User's Manual

ManualsBrandsBryant ManualsThermostatsBryant Thermostat 5200

MODEL

5200

OWNERS MANUAL

Premier Series

7-Day Programmable

2-Heat / 2-Cool & Heat Pump

Digital Thermostat

Compatible with low voltage multi-stage heat

pump systems with up to two stages of heating

and two stages of cooling. Not for use on

single-stage heating or cooling systems.

READ ALL INSTRUCTIONS BEFORE PROCEEDING

Store this

booklet for

future reference

Braeburn Systems LLC, as an Energy Star partner

has determined that this product meets the Energy

Star Guidelines developed by the U.S. Environmental

Protection Agency & the U.S. Department of Energy

for maximum energy efficiency.

WARRANTY

YEAR

LIMITED

CONTENTS

WARNING!

Quick Reference/Installation Guide

Important Safety Information

• Always turn off power to the air conditioning or heating system prior to installing,

removing, cleaning or servicing thermostat.

• Read this manual thoroughly prior to installing, programming or operating this

thermostat.

• This thermostat is designed for use with a 24 Volt AC low volta ge multi-stage heat

pump system.

• Do not use this thermostat on single stage systems or other systems with

voltages higher than 30 Volt AC.

• This thermostat requires 24 Volt AC power for normal operation and control of the

heating or cooling system.

• This thermostat also requires two (2) properly installed "AA" alkaline batteries to

retain user settings and programs in the event of loss of AC Power due to power

outage or rolling blackouts.

• Wiring must conform to all building codes and ordinances as required by local

and national code authorities having jurisdiction.

• Do not short (or jumper) across terminals on the gas valve or at the heating or

cooling system control board to test the thermostat installation. This could

damage the thermosta t and void the warranty.

• Do not select COOL mode of operation if the outside temperature is below 50˚ F

(10˚ C). This could possibly damage the controlled cooling system and may cause

personal injury.

• This thermostat should only be used as described in this manual. Any other use

is not recommended and will void the warranty.

FEATURES

SPECIFICATIONS

INSTALLATION

Replacing Existing Thermostat

Installing Your New Thermostat

TESTING YOUR NEW THERMOSTAT

PROGRAMMING

Default Thermostat Settings

Setting Current Time of Day and Day of Week

Setting Temperature Differential and Residual

Cooling Fan Feature

Setting First Stage Differential

Setting Second Stage Differential

Setting Residual Cooling Fan Feature

Setting Your Energy Saving Programs

Tips Before Starting

Using Quick Program Groups

or Individual Day Programming

Entering Your Program

ADDITIONAL OPERATION FEATURES

Review Set Temperature

Temporary Program Override

Permanent Hold (Vacation) Mode

Efficient Recovery Mode (ERM

™

)

Compressor Protection

High Temperature Safety Switch

Changing Fahrenheit (˚F) to Celsius (˚C)

Low Battery Detection and Replacement

Replacing the Back-up Batteries

Resetting Thermostat

Multi-Colored LED Indicators

TROUBLESHOOTING

WIRING DIAGRAMS

5.1

3.1

3.2

5.2

5.3

5.4

6.1

6.2

6.3

6.4

6.5

6.6

6.7

6.8

6.9

6.10

5.3.1

5.3.2

5.3.3

5.4.1

5.4.2

5.4.3

6.8.1

Summary of content (11 pages)

