Océ PRISMAsync Flowing productivity. Impressive colour.
Copyright © 2011 Océ All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from Océ. Océ makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
Contents Contents Chapter 1 Instructions for safe use.....................................................................................5 Instructions for safe use............................................................................6 Chapter 2 Regulation notices............................................................................................11 Regulation notices....................................................................................12 Chapter 3 General information...........
Contents 4
Chapter 1 Instructions for safe use
Instructions for safe use Instructions for safe use Introduction All products have been tested in accordance with the strictest international safety standards. Please read the following sections before you connect the machine to the power supply. These sections contain important information with regard to the user safety and the prevention of equipment problems. Make sure that you observe the safety rules hereinafter. This helps to assure safe operation of the product.
Instructions for safe use Disassemble and modification Warning ■ Do not remove covers and panels which are fixed to the machine. Some machines have a high-voltage component or a laser beam source inside that could cause electrical shock or blindness ■ Do not modify this machine, because this could cause a fire, electrical shock or breakdown. If the machine contains a laser, the laser beam source could cause blindness. Caution ■ Do not place any liquids on the machine.
Instructions for safe use Grounding Warning ■ Connect the power cord to an electrical outlet (wall socket) that is equipped with a grounding terminal. ■ This equipment was not designed for connection to an IT power system. An IT power system is a voltage network in which the neutral wire is not grounded. Installation Warning ■ Make sure that the machine is placed on a level, horizontal surface of sufficient strength. ■ Do not place this machine on an unstable or tilted bench.
Instructions for safe use ■ LCD display. Do not rub, press or touch the display surface with hard material, because the polarizer at the surface can be easily scratched. The LCD module consists of glass. Therefore, the LCD module can damage when you drop, pinch strongly or punch the module. If glass breaks, be careful that you do not get injured by the glass fragments. Contact your authorized service representative.
Instructions for safe use 10 Chapter 1 - Instructions for safe use
Chapter 2 Regulation notices
Regulation notices Regulation notices Introduction This section describes the regulation notices. Radio Interference suppression (all countries except USA) Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC approval (USA-only) This system has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC Rules.
Regulation notices with the CDRH regulations and must be attached to laser products marketed in the United States. Caution Use of controls, adjustments, or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This is a semiconductor laser. The maximum power of the laser diode is 21 mW and the wavelength is 658 nm.
Regulation notices End of Life; WEEE (EU-only) The symbol "the crossed-out wheeled bin" indicates that at end-of-life of the equipment separate collection is required in the EU Member States. The black bar specifies that the appliance is put on the market after August 13, 2005. Reference: Directive 2002/96/EC. Contact your local organization for further information.
Regulation notices Automatic duplex Using both sides of paper reduces paper costs, national energy consumption and the amount of paper in the waste disposal process. Therefore, thePRISMAsync is default set for automatic duplex copying and printing.
Regulation notices 16 Chapter 2 - Regulation notices
Chapter 3 General information
Caution labels and notations Caution labels and notations Introduction You can find the power-marking label at the bottom side of the controller. If connection to a different mains voltage is required, contact your authorized service representative. Do not remove caution labels or caution notations. If a label or notation is soiled, please clean the label or notation. If you cannot make label or notation legible, or if the label or notation is damaged, please contact your service representative.
+1
- Beyond the Ordinary o Printing for Professionals CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROPA N.V. Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands (See http://www.canon-europe.com/ for details on your regional dealer) Creating global leadership in printing CANON LATIN AMERICA, INC.
