Installation Instructions

FILTRATION FAUCET INSTALLATION INSTRUCTIONS, page 4 of 4
Attach the braided black label
pressure tank hose to the blue
cold-water inlet on the dispenser.
Screw the tapered adapter onto the
red hot-water outlet. Use plumbers’
tape on the outside threads of the
outlet for a good seal.
Make sure that all lines are as straight
as possible and not kinked, as this
may adversely affect the performance
of the dispenser.
HOT ONLY and HOT/COLD FILTRATION FAUCET W/ BTI AQUA-SOLUTIONS DIGITAL INSTANT HOT WATER DISPENSER
ITEMS: H2100, H2200, H2400, HC2100, HC2200, HC2400, HT4105
8
Place the remaining metal pinch-
clamp on the open end of the clear
hose. Push the clear hose onto the
tapered adapter previously installed
on the red hot-water outlet. Secure
with pinch-clamp.
9 10
Turn on the water supply and check for
leak(s), ESPECIALLY at the water supply
and connection points. If leak(s) are
present, shut off the water supply, repair
the leak and re-test the system as
described.
Open the hot handle of the faucet and
turn on the water supply. Water will ow
from the faucet when the dispenser is
full.
ENJOY YOUR BTI FIL
TRATION
FAUCET AND DIGITAL INSTANT HOT WATER
DISPENSER!
www.btiaquasolutions.com • 7022 S. Revere Parkway Suite 240 • Centennial, CO 80112 • 720.322.0800 (o) 720.322.0801 (f)
FILTRATION FAUCET PRODUCT WARRANTY
BTI Aqua-Solutions provides warranties against functional and nish defects in material or workmanship for all Filtration Faucets, to the
original purchaser, in residential applications. Filtration Faucets are warrantied for FIVE YEARS for functional defects, for SEVEN YEARS for
Brushed Nickel and Polished Nickel nish defects, and LIFETIME for Chrome nish defects.
To le a warranty claim for a functional or nish defect, a dated receipt of purchase of the product from an Authorized BTI Dealer must accom-
pany the warranty request. To submit a warranty claim, contact: [e-mail]
Improper installation, the failure to perform proper maintenance, or uses for which the products were not designed are not warrantied. The
warranty will be void if the nish has been improperly cared for due to lack of cleaning or cleaning with improper cleaning materials which
result in damage. BTI Aqua-Solutions has no liability for indirect or consequential damages to its products. The nish warranty is for normal
wear and tear of the nished surface.
BTI Aqua-Solutions will repair or replace, at its option, any of the products listed above that BTI has determined to have a manufacturing de-
fect. BTI Aqua-Solutions is not responsible for any installation or labor charges and will not pay for any repair cost performed on its products
without prior written consent by a BTI Aqua-Solutions authorized representative.
CARE INSTRUCTIONS FOR CHROME, BRUSHED NICKEL AND POLISHED NICKEL FINISHES
IMPORTANT: It is the customer’s responsibility to check for any material nish defects BEFORE installation.
The best general maintenance is regular cleaning. Even though these nishes are considered durable, you CAN NEVER use any abrasive type
cleaners, sponges, cloths or pads to clean the xture. Always try to keep the nish clean and dry. Trapped moisture on the surface of the nish
can lead to staining. Astringent cleaners, chlorine, bleach, along with acidic based organic cleansers are potentially harmful to these nishes.
RECOMMENDED MAINTENANCE: Do not allow water spots to dry on the xture. Keep the surface dry and clean after use. All products should
be cleaned with a damp, clean, soft cloth and mild, nonabrasive soap to remove surface spots. Be gentle in your cleaning method. NEVER use
cleaners that contain bleach, abrasives or vinegar. NEVER use any type of abrasive sponge or pad.