User Manual Dishwasher
Thank you for purchasing a Candy product Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance. Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
Safety and warnings Your dishwasher has been carefully designed to operate safely during normal dishwashing procedures. Please keep the following instructions in mind when you are using your dishwasher. WARNING Electrical shock hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current.
safety and warnings ● Use only detergents or rinse aid recommended for use in a domestic dishwasher and keep them out of reach of children. ● Check that the detergent dispenser is empty after the completion of each wash program. ● When loading items to be washed, locate sharp items so that they are not likely to damage the dishwasher and load sharp knives with the handle up to reduce the risk of cut-type injuries.
safety and warnings ● Keep the area around/underneath your appliance free from the accumulation of combustible materials, such as lint, paper, rags and chemicals. Operational safety instructions ● Open the door very carefully if the dishwasher is in operation. There is a risk of being sprayed with hot water. Do not open the door fully until the spray arms have stopped rotating. ● The door should not be left in the open position as this could present a tripping hazard.
Installation instructions Parts supplied Drain hose support (1) Inlet hose (1) Salt funnel(1) Installation and User Instructions Prior to installation Unpacking and handling ● Check packaging and dishwasher for signs of transport damage. If the dishwasher is in any way damaged, do not install it. Contact the dealer the dishwasher was purchased from. ● Disposal of packaging: some of the packaging is recyclable. Check the symbols and labels and recycle if possible.
Installation instructions 1 Product dimensions C A B C E F G D 5
Installation instructions PRODUCT DIMENSIONS MM A Overall height of product with top panel in place with top panel removed* B Overall width of product C Overall depth of product D Depth of open door (measured from front of kickstrip) CABINETRY DIMENSIONS E Inside height of cavity with top panel in place with top panel removed* 846 - 866** 816 - 836** 448 605 1185 MM 850 - 870** 825 - 845** F Minimum inside width of cavity 450 G Minimum inside depth of cavity 605 * The top panel may be
Installation instructions 2 Cavity preparation Preparing the product and cabinetry The top panel may be removed to suit underbench cavity height. See the illustrations below.
Installation instructions IMPORTANT! To prevent possible steam damage to the cabinetry, ensure that any bare wood surrounding the dishwasher is sealed with an oil-based paint or moisture-proof polyurethane. IMPORTANT! The power outlet must be located in a cabinet adjacent to the dishwasher cavity. 6 Dia. 50mm 4 8 Services can be located either side of the dishwasher. Ensure that any services hole has a minimum diameter of 50mm.
Installation instructions 3 Plumbing and drainage options. Determine which is more suitable 1 38mm step 4 min. 750 mm 2 min. 120mm If space is limited for fixing, push hose through drain hose support to required height 750-882.5 mm Dishwasher and Ø 38 mm Standpipe min.
Installation instructions Dishwasher using drain hose joiner onto sink trap/waste tee Installer to provide drain hose joiner to suit min. 15mm waste tee 750-882.5 mm If space is limited for fixing, push hose through drain hose support to required height 2 3 min. radius 200 mm IMPORTANT! Ensure drain hose is routed straight to joiner. Remove excess drain hose material if necessary. Do not shorten the inlet hose. 10 min. 500 mm step 4 750 - 882.
Installation instructions 4 Connect inlet hose to cold water min. 10mm 3/4” BSP connector Ensure the supplied rubber washer is fitted inside the coupling. 180 o 1 2 No leaks! Tighten coupling with spanner. Plumbing -- Water inlet connection IMPORTANT! The appliance should be connected to the water main using the new water inlet hose supplied.Old hoses should not be used. ● Do not shorten the inlet hose. ● 1.Take note of water connection requirements.
Installation instructions 5 Plug product in Electrical connection The dishwasher must not be connected to the electrical supply while installation is being carried out. Ensure all domestic wiring is properly earthed. ● Check the rating label (located on the left-hand side of the dishwasher’s stainless steel inner door) and ensure that the voltage and frequency values for the current in the house correspond to those on the rating label.
Installation instructions Final checklist To be completed by the installer Check all parts are installed. Ensure that all panels and parts thereof are secure and final electrical tests have been conducted in accordance with local electrical regulations. ● Check that the dishwasher is level. If necessary, adjust the levelling feet slightly. To ensure optimum performance, the dishwasher should not be inclined more than 1o. Check with a spirit level.
Product Description 2 4 14 5 1 6 3 7 8 9 10 1. Upper basket 6. Rating label 2. Upper spray arm 7. Detergent dispenser 3. Lower spray arm 8. Rinse aid dispenser 4. Cutlery basket 9. Salt container 5. Lower basket 10.
