User Manual
Table Of Contents
- Network USER’S GUIDE
- Table of contents
- 1 Introduction
- 2 Configuring your network printer
- Overview
- IP addresses, subnet masks and gateways
- Setting the IP address and subnet mask
- Changing the print server settings
- 3 Control Panel Setup
- LAN Main Setup Menu
- TCP/IP
- Ethernet
- Setup Internet (MFC-8860DN only)
- Setup Mail RX (MFC-8860DN only)
- Setup Mail TX (MFC-8860DN only)
- Setup Relay (MFC-8860DN only)
- Scan to E-mail (E-mail server) (MFC-8860DN only)
- Scan to FTP
- Fax to Server (MFC-8860DN only)
- Time Zone (MFC-8860DN only)
- Restoring the network settings to factory default
- Printing the Network Configuration List
- LAN Main Setup Menu
- 4 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 5 Internet printing for Windows®
- Overview
- Quick Tips
- Brother Internet Print General Information
- Brother Internet Print: Configuring the Brother Print Server
- Brother Internet Print: Using the BRAdmin Professional utility to Configure the Print Server
- Brother Internet Print: Using a Web Browser to Configure the Print Server
- Brother Internet Print: Installing the BIP software on Windows® 98/Me/2000/XP and Windows NT® 4.0
- Adding a Second Brother Internet Port
- Windows® 2000/XP and Windows Vista® IPP printing
- Specifying a different URL
- Other sources of information
- Overview
- 6 Network printing from a Macintosh®
- 7 Web Based Management
- 8 LDAP Operation (MFC-8860DN only)
- 9 Internet Fax (MFC-8860DN only)
- Overview
- Getting Connected
- Control Panel Key Functions
- Sending an Internet Fax
- Manually Entering Text
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to your computer
- Forwarding Received E-mail and Fax Messages
- Using E-mail notification with user authentication
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Overview
- 10 Brother Internet Fax Printing Software (MFC-8860DN only)
- 11 Troubleshooting
- Appendix A
- Using services
- Other ways to set the IP address (for advanced users and Administrators)
- Using DHCP to configure the IP address
- Using BOOTP to configure the IP address
- Using RARP to configure the IP address
- Using APIPA to configure the IP address
- Using ARP to configure the IP address
- Using the TELNET console to configure the IP address
- Using the Brother Web BRAdmin server software for IIS* to configure the IP address
- Installation when using a Network Print Queue or Share (printer driver only)
- Multi-function Print Server specifications
- Function Table and Default Factory Settings
- Entering Text
- Index
3
13
3
Control Panel Setup
LAN Main Setup Menu
The control panel LAN menu section can be used to configure network settings.
Press Menu, then press number 6 for MFC-8460N, MFC-8660DN, MFC-8670DN and MFC-8860DN, 4 for
DCP-8065DN and then proceed to the menu selection you wish to configure.
Please note that the machine is supplied with Remote Setup applications for Windows
®
and Macintosh
®
, the
BRAdmin Professional utility for Windows
®
98/98SE/Me, Windows NT
®
4.0 and Windows
®
2000/XP,
BRAdmin Light utility for Windows Vista
®
and Mac OS
®
X 10.2.4 or greater and HTTP protocol (web based
management) for Windows
®
and Macintosh
®
, which also can be used to configure many aspects of the
network. See
Changing the print server settings
on page 10 for Windows
®
and
Changing the print server
settings
on page 51 for Macintosh
®
.
TCP/IP
This menu has ten sections: Boot Method, IP Address, Subnet Mask, Gateway, Node Name, WINS
Config, WINS Server, DNS Server, APIPA and IPv6.
BOOT Method
1
(For MFC-8460N, MFC-8660DN, MFC-8670DN and MFC-8860DN) Press Menu, 6, 1, 1.
(For DCP-8065DN) Press Menu, 4, 1, 1.
2
Press ▲ or ▼ to select Auto, Static, RARP, BOOTP or DHCP.
3
Press OK.
4
Press Stop/Exit.
Auto mode
In this mode, the machine will scan the network for a DHCP server, if it can find one, and if the DHCP server
is configured to allocate an IP address to the machine, then the IP address supplied by the DHCP server will
be used. If no DHCP server is available, the machine will scan for a BOOTP server. If a BOOTP server is
available, and it is configured correctly, the machine will take its IP address from the BOOTP server. If a
BOOTP server is not available, the machine will scan for a RARP server. If a RARP server also does not
answer, the machine will use an APIPA address, see
Using APIPA to configure the IP address
on page 90.
This whole process can take 2 to 3 minutes so we recommend printing a Network Configuration List to confirm
the network settings are set correctly.
Static mode
In this mode the machine’s IP address must be manually assigned. Once entered the IP address is locked to
the assigned address.