PAGE 1
Quick Reference/Installation Guide CONTENTS 1 FEATURES 2 SPECIFICATIONS 3 INSTALLATION MODEL 5200 Premier Series 7-Day Programmable 2-Heat / 2-Cool & Heat Pump Digital Thermostat OWNERS MANUAL Compatible with low voltage multi-stage heat pump systems with up to two stages of heating and two stages of cooling. Not for use on single-stage heating or cooling systems.
PAGE 2
1 FEATURES • Contemporary styling with large display • 7 Day Programming Flexibility • AC Powered with Battery Back-up (2 AA Alkaline batteries included) • Relay Outputs for Maximum Compatibility • Easy Access Front Battery Door • Pre-programmed for quick installation • Meets Title 24 and Energy Star (Energy Saving Guidelines) • Vacation "HOLD" Mode • Compressor Short Cycle Protection • Adjustable 1st & 2nd Stage Temperature Differentials • Residual Cooling Fan Delay • Efficient Recovery Mode (ERM™) • Low
PAGE 3
INSTALLATION 3.2 cont. Installing Your New Thermostat cont. 7. Mark placement of mounting holes as appropriate and drill using a 3/16" drill bit. 8. Gently tap supplied plastic anchors into the holes in the wall. 9. Place the thermostat rear body (mounting plate) against the wall in the desired location making sure the mounting holes are aligned as appropriate and the thermostat wires are properly inserting through opening in middle of rear body. 10.
PAGE 4
5 PROGRAMMING cont. 5.2 Setting Current Time of Day and Day of Week cont. 2. Press the or buttons to set the current hour. 3. Press DAY/TIME button again, the minute portion of the time will flash. 4. Press the or buttons to set the current minute. 5. Press DAY/TIME button again, the day of the week indicator will flash. 6. Press the or 5 5.3 PROGRAMMING cont. Setting Temperature Differential and Residual Cooling Fan Feature cont.. 5.3.2 Setting Second Stage Differential cont.. 3.
PAGE 5
PROGRAMMING cont.. 5 PROGRAMMING cont.. 5.4 Setting Your Energy Saving Programs 5.4 Setting Your Energy Saving Programs cont.yt 5.4.1 Tips Before Starting 5.4.2 Using Quick Program Groups or Individual Day Programming cont.. • It is important for you to set the current time of day (note AM/PM indicator in display), and the current day of week correctly to avoid problems with program execution. This must be done prior to entering any program settings.
PAGE 6
5 PROGRAMMING 6 cont.. ADDITIONAL OPERATION FEATURES cont.. 5.4 Setting Your Energy Saving Programs cont. 6.2 Temporary Program Override 5.4.3 Entering Your Program cont.. 1. Press and hold or buttons for 3 seconds. The entire display will flash once and the SET TEMP indicator will be flashing. Release the or buttons and press the or buttons again as desired to adjust the set temperature. 3.
PAGE 7
6 ADDITIONAL OPERATION FEATURES cont.. 6.5 Compressor Protection cont. NOTE: The installer can reset the thermostat and bypass the compressor protection features by pressing the RESET button. This will erase all entered programs, current time of day, day of week and other user settings and should only be used during installation for testing purposes or to reset a thermostat to regain normal operation. This will return all Thermostat settings to their default values.
PAGE 8
7 TROUBLESHOOTING 7 TROUBLESHOOTING cont. SYMPTOM POTENTIAL SOLUTION SYMPTOM Thermostat does not turn on heating or cooling system. Check to see if OFF is shown in display. This indicates that the system is turned off at the thermostat. Move the system selector switch to the HEAT or COOL position. After the compressor short cycle protection 5-minute period expires the system should start within a minutes time.
PAGE 9
SYMPTOM LO is shown in the thermostat display where the room temperature is normally displayed. POTENTIAL SOLUTION The temperature sensed by the thermostat is lower than the 40˚ F (5˚ C) lower limit of the thermostats display range. The display will return to normal after the sensed temperature rises within the 40˚ to 99˚ F (5˚ to 37˚ C) display range. If the temperature in the controlled space seems to be normal, wait for the thermostat to acclimate to the correct room temperature.
PAGE 10
8 WIRING DIAGRAMS cont. Typical Lennox Heat Pumps (also see other Lennox diagrams) THERMOSTAT TERMINAL BLOCK Y1 Y2 W2 E G O B L C WIRING DIAGRAMS cont.
PAGE 11
8 WIRING DIAGRAMS cont. Typical York E1 Series Heat Pumps THERMOSTAT TERMINAL BLOCK R R HEAT PUMP PCB Y Y1 Y2 W2 E G O B L C User Supplied Jumper W Braeburn Systems LLC warrants each new Braeburn thermostat against any defects that are due to faulty material or workmanship for a period of two years after the original date of purchase by a professional service technician.