Overview of programmes On some models without Digital 7 1 8 2 9 3 4 12 10 11 5 6 1. ON / OFF button 2. PROGRAMME SELECT button 3. Lack Salt and Rinse Aid reset button 4. Additional function button * 7. Rinse Aid indicator 8. PROGRAMME indicator 9. Additional function indicator 10 START DELAY/Status Indicators 5. START DELAY button 11. Salt Aid indicator 12. Child Lock * 6.
Overview of programmes On some models with Digital 7 1 2 3 1. ON / OFF button 2. PROGRAMME SELECT button 3. START DELAY button 4. Additional function button * 5. Lack Salt and Rinse Aid reset button 8 9 10 4 11 5 6 7. Time & Info Display 8. Speed Up function Indicator 9. Multi-tab function Indicator 10. Add dish Indicator/1/2 function Indicator 11. Child Lock * 6.
Overview of programmes Programmes Programmes P1 Type of food residue ECO 50°C 298min P2 Universal P3 Intensive P4 P5 Type of load 60°C 115min 70°C 130min Prewash 45°C 20min 1) Zoom 45°C 32min Models with Digit also have the following programs: P6 P7 P8 Special 45°C 72min Glass 45°C 98min AUTO WASH 2) 45-70°C 148min 1) Use this programme to quickly rinse the dishes. T his prevents the remaining food to bond on the dishes and bad odours to come out from the appliance.
Water softening system To ensure good washing results,the dishwasher requires soft water.Hard water can be detrimental to the performance of your dishwasher. Over time,glassware washed in hard water will become opaque and dishes will become spotted or covered in a white film. Using very hard water can cause dishwasher parts to fail over time.Salt can improve the situation.
Water softening system Using special salt As soon as the low salt indicator is lit on the control panel ,salt should be topped up.Always refill with special salt immediately before switching on the appliance.This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. Top up the salt as follows: CAUTION Only use dishwasher salt. Other products can cause damage to the appliance! Any spilled salt causes corrosion.Run a programme after each refill. 1.
Using rinse aid We highly recommend using liquid rinse aid regularly to get the best drying results.Rinse aid gives a streak-free, sparkling clean look to glass and chinaware. In addition, it prevents metal from tarnishing. When to refill the rinse aid dispenser When rinse aid level becomes low,the digtial will scrolling display ADD RINSE AID to remind you to refill the dispenser.
Utensils IMPORTANT! Never put highly absorbent materials, such as sponges and towels in your dishwasher.Do not put dishes or cutlery that have been soiled by tobacco ash, wax, lubricating grease or paint in your dishwasher. Cutlery and silverware All cutlery and silverware should be rinsed immediately after use to prevent tarnishing caused by some foods. Silver items should not come into contact with stainless steel, e.g. other cutlery. Mixing these items can cause staining.
Loading utensils If the tableware or cookware rack is burnt, scorched,sticky, and other food which is very difficult to removed, it is advisable to soak it for a period of time before washing it or pre-dispose it with a dish cloth or else it will be hard to clean.Remove any large food particles before placing dishes in the dishwasher. It is not necessary to prerinse utensils under running water. Upper rack ● The upper rack is designed to hold items like glasses, cups, saucers, plates and shallow pans.
Loading utensils To adjust the upper rack: IMPORTANT! Before you adjust its height,make sure the basket is empty. Remove: Replace: End Cap Rollers Rail Rail Rollers End Cap 1.Fully extend the upper rack and rotate open the two plastic end caps on the front of the rails. 2.Remove the upper rack. 3.Select the set of rollers on the side of the rack that provides the desired height, and reinstall the upper rack by guiding the rack rails between the appropriate set of rollers. 4.
Loading utensils Cutlery basket ► ► ► ► Mix spoons with other cutlery to prevent them to bond together. Use the grid element in order to separate the cutlery. Place Cutlery with the handles down for better washing results. If long items may block the spray arms find a horizontal positioning in the upper basket. CAUTION Put sharp and pointed items with the blade pointing downward to keep them out of harms way.
Adding detergent IMPORTANT! Only use detergents recommended for automatic dishwashers. Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with the skin and eyes and keep children and infirm persons away from the dishwasher when it is open. Check that the detergent dispenser is empty after completion of each wash programme. Never sprinkle or pour detergent directly onto any item in the dishwasher.
Before first Use How to Adjust User Preference Settings for LED Models During the selection of programmes, press and hold for about 5 seconds to enter the user preference settings. User preference settings include Water Softener setting,Buzzer setting,Rinse Aid setting and Memo Mode setting. 1.The appliance is switched on. 2. Press and hold the for 5S to enter the user setting mode, and all LEDs will flash for 1s and then turn off.
