User guide

ManualsBrandsC2G ManualsTools13138 TC-NT1 Network Cable Tester

CONTENTS

TC-NT1 Network Cable Tester

(Includes master box and remote unit)

INTRODUCTION & FEATURES ........... 1

PRODUCT PROFILE .......................... 2

OPERATION

I. Loopback Test ......................... 3,4

II. Remote Test ........................... 5,6

Summary of content (7 pages)

PAGE 1
CONTENTS TC-NT1 Network Cable Tester (Includes master box and remote unit) INTRODUCTION & FEATURES ........... 1 PRODUCT PROFILE .......................... 2 OPERATION I. Loopback Test ......................... 3,4 II. Remote Test ...........................
PAGE 2
INTRODUCTION The TC-NT1 Network Cable Tester is an innovative, practical tester that can easily read the correct pin configuration of 10BASE-T, 10BASE-2, RJ45/RJ11 modular, 258A, TIA-568A/568B and Token Ring cables by comparing one transmitting end to the corresponding receiving end. The included remote terminator allows the user to test installed cable either at a wall jack or a patch panel.
PAGE 3
PRODUCT PROFILE 1 2 8 LANtest 7 TRENDnet Network Cable Tester TEST 9 3 4 1 2 3 4 5 6 7 8 12345678G 6 5 AUTO MANUAL Remote Terminator PIN-OUT INDICATOR OFF ON 10 GND NOT FOR LIVE CIRCUITS Remote Unit Main Unit 11 (Diagram 2) 1. RJ45 JACK 2. RJ45 JACK 3. LED DISPLAY FOR SOURCING END (JACK 1) 4. LED DISPLAY FOR RECEIVING END (JACK 2) 5. POWER SWITCH 6. LED SCANNING MODE SWITCH 7. TEST SWITCH FOR MANUAL SCAN 8. RJ45 JACK 9. LED DISPLAY FOR RECEIVING END (SAME AS JACK 2) 10.
PAGE 4
OPERATION I. Loopback Test 1. 10Base-T Test 1.1 Plug one end of the tested cable into the transmitting RJ45 jack on the master unit marked with a ' ' and the other end of the cable into the remaining receiving RJ45 jack. 1.2 Slide power switch on. The upper row of LEDs will start to scan in sequence if the Auto/Manual button is set on "Auto" mode. The LED for pin 1 will light up if the button is in "Manual" mode. 1.
PAGE 5
2. RJ11 Modular Cable Test 2.1 Please follow directions for the UTP/STP Cable Test and refer to Diagram 4 for the correct LED pin out display RJ11 1 2 3 4 5 6 (Diagram 4) 1 2 3 4 5 6 7 8 G RJ45 3. Coaxial Cable Test 3.1 Plug the two attached BNC adapter cables on both RJ45 jacks. Then connect the tested cable to each end of the BNC adapter cables 3.2 For the remaining testing procedures, please refer to steps 1.2 to 1.5 Note: 1. The center pin of BNC should be read on LED 2. Please refer to diagram 5.
PAGE 6
II. Remote Test 1. Plug one end of the tested cable to the transmitting RJ45 jack on the master unit marked with a ' ' and plug the other end into the remote terminator. If the tested cable is installed in a patch panel or wall plate, you may use the included patch cable to solve the connector gender problem. Please refer to Diagram7 & 8. 2. Now, set the Auto/Manual switch to Auto mode for one-person testing. 3. Read the test results from the LED display on remote terminator.
PAGE 7
Test Results 1.Continuity: Pin 2 has continuity 1 2 3 4 5 6 7 8 G Pin 2 is opened 2.Open: 1 2 3 4 5 6 7 8 G Pin 2 and Pin 3 are shorted 3.Short: 1 2 3 4 5 6 7 8 G Pin 3 and Pin 6 are miswired 4.Miswire: 1 2 3 4 5 6 7 8 G Caution: 1. Operating the tester in live circuits may damage the tester 2.