Use and Care Manual

ManualsBrandsBuyers Products Company ManualsOutdoor Power EquipmentExtender Bracket for Buyers Products TGS03 Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

TGS03 Salt Spreader

TGS03RED Salt Spreader

TGS03YEL Salt Spreader

US PATENT 8,888,025; 9,562,333

other PATENTS PENDING

—continued inside

WARNING

Observe the following Safety Precautions before,

during and after operating this spreader. By following these

precautions and common sense, possible injury

to persons and potential damage to this machine may be

avoided.

SPREADER WARRANTY

This warranty replaces all previous warranties and no

employee of this company is authorized to extend additional

warranties, or agreements, or implications not explicitly

covered herein.

Buyers Products Company warrants all parts of the product

to be free from defects in material and workmanship for a

period of one (1) year. Parts must be properly installed and

used under normal conditions. Normal wear is excluded.

Any part, which has been altered, including modifications,

misuse, accident, or lack of maintenance will not be

considered under this warranty.

The sole responsibility of Buyers Products Company under

this warranty is limited to repairing or replacing any part(s),

which are returned, prepaid, 30 days after such defect is

discovered, and returned part(s) are found to be defective by

Buyers Products Company.

Authorization from Buyers Products Company must be

obtained before returning any part. The following information

must accompany defective parts returned to Buyers

Products Company: RMA #, spreader model, serial number,

date installed, and distributor from whom purchased.

Buyers Products Company shall not be liable for damage

arising out of failure of any unit to operate properly, or failure,

or delay in work, or for any consequential damages. No

charges for transportation or labor performed on any part will

be allowed under this warranty.

Safety Precautions

1. Read this entire Installation Instruction before oper-

ating this spreader.

2. Read all safety decals on the spreader before

operating.

3. Verify that all personnel are clear of the

spreader spray area before starting or operating this

spreader.

4. Do not adjust, clean, lubricate or unclog material

jams without first turning off the spreader.

5. Make sure the spreader is securely fastened to the

vehicle in accordance with this manual.

6. Do not operate a spreader that is in need of mainte-

nance or repairs.

7. Always disconnect the battery before removing or

replacing electrical components.

Spreader Assembly

Check contents of box against parts list to make sure

all components are included. When ordering replace

ment or spare parts refer to parts list for part numbers.

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Installation Instructions TGS03 Salt Spreader TGS03RED Salt Spreader TGS03YEL Salt Spreader US PATENT 8,888,025; 9,562,333 other PATENTS PENDING Safety Precautions WARNING Observe the following Safety Precautions before, during and after operating this spreader.
PAGE 2
1. Slide frame #3019400 into hitch receiver. Fig. 1. Fig. 1 2. Slide hopper assembly #3019372 between frame uprights with front portion rested on the truck’s bumper. Fig. 2. Fig.
PAGE 3
5. Assembly ½-13 x 6.0 screws as shown in Fig.5. Make sure that nuts located between hopper flange and frame positioned exactly as shown. These nuts must not be in contact with hopper and frame at this time. 3. Align holes in rear portion of the hopper with slots in frame uprights. Use slots which will position spreader with a slight upward tilt. Secure hopper assembly to frame using ½-13 x 3.0 screws, flat washers and nuts. Fig.3. Do not tighten fasteners at this time. Apply Antiseize on Fig.
PAGE 4
7. Attach shield #3015707 to trough bracket as shown in Fig.7 9. Attach spinner disk to gear motor shaft as shown in Fig.9. Secure disk on shaft using clevis pin and cotter pin. Fig. 7 Fig. 9 SCREW 3/8-16 X 1.0 WASHER FLAT 3/8 SPINNER DISK 3019561 NUT NYLOCK 3/8-16 SHIELD 3015707 CLEVIS PIN1420014 COTTER PIN FPC007800075 10. Attach bracket and handle of draw latch to lid #3019410 using 2 10-24 screws as shown in Fig.10. Attach draw latch catcher to the hopper as shown in Fig.11. 8.
PAGE 5
THIS IS WIRE GROUND ELECTRICAL SYSTEM! NO CONNECTIONS TO TRUCK’S FRAME OR BODY ALLOWED! CAUTION DO NOT MOUNT CONTROLLER IN THE WAY OF AIR BAG DEPLOYMENT! NOTE: Always disconnect battery before attempting to install electrical components on your vehicle. Mount the controller in a convenient location in the truck cab. It is recommended not to mount the controller directly in front of heat vents. Allow ample air space around controller.
PAGE 6
Spreader Operation. Controller Warnings. 1. Due to the rate at which materials absorb moisture differently, some materials may not perform as desired. Therefore, the substitution of an alternative material may be necessary for optimum performance. 2. When filling hopper use only screened material. Prevent large chunks of material and debris from getting into hopper and cause operational problem or damage. 3. Material must never be left in the hopper for extended period of time.
PAGE 7
3 7 TGS03 Tailgate Auger Bill of Materials ITEM PART NO. 1 2 1 3 4 5 6 7 2 4 5 6 QTY. DESCRIPTION 3019372 3026555 3026557 3019400 3019410 3026564 3026565 3019561 3015707 3018923 3019408 1 1 1 1 1 1 1 1 1 1 1 HOPPER ASSEMBLY HOPPER ASSEMBLY, RED HOPPER ASSEMBLY, YELLOW FRAME TGS03 LID TGS03 LID TGS03, RED LID TGS03, YELLOW SPINNER, 12 IN TGS SHIELD TGS07 DISC PROTECTOR HARDWARE BAG TGS03 TGS03 Hopper Assembly Bill of Materials PART NO.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TGS03 Trough Assembly 9 4 Bill of Materials 3 2 6 7 5 8 ITEM PART NO. QTY. DESCRIPTION 1 3015377 1 2 3 4 5 6 3015381 3015382 1411000 FWF031075006SS 3006721 1 1 1 4 4 7 FPY031000150 1 8 9 3014994 FNE038016044SS 1 4 10 11 12 13 14 15 3019374 3012144 FWF038100007SS FCS038016075SS FWF025063007SS 3016751 1 1 2 2 1 1 GEAR MOTOR DUAL SHAFT .