Installation Guide

iv. Once connections of wires are
completed, carefully tuck wires and
wire nuts into the outlet box making
sure no bare wire (on the black and
white) is visible at the wire nuts. Slide
canopy into position and tighten in
place by nut into position.
Note: If required, hook the support
arms onto fixture and then into the
glass (or hoop).
Note: If required assemble centre body
of fixture.
B. For Semi Flush Mount
installation:
i. Mount the mounting bracket to
outlet box using outlet box screws (not
included). Make sure the studs or
nipple on the mounting bracket are
facing out from the outlet box.
ii. Remove the loop and cap by
unscrew the 2 cap nuts and starwasher.
iii. Connect the ground wires
(bare copper or green) from your
fixture to the ground wire (bare
copper or green) or ground screw
in the electrical outlet box.
Connect the black wire (or wire
marked “SPT-1”) from the fixture to
the black wire in the electrical box
and connect the white wire from
the fixture to the white wire in the
electrical box.
iv. Once connections of wires are
completed, carefully tuck wires and
wire nuts into the outlet box making
sure no bare wire (on the black and
white) is visible at the wire nuts.
Position fixture over studs on
mounting bracket assembly. Secure
fixture in place with star washers and
cap nuts.
4. Install proper bulb type and
wattage (not included).
1. Spread the arms evenly (optional).
2. Attach the mounting bracket to the
outlet box using electrical box screws (not
included) . Attach the nipple to the
mounting bracket and adjust until it will
clear the canopy when assembled (Place
the canopy over the nipple and tighten
the upper connector onto the nipple until
snug. The upper connector should hold
the canopy snug to the ceiling). Lock the
nipple in the correct position using the
hex nut.
A. For Chandelier Mount
installation:
i.
To attach chain loop to light fixture, use
a screwdriver and wrench to open and
close chain loop. Ensure the opening is
closed. Weave the power cord and
ground wire through the links in the
chain.
ii. Loosen the nut on the upper
connector and slide it down the chain
towards the lower connector. Slide the
canopy down the chain towards the lower
connector. Feed the wire through nut,
canopy, the upper connector and onto
the nipple. Tighten the upper connector
onto the nipple. Spread the other end of
the chain open and fasten to the upper
connector. Ensure the opening is closed.
iii . Connect the ground wires (bare
copper or green) from your fixture to the
ground wire (bare copper or green) or
ground screw in the electrical outlet box.
Connect the black wire (or wire marked
“SPT-1”) from the fixture to the black wire
in the electrical box and connect the
white wire from the fixture to the white
wire in the electrical box.
INSTALLATION:
Star
Washer
Cap
Nut
Stud
C-25b
06/12
Bulb
Finial
Cap
Decorative
Glass
Hex Nut
Fibre
Washer
(not included)
Outlet
Box
Mounting
Bracket
Power
Cord
Chain
Connector
Lower
White
Black
House supply
Ground wire
Fixture
Ground wire
Canopy
Nipple
Upper
Connector
Nut
White
Black
House supply
Ground wire
Fixture
Ground
wire
Canopy
Nut
Nipple
Hex Nut
Outlet Box
Outlet Box Screws
(not included)
Mounting
Bracket
Ground
Wire
Ground
Wire
Outlet
Box
Screws
Loop
Cap Nut
Cap
Stem
Rod
Small Metal
Cover
Big Mrtal
Cover
3. Attach the stem to the fixture.
Secure the glass in place using
the decorative cap, hex nut,
fibre washer and finial.
TOOLS AND MATERIALS REQUIRED:
SAFETY PRECAUTIONS:
Star-headed
Screwdriver
Wire Cutters
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
NOTE: Product May Not Look Exactly As Shown In Figures.
Pliers Wrench
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
CHANDELIER
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]