bathroom VENTILAtion fan MODEL: BV-BF-02-PLUS INSTALLatiON MANUAL and USER GUIDE
Table of Contents Hardware Included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Installation - New Construction. . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation - Existing Construction. . . . . . . . . . . . . . . . . . . . . 10 Care and Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty LIMITED LIFETIME WARRANTY WHAT IS COVERED If this product fails due to a defect in materials or workmanship at any time during the first THREE years of ownership, the manufacturer will replace it free of charge, postage-paid at their option. This warranty does not cover products that have been abused, altered, damaged, misused, cut or worn. This warranty does not cover use in commercial applications. Use only manufacturer-supplied genuine warranty repair replacement parts to repair this fan.
Pre-Installation TYPICAL INSTALLATION The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated air flow.
Pre-Installation (Continued) WIRING DIAGRAMS WIRING INSTRUCTIONS To be sold only with installation instructions. WARNING: Wiring must comply with all applicable electrical codes. Turn OFF power before removing or installing connectors. WARNING: USE COPPER TO COPPER ONLY. Do not use aluminum wire. CAUTION: The accessory part (wire nut) should meet the installation instructions below. NOTICE: Important wire information. Maximum temperature rating 105˚ C (221˚ F).
Pre-Installation (continued) PLANNING INSTALLATION Before beginning the product installation, make sure all parts are present. Compare parts with the package contents list and hardware contents. If any part is missing or damaged, do not attempt to install the product. 1. Carefully remove the unit from the carton. WARNING: Turn off the electricity at breaker box before beginning installation. 2.
Pre-Installation (continued) PACKAGE CONTENTS C D A E B Part Description Quantity A Fan housing 1 B Grille 1 C Suspension bracket 1 1 D Suspension bracket 2 1 E Suspension bracket 3 1 7
Installation - New Construction CAUTION: Make sure the power is switched off at the service panel before starting installation. NOTE: Ceiling mount only. 1 2 Attaching the fan housing to the ceiling joist CAUTION: Allow for the thickness of ceiling board used in your application. Do not flush mount to the joist. The flange should be flush with the bottom of the ceiling board. Attaching the fan housing to the ceiling joist using suspension brackets □□ If spacing between joists is 16 in. - 24 in.
Installation - New Construction (continued) 5 6 Removing the wiring cover on the fan housing Connecting the duct □□ Connect a 4 in. circular duct (not supplied) and vent to the outside. Secure it with duct tape (not supplied) or a clamp (not supplied) to make the connection secure and airtight. □□ Remove the wiring box cover (1). Pull the house wires through the wire box cover hole.
Installation - Existing Construction CAUTION: Make sure the power is switched off at the service panel before starting installation. 1 Removing the existing fan 3 Enlarging the opening (optional) □□ Remove the old fan from the ceiling. □□ If this fan is not replacing an old fan, cut a 9.25 in. x 8.9 in. opening for the fan body (A). 2 Measuring the ceiling opening 4 Removing the motor and power line □□ Measure the opening to ensure it is large enough to accommodate the new fan body (A) (9.25 in.
Installation - Existing Construction (Continued) 5 Removing the duct □□ Loosen the one machine screw (BB) from the housing (A) and remove the duct connector (1). 6 Removing the junction box □□ Remove the junction box (1) from the housing (A) by loosening and removing the machine screw (BB). BB A 1 1 A BB 7 8 Installing the housing □□ Pull the house wires through the wire cover hole (1). □□ Pull the 4 in. circular duct (not provided) through the housing.
Installation - Existing Construction (Continued) 9 10 Connecting the duct Reinstalling the junction box □□ Reinstall the junction box (1) into the housing using the previously removed screw (BB). □□ Using duct tape or a hose clamp (not included), attach the 4 in. circular duct (not included) to the duct connector (1). BB □□ Reconnect the duct connector using the previously removed screws (BB).
Care and Maintenance WARNING: Disconnect the power supply before servicing. □□ See SAFETY INFORMATION before proceeding. Routine maintenance should be done at least once a year. □□ Never use solvents, thinner or harsh chemicals for cleaning the fan. □□ Do not allow water to enter the motor. □□ Do not immerse metal parts in water. Troubleshooting Problem The fan seems louder than it should. Possible Cause Solution The CFM is too great.