BRAN INSTALLATION AND USE & CARE INSTRUCTIONS N SAFETY Please visit our websites www.broan.com, or www.broan.ca to register this product and to view installation tips and videos, Installer: Leave this manual with the homeowner. READ AND SAVE THESE INSTRUCTIONS A To reduce the risk of fire, electric 75 shock, or injury to persons, observe the following: * Use this unit only in the manner intended by the manufacturer.
ALL INSTALLATIONS Start here. < COOKING AREA \, Do installation above or / N, inside this area 480 7 N < |/ / NOT FOR USE IN A COOKING AREA. Cooking Equipment Flora & "% IMPORTANT The ducting trim this fan o the outside of the building has a strong affect on the air flow, rouse and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended.
6. Connect 4-in. round duct. INSTALLATION AND USE & CARE INSTRUCTIONS INSTALLATION o= NEW CONSTRUCTION For Retrofit Installation Skip to Page 5. 4. Attach damper/duct connector : to fan housing. Ble O Push connector through opening from inside of housing. Engage tabs and secure with resew from parts bag. 7. Connect wiring. Bend tab to expose desired access hole. Connect power cable to housing with appropriate UL approved connector. Connect black to black, white fo white and green fo green or bare wire.
8. Install blower. Re-install blower. Secure blower with 2 screws from parts bag and plug blower into black receptacle. 9. Finish ceiling, then install grille. Plug light into receptacle in housing, Attach grille pan to housing with (2) grille mounting screws. install (2) 60W {Max.) candelabra bulbs (not included). Attach shade using hardware as shown. Do not over tighten finial nut.
BRAN INSTALLATION AND USE & CARE INSTRUCTIONS INSTALLATION (=2 6. Connect wiring. Bend tab to expose desired access hole, Connect power cable to housing with appropriate UL approved connector. Connect black to black, white to white and green to green or bare wire. Re-install wiring panel and secure with screw from parts bag. 7. Mount fan to ceiling structure. Mount housing to ceiling structure with standard drywall or wood screws in cations show, *Center hole optional. 8. Connect 4-in. round duct.
MODELS AR70PS, ARBOR SERVICE PARTS Key No. | Part No. | Description 1 7019614 | Housing 2 870195861 | Duct Connector 4-in. 3 97019516 | Wire Panel Assembly 4 97019918 | Blower Assembly B 90528761 | Grille Bracket Assembly € 90528801 | Glass Shade 99528803 | Shade Mounting Hardware (AR70PS) 98528804 | Shade Mounting Hardware (ARBOR) s 98528806 | Grille Pan Assembly (BARHOPS) 99528807 | Grille Pan Assembly (ART ORB) DOBBED | Light Fixture Assembly (AR7CPS) A (includes Key Nos.
BRAN INSTALLATION AND USE & CARE INSTRUCTIONS ©0O WARRANTY Limited Warranty Warranty Period and Exclusions: Brian-NuTone LLC (the, Company,) warrants to the original consumer purchaser of its product { you,) that the product {the, Product,) wil be free from material defects in the Product or its workmanship for a period of three (3) years from the date of original purchase.
CONSTRUCTION NEUVE BREN 6. Connectez un conduit rond po). Pour une rénovation passez & la page 12, 4, Fixez le clapet/raccord de conduit au boîtier de ventilateur. Poussez le raccord au travers de Ouverture par 'intérieur du bottier. Engagez les ergots &t fixez Ie tout avec les vis se trouvant dans le s: our exposer e ou d’aces voulu, sédimentation au voilier 2 i connectable approprié homologué UL.
BRAN DIRECTIVES D'INSTALLATION, D'UTILISATION ET D’ENTRETIEN INSTALLATION 8. Installez le ventilateur. Reposez le ventilateur, Fixez-le avec 2 vis Gu sachet de piques et branchez-le dans lz prise noire. 9. Finissez le plafond, puis installez la grille. Branchez la lumière dans la prise de courant du bottier. Fixez la plaque de grille au boîtier avec les deux (2) vis de montage de 1z griffe, Inslaliez deux (2) ampoules canes (max.) (nen comprises).
BECAN INSTRUCCIONES DE INSTALACIÓN, USO Y CUIDADO INSTALACIÓN m—t CONSTRUCCIÓN NUEVA Para instalaciones de conversión: pase a Ia pagina 19. 4. Acople el conector del regulador de tiro/conducto a la cubierta del ventilador. Empuje & conector a través de la abertura desde el interior de {a cubierta, Encaprichen fas lengüetas v fijezas con los dornillos de la bolsa de piezas. 5. Monte la cubierta en la estructura del cielo raso.
8. Instale el soplador. BREN Vuelva a instalar el soplador, Afielo con 2 fornicios de la bolsa de piezas y conecte &l soplador en ef receptáculo negro. C INVERSIONISTA 4. Quite el ventilador viejo. De ser necesario, agrande 1 abertura dei cielo ras 3 9% pulga. {24.7 e (pelaire & la vigueta) por 10 % pulga [26.7 cm] (perpendicular a la vigueta). Daca ef cateado y s conductos existentes en su ligar. 9. Termine el cielo raso y a continuación instale la rejilla. Enchufa la luz en gt receptáculo de 2 cubierta.
7. Monte el ventilador en la estructura del cielo raso. 6. Conecte el cableado. Monte la cubierta en la estructura det siclo ras con tormos ran. Doble fa alienista para exponer el orificio de accesos deseado. estándar groa madera 0 yeso en s lugares que s¢ mus sira Conecte el cable eléctrico & la cubierta con una conexión "B orificio central es oracional, apropiada aprobara por UL.