Before first Use How to Adjust User Preference Settings for DIGIT Models During the selection of programmes, press and hold the program selection key for 5S to enter the user setting mode.User setting mode includes Language setting, Water Softener setting, Buzzer setting,Rinse Aid setting and Memo Mode setting. 1.The appliance is switched on. 2. Press the program selection key to enter the Language setting menu, and the display will show the current language.
Daily Use Start a Programme 1. Open the door and Press the ON/OFF button *The display will show the wash programme time 2.Press 3. Press to turn the dishwasher on. to select the program you want on the dishwasher control panel. to start the programme and close the door. NOTICE If the MEMO MODE YES The appliance remembers the last programme you used. The next time the appliance will switch on, the appliance pre-selects the programme last used. Pause and restart a wash programme 1.
Daily Use Cancel a Delayed Start When the current reservation time is displayed for 24h,or other time. Press the reservation button again to cancel the reservation. Cancel Start Delay / Programme 1. Press the or for about 3 second. The start delay is cancelled. The programme is aborted. The appliance is switched off. 2. Start a new programme and a delayed start if desired. CAUTION If a programme will be aborted in the process of washing dishes, the residue of detergent remains on the dishes.
Care and cleaning Over time, food residue or limescale deposits may accumulate inside your dishwasher.These may reduce efficiency, and food residue may produce a bad odour. Inspect and clean your dishwasher regularly. IMPORTANT ! ● Before any cleaning or maintenance, always disconnect the dishwasher from the power supply, turn off the water supply, and wait until all parts of the dishwasher have cooled.
Care and cleaning To remove the drain filter, turn the filter anti-clockwise to release, then lift out. Once the drain filter has been removed you can lift the filter plate out. ● Rinse them thoroughly under running water and then replace. Replace the filters correctly after cleaning, making sure the filter plate is flush with the dishwasher base. ● ● IMPORTANT ! When cleaning the underside of the filter plate, take care handling its sharp outer edge.
Care and cleaning Cleaning the centre spray arm ● ● To remove the centre spray arm, carefully unscrew its locking nut. Rinse the spray arm thoroughly under running water, then refit. IMPORTANT ! Make sure you twist the locking nut on the centre spray arm firmly back on the water supply tube.Check that the centre spray arm is firmly locked in place and rotates freely.
Troubleshooting Many occuring problems could be solved by yourself without specific expertise. In case of a problem please check all shown possibilities and follow below instructions before you contact an after sales service. CAUTION Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. ● Electrical equipment should be serviced only by qualified electrical experts, because improper repairs can cause considerable consequential damages.
Troubleshooting Error codes on the display Problem Acoustic alarm, display shows ALARMCODE A10 The appliance does not fill with water. Acoustic alarm, display shows ALARMCODE A20 The appliance does Acoustic alarm, display shows ALARMCODE F30 Leak: The drain pump runs permanently! Possible cause Possible solution Water tap is closed. Open the water tap. Note: Whenever Error is solved switch off the appliance and restart the programm.
Troubleshooting Washing Results are not satisfactory Problem Possible cause Possible solution Filters are clogged. Clean the filters. Make sure that the filters Filters are not correctly are correctly assembled and assembled and installed. installed. Spray arms are clogged. Remove remaining food remnants with a thin pointed object. Make sure that the Programme was not programme is applicable for applicable for the type of load the type of load and food and food remnants. remnants.
Troubleshooting Problem Possible cause Possible solution Dry water drop stains on glasses and dishes. Rinse aid dosage is too low. Increase the released quantity of rinse aid. Q u a l i t y o f r i n s e a i d o r Cleaning product too old; Multitab.stains on glasses change the product. • Programme had no drying phase. The dishes are wet. • Programme had a low temperature drying phase. The dishes are wet and matte.
Technical Data Candy Suppliers name or trade mark Supplier´s model identifier CDPH 1L952W CDPH 1L952X CDPH 1L949W CDPH 1L949X Rated capacity in standard 9 9 9 9 Energy efficiency class 1) A+ A+ A+ A+ 222 222 222 222 0.74 0.74 0.74 0.74 0.3 0.3 0.3 0.
Technical Data Candy Suppliers name or trade mark Supplier´s model identifier CDPH 2L949W CDPH 2L949X CDPH 2L1049W CDPH 2L1047X Rated capacity in standard 9 9 10 10 Energy efficiency class 1) A++ A++ A++ A++ 197 197 211 211 0.69 0.69 0.74 0.74 0.3 0.3 0.3 0.
Technical Data Candy Suppliers name or trade mark Supplier´s model identifier CDPH 2D947W CDPH 2D947X Rated capacity in standard 9 9 Energy efficiency class 1) A++ A++ 197 197 0.69 0.69 0.3 0.
