........................................32 Printing..........................................133 Layout.......................................137 Paper settings...........................136 PictBridge .................................133 Print Order (DPOF)...................143 Printing effects ..........................138 Tilt correction ............................141 Trimming...................................141 button ..................139, 149 Program AE ..........................
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.
